SECURE INSTALLATION GUIDE LATCH EDITION
Go to LOCKLY.com/installation to watch a video version of this installation guide. OR Download the BILT app in the Apple or Google Play store for step-by-step interactive 3-D walk-through installation instructions.
Welcome! This guide will walk you through step-by-step how to install and get your LOCKLY® Secure up and running. Installation generally takes less than 30 minutes. If you have any questions please reference our online support at: LOCKLY.com/support or call (669) 500-8835 for help.
Preparation To complete the installation you will need: Phillips Screwdriver Pliers Flathead Screwdriver Tape measure or ruler Screwdriver with drill bits (Optional) Drilling is not required to install the lock, and is optional. However if you are installing your lock on a brand new door, a drill is required if there are no holes prepared for lock installation.
Preparation Remove existing door hardware, latch or deadbolts before installing the new lock. Use provided template to bore new holes if needed. 1 " - 2" (35mm - 50mm) * 1" 2 25mm Measure and confirm your door is 2 Measure and confirm the hole in the 3 Measure and confirm that the backset 4 Measure and confirm that hole in the between 1 door is 2 " - 2" (35mm - 50mm). " (54mm). " 54mm Backset 2 " (60mm) or 2 " (70mm) 1 is between 2 " (60mm) to 2 " (70mm). door edge is 1” (25mm).
Step 1 INSTALLING THE LOCKSET Measure the distance between center of front door hole to the edge of your door and select the correct lockset. Select F1 if 2-3/8"(60mm) or F2 if 2-3/4"(70mm). G 2-3/8" 8" (60mm) m G 2-3/4" (70mm) F1 F2 G G Facing the door exterior, install the lockset according to the opening direction of your door. Out-swing Door In-swing Door OR Secure lockset with provided G screws.
Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS Determine right swing or left swing door While facing the door from the inside, if hinges are on the right side you have the right swinging door. If hinges on the left side you have a left swinging door. The lock ships set for right swing doors. Skip STEP 2 if your door is a right swing door. See steps below to change door handle orientation for a left swing door.
Step 2 continued CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS 5 4 Confirm that your installation was complete by checking if the pins are flush against the handle, and has popped out. Adjust the handle accordingly to make sure the pins are fully decompressed and sits flush against the surface. 6 Check that your handle works smoothly by giving it a turn up and down. Twist key back to horizontal position. The key can be taken out once it goes back to the horizontal position.
Step 2 continued CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS Changing the Interior Handle Orientation 1 2 Securely screw clockwise as shown Remove the screw by turning counter clockwise and rotate the handle 180° in the direction of the arrow as shown. Make sure the screw hole is aligned with the marker as illustrated. to complete your handle orientation change.
Step 3 PREPARING LOCK FOR INSTALLATION If you drilled a hole in Preparation, use Slotted Barrel Extension U and securely tighten with a flat head screwdriver by turning it clockwise onto the lock. If you did not drill a hole in Preparation, you can leave this pole removed. 4 1 2 Peel paper layer OFF the Adhesive tape and prepare for installation. 3 D Install Spindle C with the holes side into the base of the lock and align the holes locate in the 3 o’clock and 9 o’clock position.
Step 4 INSTALLING THE LOCK (EXTERIOR) Exterior 1 Install the exterior lock as shown to the left by aligning the lock straight and passing the cable and attached rods through the lockset. 3 2 Pass the Spindle C through the center of the lockset, and the round rods through the sides in their respective holes. The cable should run underneath the lockset. 10 Align the lock straight and press hard (if you use the Adhesive tape in step 3.4) to secure the top of the lock.
Step 5 INSTALLING THE LOCK (INTERIOR) Interior 1 Insert Positioning Rods V into the holes to the left and right of the Spindle C . The holes are located at the 3 o’clock and 9 o’clock positions. V 2 Mounting Plate LK Interior Mounting Plate LK will go against the interior side of your door. Remove the paper layer off of the Adhesive Tape and align the positioning rods on the bottom of the plate to the corresponding left and right holes. Install the side with the black plastic seal against the door.
Step 5 INSTALLING THE LOCK (INTERIOR) continued Screw O 3 LK Pull the cable from the lock exterior through the rectangular hole underneath the positioning rods and spindle. Secure the hole above the spindle with screws O . *Secure top with M1 or M2 4 O 3x Screw O 12 Remove the position rods V and replace them with screws O Tighten clockwise until the mounting plate is secure.
Step 5 5 INSTALLING THE LOCK (INTERIOR) continued Plug X cable that is coming through the door into the lock interior Y . Match red side of the plug with red on socket insert tightly. X Y NOTE: If you need to disconnect the cable, make sure to press the snap tab to release the plug before carefully pulling it out. Do not force, as this may result in damaging the lock. 6 Align the square rod to the lock interior and attach the Interior lock to the Interior mounting plate.
INSTALLING THE LOCK (INTERIOR) continued 7 P (3X) 8 -+ +- Step 5 Once the lock interior is flush against the mounting plate, secure the lock to the plate by screwing clockwise using provided screws P . Insert 4 AA batteries into the lock by aligning the positive + and negative orientation markings on the batteries to the battery chamber. Secure the battery cover by sliding the cover over the lock and turning the screw clockwise on top until tight.
Step 6 INSTALLING THE DOOR STRIKE Close your door to see if your lock closes securely with your existing door strike. If the lock closes securely, you may keep the existing door strike without removing the old hardware. However, it’s recommended that you use our door strike. G(2X) H DOOR STRIKE INSTALLATION F Make sure the slanted side of Latchbolt ( F1 / F2 ) is closing against the slanted part of Strike Plate H before fixing it on to door frame.
Step 7 DOWNLOAD THE LOCKLY® APP Congratulations! You have completed the LOCKLY Secure physical lock installation. To complete your setup, download the LOCKLY app from the iOS or Google Play app Store and follow on-screen instructions. Scan or visit LOCKLY.
Smart Home Ready SECURE LINK You can add live status monitoring and voice control capabilities to your LOCKLY® Smart Lock with Amazon Alexa or Google Assistant via installing the Secure Link (PGH200) Wi-Fi Hub and Door Sensors (Sold Separately) Know it’s Closed. Wireless Door Sensors No more worries wondering if your door was shut when you locked your door. Included is a set of wireless door sensors that can provide accurate information on the status of your door.
FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
INSTALLATION OVERVIEW & PARTS LIST This lock can be installed for both right swing and left swing doors. The lock ships ready for a right swing door installation. If you wish to change the orientation of the lock for a Left Swing door, follow instructions on Installation Guide (Step 2) or the BILT App (Step 10).
Connect with us @meetLOCKLY | #LOCKLY
Reference installation parts overview foldout.
SECURE We’re here to help! help@LOCKLY.com For the latest version of this manual, please visit the following link: LOCKLY.