Piri 2096 Manual 1 (12) Piri 2096 Manual Nordic Light AB Postal Address: Servicegatan 13, SE-931 76 Skellefteå, Sweden Tel Int: +46 910 733790 Fax Int: +46 910 16445
Piri 2096 Manual 2 (12) CONTENTS 1.0 General Information ......................................................................................................................................................................3 1.1 Reference .....................................................................................................................................................................................3 2.0 Description of module ...............................................................
Piri 2096 Manual 3 (12) 1.0 General Information This document is intended as a manual to describe how to integrate the Piri 2096 radio module in end products. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation 1.
Piri 2096 Manual 4 (12) 2.0 Description of module The module utilize Lora modulation that uses Chirp Spread Spectrum modulation (CSS) for RF communication at 2.4 GHz and ARM Cortex M MPU as the controller for the RF circuit. CON1 CON11 CON2 . . . .
Piri 2096 Manual 5 (12) 2.1 Communication Frequency and Settings The communication frequency spans over the 2402->2480 MHz band. All Piri systems are geo positioned before RF communication can start as it automatically selects the regional settings required for compliance with RF communication in different regions. 2.2 Transmission The module utilize LBT/FHM time slot based protocol to handle the transmission between devices. 2.
Piri 2096 Manual 6 (12) 3.0 Specification 3.1 Electrical Voltage input range of 4.5->12VDC. Current consumption: <30 mA Communication signals: 3.3V CON11 3.2 Electrical connections Connection CON1 CON2 CON3 CON4 CON5 CON6 CON7 CON8 CON9 CON10 CON11 Function VCC GPIO GPIO GPIO GPIO GPIO GPIO GPIO GPIO GPIO GND USB micro (optional ) CON1 J1 Flex strip connector (optional ) CON2 CON3 CON4 CON5 CON6 CON7 CON8 CON9 CON10 Indicator LED:s 3.
Piri 2096 Manual 7 (12) 3.4 Mechanical and installation As the module is intended for different solutions the mechanical structure is done so it can be both mounted as a SMT mountable component, as a remote positioned part within the system with flex strip or by USB micro connection. Size (Width x Length x Height): 30 x 40 x 5.
Piri 2096 Manual 8 (12) Example of SMT soldering profile is shown below Do not exceed peak temperature and slope time between preheat and peak solder zone. 3.5 Label The module is fitted with an identifying label on the RF shield box as shown on picture below.
Piri 2096 Manual 9 (12) 3.6 Pictures Picture of radio module. 4.0 Module features 4.1 Connectors The module has a number of communication I/O:s that can be used in order to communicate with the controller through the flex strip connector J1 [1] or the castellated connection points on the PCB [2]. A connector pad J4 [1] is on the PCB for evaluation of environmental introduced RF properties. The USB connector and J1 is an option.
Piri 2096 Manual 10 (12) 5.0 Compliance Information 5.1 Federal Communication Commission (FCC) Statement Compliance statement This device complies with part 15 of the FCC Rules. Operations is subjected to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Piri 2096 Manual 11 (12) 5.2 Innovation, Scientific and Economic Development Canada (ISED) Statement Radiation Exposure Statement for Canada This device complies with the Industry Canada’s licence-exempt RSSs. Operation is subjected to the following two conditions: (1) This device must not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Piri 2096 Manual 12 (12) 5.2 End Product Labeling PIRI 2096 has been labeled with its own FCC ID and IC Certification number. The end product manufacturer must ensure that FCC and ISED labeling requirements are met. If the FCC ID and IC Certification number of PIRI 2096 are not visible when the module is installed in another device, then the device must have a clearly visible label containing the following information. PIRI 2096 a été étiqueté avec son propre ID FCC et son numéro de certification IC.
