Manual
I
I TWO MODES COUNTER
Counter Mode button (TIME/COUNT)
Press the button, and 2 modes change alternately.
Tape counter _ Time counter
• Tape counter
Different counters are provided for DECK 1and 1|. The number on
the counters increase/decrease as a tape runs. It is useful if you
make a note of the location and length of a selection while re-
cording or playing back. You can then easily locate a desired se*
lection or where to resume recording.
• Time counter
• This indicates the elapsed time for recording or playback, This
automatically starts counting when recording or pleyback starts.
During fast-forwarding/rewinding, the counter automatically
switches to a tape counter.
• The time counter indicates only the time duration of recording or
playback. When recording or playback is changed to fastforward-
ing, rewinding, or music search, the counter switches from the
time counter to the tape counter. When the operation returns to
recording or playback, the counter switches to the time counter.
• Tape counter indication
I-I I-I I--I I-'1
I_1 I_1 LJ I_1
• Time counter indication
I'_ i'_. I-I N
/_1 /-I. I_l LJ
I
FRONT PANEL FACILITIES i
Counter reset button (RESET)
Press this button to reset the tape counter to 0 o _ 0, or to reset the
time counter to un 0:0 0.
Counter indicator during music search
0Q_ID I Nomral tape counter indicator I
!
Counter indicator during music search
PIP0
Plus sign
PI-O
Minus sign
• A plus sign (+) appearsduring music search in the forward direction.
• A minus sign (-) appears during music searchin the reverse direction.
PLAYBACK
SINGLE PLAYBACK (Either DECK [ or DECK 1[)
1 5 5 1
II
!
3 2
The above illustration shows CT-W616DR.
1. Load a prerecorded tape in DECK [ or 1[.
2. Select the Dolby NR mode with the OOLBY NR button.
• Always set the same Dolby NR system that was used for re-
cording.
3. Select the reverse mode with the REV MODE button
(see page 9).
4. Set the stereo amplifier for tape playback.
5. Pressthe playbeck (_ er <) button of either DECKI er rl.
To improve high frequency sound during playback In
tapes with poor recordings (Except for U.S. model of CT-
W606DRI
Pressthe FLEXbutton and playbackthe tape,
To stop playback temporarily (DECK 1[ only)
Press the pause (11)button.
• To resume playback, either press the pause 111)button again, or
press the playback (_ or <1)button,
The last two digits of the counter indicator show the number of
selections to be skipped. If three selections are to be skipped, for
example, it shows "P+03" initially.The number then decreases by
1 each time a selection is skipped ("P+02" -- "P+01 etc.). When
the deck resumes playback, the normal tape counter reappears,
I
BLANK SKIP
This function allows you to skip unrecorded portions of the tape
during playback
Press the REV MODE button to c-*.__.
NOTE:
• When the REV MODE button is set to the c-.D position, the relay
mode will be selected
• When this mode is selected, ff the tape deck encounters an unre-
corded portion of tape more than 15 seconds in length, it will fast
forward the tape until it encounters another recorded portion, and
resume playback from that point.
11
<RRB1176>
En
To stop playback
Press the stop (11)button.
Select the reverse mode with the REV MODE button to c-'.__,
To fast forward or rewind tape
: Press in stop mode to fast forward the tape on the side which
can be seen through the cassette door (the tape on the invis
ible side isrewound),
414 : Press in stop mode to rewind the tape on the side which can
be seen through the cassette door (the tape on the invisible
side isfast forwarded),