955Series WELLCORE○iBeaconW9 R Product Specification V1.08-2018 V1.
.4 Login password and revise ................................................................................................................ 6 2.5 UUID revise ............ ......................................................................................................................... 7 2.6 Majorrevise...................................................................................................................................... 8 2.7 Minorrevise...............................................
candeterminewhenthis broadcastinformationiBeaconlocation, but also by APPmobile clienttells the serverhasaccess to theiBeaconbroadcast area. iBeaconsend tophone only broadcast informationwithoutany other information,but according tobroadcastinformationsent byiBeacon , the phone can downloadrequired information in relevant server. 1.
2.3 Light bluemenu Introduction Open the software Light blue, this time will automatically search out iBeacon device can also be connected to the sliding screen refresh Equipment, open software displays the following figure, this time in the menu Peripherals Nearby displayed at WGX ibeacon It means that the search has been successful to the device, the device name is WELLCORE factory default settings, the user can modify Refer to Section 2.9 to modify the method. Figure 1 Wellcore Technology Co.
Wellcore Technology Co., Ltd © WELLCORE 2011. All rights reserved http://www.wellcore-tech.com http://www.wellcore WELLCORE○ R iBeaconW91 Series 2.4 The login password and how to modify. Attention: For the iBeacon we provide, the login password is needed if want to check or modify Device Parameters. The original code is:140611,Please see Figure3 Figure3-5 5 for the right way of Entering the password.Before Before entering the right password, it all shows 00(Figure (Figure 3 ) on the Icon:READ Icon again.
AA140611,Prefix AA means enter password,Click done when finished.now you canCheckModify other parameters, It means the password is wrong if you can not see theparameters,Then need to enter the right password. Modify password(Figure 5 ): Only can modify the password when the right passwordhas been put in. For example if you need to modify password to be : 123456,then youNeedEnter AC123456, Prefix AC means modify password,the password can be6-20 letters.ClickDone when finished.
not be searched out on Locate ibeacon after finished modify UUID, As Locate ibeacon can only shows the Registered device,so you need to add a modified UUID device on the Options of iBeacon Transmitter. . Figure 6 Figure 7 Wellcore Technology Co., Ltd © WELLCORE 2011. All rights reserved Figure 8 http://www.wellcore-tech.com WELLCORE○ R iBeaconW91 Series 2.
Figure 9 Figure 10 Wellcore Technology Co., Ltd © WELLCORE 2011. All rights reserved Figure 11 http://www.wellcore-tech.com WELLCORE○ R iBeaconW91 Series 2.7 Minor revise Minor is 2digits(4characters)HEX value, default value is (Figure 12):0000,For example, modify Minor to be: 8811,Then write Corresponding values in the “Write new value”( Figure 13),Click Done when finished.Meanwhile, the new set Minor shows on the Read again(Figure14).
Figure 12 Figure 13 Wellcore Technology Co., Ltd © WELLCORE 2011. All rights reserved Figure 14 http://www.wellcore-tech.com WELLCORE○ R iBeaconW91 Series 2.8 Measured Power revise Measured Power is a 1digit(2 characters)HEX value, default value is(Figure15):C5,Forexample, modify Measured Power to be: C6,Then write Corresponding values in the Write new value(Figure 16), Click Done when finished.Meanwhile, the new set Measured Power shows on the Read again(Figure17).
Figure 15 Figure 16 Wellcore Technology Co., Ltd © WELLCORE 2011. All rights reserved Figure 17 http://www.wellcore-tech.com WELLCORE○ R iBeaconW91 Series 2.9 Device name revise Device Name is 1-15 characters (ASCII Code), the default device name is “WGX ibeacon”(Figure 18)Example:Modify the Device name is:“wellcore01”: Writing the corresponding values in the place of "Write new value"(Figure 19). After finished Click“Done”to exit.
in ASCII.So before modifying,click the top right corner of the“Hex”(Figure 18),And change to the entry mode of“UTF-8”(Figure 19). Please pay attention:You should re-search the device again then it can display the New Modified Device Name. Figure 18 Figure 19 Wellcore Technology Co., Ltd © WELLCORE 2011. All rights reserved Figure 20 http://www.wellcore-tech.com WELLCORE○ R iBeaconW91 Series 2.
+4db.Example:Modify the Transmit Power is 01: Writing the corresponding value in the place of "Write new value"(Figure 22). After finished Click“Done”toexit.At this time it can display the new Transmit Measured Power in the place of "Read again" (Figure 23). Please pay attention:You should modify transmit power according to the actual needs,"09 --- +4db" corresponds to the maximum power, the signal transmission distance can up to 100 meters, but the battery life will be relatively short.
this time it can display the new Broadcast Frequency in the place of "Read again" (Figure 26). Please pay attention:You should modify the Broadcast Frequency according to the actual needs,the Broadcast Frequency is small and power consumption is also small.The battery life will be relatively increased. Figure 24 Figure 25 Wellcore Technology Co., Ltd © WELLCORE 2011. All rights reserved Figure 26 http://www.wellcore-tech.com WELLCORE○ R iBeaconW91 Series 2.
Figure 27 Wellcore Technology Co., Ltd © WELLCORE 2011. All rights reserved http://www.wellcore-tech.com WELLCORE○ R iBeaconW91 Series 2.13 BT vendor ID revise "BT vendor ID " is a 2 byte (4 characters) HEX value, the default value is 004C (Figure28),This ID by the Bluetooth Association of distribution companies, such as NORDICCorp is :0059, the Apple Corp is :004C ,Example:Modify the BT vendor ID is 0059,Writting the "0059" in the place of "Write new value"(Figure 29).
Figure 28 Figure 29 Figure 30 2.14 Deploy mode revise "Deploy mode " is a 1 byte (2 characters) HEX value, the default value is (00), Deploy mode:value 70(careful operation, set up after the parameters can not be modified forever),Normal mode:value 00 0 (can be modified parameters) ,Example:Modify Example:Modify the value is 70,Writting the "70 70" in the place of "Write new value"(Figure 31). ). After finished Click “Done”to exit. Figure 30 Figure 31 Wellcore Technology Co., Ltd © WELLCORE 2011.
3.2 The Use-method of Locate iBeacon 1.Open the software “Locate ibeacon” (Figure 28).Click“LocateiBeacons”you can enter the next two levels of menu (Figure29,30)At this time you can see all the informations of the device.Such asUUID,Major ,Minor, ISSI,RangeInformation,etc. Figure 28 Figure 29 Wellcore Technology Co., Ltd © WELLCORE 2011. All rights reserved Figure 30 http://www.wellcore-tech.
Figure 31 Figure 32 Wellcore Technology Co., Ltd © WELLCORE 2011. All rights reserved WELLCORE○ R iBeaconW9Series 4Product certification: CE,FCC ,ROHS 4.1 FCC ID: Figure 33 http://www.wellcore-tech.
Wellcore Technology Co., Ltd © WELLCORE 2011. All rights reserved WELLCORE○ R iBeaconW91 Series 5Electrical Parameters: 5.1 Hardwareversion: Nordic NRF51822. 5.2 Operating Voltage: 1.8-3.8V 5.3Bluetooth: BLE V4.0 5.4OperatingFrequency:2.4GHz ISM band 5.5Modulation:GFSK(Gaussian Frequency Shift Keying) http://www.wellcore-tech.
6Use Environment: 6.1 Operating temperature: 6.2 Storage Temperature: 6.3 Environment Humidity: -25~+65℃ -40~+75℃ 5%~85% 7 Product Specifications 7.1 Model: W956D 1Product photos 2 Mechanical Dimensions: L*W*H: 100*68*50mm 3Weight: 230g 4 Batterytype: ER34615(19000mAH) (broadcast frequency of 1 second, the power of 0dB working more than 10 years). 5 Product Description: with waterproof function, waterproof grade IP67. Wellcore Technology Co., Ltd © WELLCORE 2011. All rights reserved http://www.
FCC Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.