User Manual Pepwave Surf Indoor Series: Surf mini Surf On-The-Go Surf 400 Pepwave Surf DX Series: 400-DX Document Rev. 9.0.33 May 11 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Copyright © 2011 Pepwave Ltd. All Rights Reserved. Pepwave and the Pepwave logo are trademarks of Pepwave Ltd. Other brands or products mentioned may be trademarks or registered trademarks of their respective owners.
User Manual Pepwave PolePoint Series Table of Contents 1 COPYRIGHT ............................................................................................................. 3 2 DISCLAIMER............................................................................................................. 3 3 PRODUCT DESCRIPTION ........................................................................................ 4 3.1 PRODUCT FEATURES .........................................................................
User Manual Pepwave PolePoint Series 1 Copyright Copyright © 2011 by Pepwave Ltd. The content of this documentation may not be reproduced in any part or as a whole without the prior written permission of Pepwave Ltd. 2 Disclaimer Pepwave does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent right nor the patent rights of others.
User Manual Pepwave PolePoint Series 3 Product Description 3.1 Product Features Signal strength LED for showing the current signal strength Always-on, integrated Wi-Fi access point WPA/WPA2-Personal and WPA/WPA2-Enterprise security support Wi-Fi Multimedia (WMM) support Built-in DHCP server and NAT routing to manage client devices Customizable, built-in web portal for simple web-based configuration Surf mini / Surf On-The-Go http://www.pepwave.
User Manual Pepwave PolePoint Series 3.2 Hardware Setup 3.2.1 Surf mini / Surf On-The-Go Series 1. Attach the provided antenna to the right most antenna connector 2. Connect the LAN port to the computer’s Ethernet port with an Ethernet cable. 3. Connect the end of the included power adapter to the power socket on Pepwave Surf mini. 4. Power on the power adaptor. 3.2.2 Surf 400 Series 1. Attach the provided antenna to the left most antenna connector 2.
User Manual Pepwave PolePoint Series 3.3 LED Description 3.3.
User Manual Pepwave PolePoint Series 3.3.
User Manual Pepwave PolePoint Series 3.3.3 Surf DX Series LED PWR LAN Wi-Fi http://www.pepwave.com Color Status Description Green On Power is on Off Power is off On Ethernet is connected Off Ethernet is not connected On Associated with an access point. The number of LED lights from “MIN” to “MAX” indicates the received signal strength level.
User Manual Pepwave PolePoint Series 4 Using the Pepwave Devices 4.1 Pre-configuring PC Setup You should set up your computer’s LAN interface to obtain an IP address automatically. In order to do so, select the Start menu > Control Panel > Network Connections. Right click on the Local Area Connection icon, choose Properties, and double-click on the item Internet Protocol (TCP/IP) from the list. On the screen, just set it as follows: Click the OK button to confirm the change. http://www.pepwave.
User Manual Pepwave PolePoint Series 4.2 First Time Setup On your PC, start a web browser, e.g. Internet Explorer, Mozilla Firefox, etc. Visit an Internet web site. If you are not associated to an access point, you should be redirected to a logon page. Or you can go to the following URL: http://192.168.20.1/ The page will look like this. Illustration 1: Welcome Page http://www.pepwave.
User Manual Pepwave PolePoint Series Click the Advanced Config button to enter the parameters of the access point to associate to. You should see this screen: http://www.pepwave.
User Manual Pepwave PolePoint Series Illustration 2: Pepwave Surf Setup Page In the field SSID under Wireless Settings, input the access point’s SSID (sometimes it is called the “network name”). According to the setting of the Access Point you are associating to, you may choose a different Authentication setting. If Static WEP key or WPA/WPA2-Personal is selected for Authentication, input the Encryption Key field as well. (There are also options of 802.
User Manual Pepwave PolePoint Series Illustration 3: Establishing Connection to the Internet At this point, you are associated with the access point. You may now close the web browser and open a new one to start web browsing. http://www.pepwave.
User Manual Pepwave PolePoint Series 5 CPE Settings Details 5.1 IP Settings Illustration 4: IP Settings Illustration 5: DHCP Reservations IP Settings LAN Interface To configure the LAN interface’s IP address and subnet mask. DHCP Server To configure and enable the built-in DHCP server or not. If enabled, the IP address range can be configured. Configure DHCP Reservation if there is a need to assign a specific IP address to a specific MAC address using DHCP. http://www.pepwave.
User Manual Pepwave PolePoint Series 5.2 Radio Settings Illustration 6: Radio Settings Radio Settings Radio Mode Channel Width Country Channel Scanning Mode Bit Rate It allows the user to choose between radio modulations support: 802.11na, 802.11ng, 802.11b/g, 802.11b only, etc. The available settings depend on the Wi-Fi module installed on the device. This option will only be available if you have selected 802.11na or 802.11ng in the previous field.
User Manual Pepwave PolePoint Series 5.3 Wireless Settings Illustration 7: Wireless Settings Wireless Settings WAN Mode SSID Connect to Any Open Mode AP Passive Scan Authentication This option specifies your Internet connection source. Select Wireless if you are using the device as a Wi-Fi receiver. Select Wired if you are using the device as a standard Access Point. To configure the Network Name of the wireless network to associate with.
User Manual Pepwave PolePoint Series Allow Repeater AP Connection Preferred AP Select Enable to allow the connection from a repeater AP. The MAC address of a preferred access point can be entered here. When the preferred access point is found and its signal strength is higher than the Min Signal Strength, it will connect to this preferred access point, no matter the other access points are found even they have higher signal strength or the same SSID. http://www.pepwave.
User Manual Pepwave PolePoint Series 5.4 Roaming Settings: Illustration 8: Roaming Settings Roaming Settings Roaming Settings To configure and enable roaming among APs with the same SSID and authentication method. Background Scanning Interval The time interval between background scans. Roaming Threshold (Signal Level Gain) http://www.pepwave.
User Manual Pepwave PolePoint Series 5.5 Wireless IP Settings Illustration 9: Wireless IP Settings Wireless IP Settings The IP address can be obtained automatically or configured manually. If you choose to manually configure the IP address for your unit, enter the fields IP Address, Subnet Mask, Default Gateway, Preferred DNS Server and Alternate DNS Server. IP Settings Select Obtain an IP Address using DHCP and the device will obtain an IP from the DHCP server automatically.
User Manual Pepwave PolePoint Series 5.6 Restore and Reboot Illustration 10: Restore and Reboot Restore and Reboot WAI Redirection If the device is not connected to an access point, and the user is accessing an Internet web site, the settings control whether to redirect the web access to the web admin interface page or not. If this is disabled and the device is not connected, the browser will show a web access error message.
User Manual Pepwave PolePoint Series 5.7 Integrated Wi-Fi Access Point Configuration Integrated Wi-Fi Access Point is configured via the CPE Setup tab. The following sections will provide information as a guide through the configuration. The available Access Point (AP) settings for the Integrated Wi-Fi Access Point functionality are as follows: Disable Integrated Wi-Fi Access Point functionality is disabled.
User Manual Pepwave PolePoint Series 5.7.2 Access Point Disabled Access Point feature will be disabled when Disable is selected. Illustration 11: Access Point Disabled 5.7.3 Access Point configure Manually Illustration 12: Access Point Configure Manually Configure Manually AP SSID In Manual Configuration mode, the SSID is manually entered. It can be one of three configurable values: Authentication http://www.pepwave.com • Open No Encryption Key is necessary.
User Manual Pepwave PolePoint Series 5.7.4 Access Point Configure Automatically Illustration 13: Access Point Configure Automatically With the Access Point Configuration set to Configure Automatically, the SSID, Authentication, and Encryption Key values of the Integrated Wi-Fi Access Point will be configured to be the same as in the Wireless IP Settings section. Important Note In the Wireless Settings section, if Authentication is set to either 802.
User Manual Pepwave PolePoint Series 6 Port Forwarding Port Forwarding Settings Service Port Range Protocol IP Address Del Enter a port or a range of ports that would like to forward. The Protocol for the above port(s) forwarding. You should select at least one protocol between TCP and UDP. The IP address that you would like the traffics forwarded to. By clicking the button, you can delete the corresponding rows of port forwarding rules. Illustration 14: Port Forwarding http://www.pepwave.
User Manual Pepwave PolePoint Series Below the port forwarding table is an option called DMZ Host. If you Enable this function, your Pepwave Surf will become a DMZ device. You can enter an IP address, which will be the IP address of the device that expose to the Internet. The purpose of a DMZ is to make all external users can has access to any ports of the device, so that user do not need to set up port forwarding and internet traffics can directly reach internal devices.
User Manual Pepwave PolePoint Series 7 QoS QoS Settings Target To choose whether it is an incoming (Source) or outgoing (Destination) traffic that should be controlled by the service. Service Port Range Enter a port or a range of ports that would like to be controlled by the service. Protocol IP Address The Protocol for the above port(s). You should select at least one protocol between TCP and UDP. The IP address that you would like the traffics to be controlled by the service.
User Manual Pepwave PolePoint Series 8 Firmware Upgrade The Pepwave devices are able to check whether a newer firmware (the software running on the unit) is available. However, it is recommended that you do not update the firmware unless specifically instructed by your ISP to do so. When a firmware upgrade is needed, your ISP will either give you instructions or they will upgrade the firmware remotely.
User Manual Pepwave PolePoint Series 9 Debug and System information Illustration 17: Debug tab showing the system information http://www.pepwave.
User Manual Pepwave PolePoint Series Tip Debug dump and configuration file can be downloaded through clicking the links illustrated above. If you encounter issues and would like to contact Pepwave Support Team (email: support@pepwave.com), please download the above files and attach it along with a description of your encountered issue. http://www.pepwave.
User Manual Pepwave PolePoint Series 10 Restore to Default Settings 10.1 Surf Indoor Series There are two ways to restore the Pepwave Surf Indoor unit to default settings. If you are able to access the web admin interface, go to the CPE Setup page, and click the Restore and Reboot button. Otherwise, you can also power up the unit and wait for about 1 min. Then press the Reset Button at the rear side of the unit using a pin and then hold it for 5 seconds.
User Manual Pepwave PolePoint Series Appendix Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
www.pepwave.com Contact Us: Sales http://www.pepwave.com/contact/sales/ Support http://www.pepwave.com/contact/ Business Development and Partnerships http://www.pepwave.
