PLEASE READ THE INSTRUCTIONS Styles and colors may vary ◎Suitable age for 3‐8 Years ◎Maximum user weight: 30kg ◎Adult assembly required INSTRUCTION MANUAL
Charge for 4-6 hrs before initial use. After initial charge, follow the normal recommended Charging time.
SAFETY Please retain these instructions for future reference. NOTE:For best performance,only use this vehicle on flat and hard surfaces. AGE RANGE:3 to 8 years old WEIGHT CAPACITY:30KG is the maximum weight for 1rider(combined) The following safety hazards may result in serious injury or death: This product contains small parts.Keep children away during assembly.Make sure to remove all packaging material and parts from underneath the vehicle body. Never open the battery.
BATTERY WARNINGS The following safety hazards may result in serious injury or death: Use of a battery or charger other than the supplied rechargeable battery and charger may cause a fire or explosion.Only use the supplied battery and charger. Use of the rechargeable battery and charger for any other product may result in overheating,fire,or explosion.Never use the supplied rechargeable battery and charger with another product. Explosive gases are created during charging.
USER WARNINGS The following safety hazards may result in serious injury or death: Never leave a child unattended. Always sit in the seat when using this vehicle. Keep your hands,hair,and clothes away from moving part. Always wear shoes when operating this vehicle. Maximum of two children are allowed in the vehicle at a time. Children under 3 years of age cannot use the vehicle. Only drive on level ground.
TOOLS REQUIRED SCREWDRIVER NEEDLE NOSE PLIERS (BRING YOUR OWN) (NOT INCLUDED) HARDWARE 1 M4*10mm SCREW 2 10 PCS φ10 WASHER 3 COTTER PIN 7 PCS 4 PCS PARTS A CART WHEELS B SEAT 1 PCS I CHARGERS 1 PCS C 1 PCS 4 PCS E WINDSHIELD F STEERING WHEEL 1 PCS WHEEL COVER D 1 PCS 4 PCS G REAR SUPPORT FRAME 2 PCS MIRROR(L/R) H REMOTE CONTROL 1 PCS
PRODUCT ASSEMBLY (SINGLE DRIVE) Put the gasket, Cart wheels, gasket and cotter pin into the front axle in turn. Insert the cotter pin into the hole of iron piece and bend it to fix itand then attach the wheel cover to the wheel. Place the Cart wheels, Washer, and cotter pin on the rear axle in turn. Insert the cotter pin into the hole of iron piece and bend it to fix itand then attach the wheel cover to the wheel.
PRODUCT ASSEMBLY (DUAL DRIVE) Put the gasket, Cart wheels, gasket and cotter pin into the front axle in turn. Insert the cotter pin into the hole of iron piece and bend it to fix itand then attach the wheel cover to the wheel. Place the Cart wheels, Washer, and cotter pin on the rear axle in turn. Insert the cotter pin into the hole of iron piece and bend it to fix itand then attach the wheel cover to the wheel.
PRODUCT ASSEMBLY G 1 Place the rear bumper reinforcement on the body as shown in the figure; And fixed with M4 *10 screw; Put the vehicle upside down 1.
PRODUCT ASSEMBLY Follow the assembly steps in the order listed below. F Attach the steering wheel. Remove the nut and bolt from the steering wheel. Connect the wires coming from the steering column to the wires on the steering wheel. Insert the steering wheel over the steering and secure with nut and bolt.
PRODUCT ASSEMBLY D B Stuck the mirror into the windshield and fix it with M4*10 screws; Stuck the windshield into the corresponding slot on the body
DASHBARD DIAGRAM 1. 2. 3. 4.
DASHBARD DIAGRAM 5. Power button:Long Press it 3 seconds,Turn the vehicle on and off 6. Wireless Technology : After connected your mobile phone and the wireless device ,the car can play music from your mobile phone 7. FM: Radio, long press it 2-3 seconds, the light of FM button will flash and Automatic search, when the search completes, the FM key stops flashing 8. Music Button:play music 9. Last song:Switch songs/and long press will decrease volume 10.
REMOTE CONTROL DIAGRAM Warning Only used by adults Remote control first. When the remote control is on, foot pedal is not workable Operation Manual: Take out the remote control, Open the battery compartment on the back of the remote control and add two AAA LRO3 alkaline batteries. Pay attention to the polarity of the batteries. When the alignment light and speed indicator light up, it indicates that the battery installed is correct. This product does not provide dry batteries.
2) Brake button: Press it to stop moving; press it again to move. 3) Speed selection key and speed indication: used to select speed of the car. Press the key once to switch the speed once. 3 speeds are cyclically switched, and the switching sequence is: low-medium-high. The speed indicator is arranged from top to bottom on the remote control: high-speed lamp, medium-speed lamp, low-speed lamp; when switching to one speed, the corresponding indicator lamp will light up.
CHARGING INSTRUCTIONS 1.Insert the charger jack into the charging hole of the car. 2.Plug the charger plug into the stable matching AC power supply as shown in the picture. Charge the battery 15 to 18 hours before initial use. On average.you will need to charge the battery between 8 and 12 hours.Do not charge the battery for more than 20 hours.
CARING FOR YOUR RIDE-ON Park the vehicle indoors or cover it with a tarp to protect it from wet weather. Do not leave the vehicle in the sun for long periods of time or fading may occur. Store in shade or cover with tarp. Do not wash the vehicle with a hose. Do not wash the vehicle with soap. Charge battery at least once a month to prolong the life of the battery.
WARNINGS REGARDING BATTERIES The battery on the vehicle is not replaceable. DO not mix old and new batteries. DO not mix alkaline,standard(carbon-zinc),or rechargeable batteries. Non-rechargeable batteries should not be charged. Rechargeable batteries should be charged under adult supervision only. Exhausted batteries should be removed. The supply terminals should not be short-circuited. Do not put batteries next to or in a heat source(fire,electronic heating device,etc.
FCC Statement Caution: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.