LCD-Display (back light) Main switch OFF-SEND-SEARCH Lock Button OPTIONS Richtungsanzeige Button MARK Button SCAN Number display Temperatur Number of burials Altimeter Compass Battery level
Dear winter sports enthusiast, Congratulations on having purchased a PIEPS avalanche rescue beacon ! 100,000 skiers world-wide testify to the quality of this brand, which has been on the market for nearly 30 years. During this time, PIEPS beacons have undergone constant improvement. The device you have chosen is a state-ofthe-art piece of equipment.
Carrying harness The PIEPS DSP can be worn directly on your person using the supplied carrying system. Pass the snap hook of the safety cord through the carry pouch and attach it to the loop on the rear of the pouch (=safest option). Alternatively, the PIEPS DSP can be attached to the belt of your ski trousers via the belt loop, or can be carried in your trouser pocket with or without the protective pouch.
LIGHT 1. PRESS 2.
Battery / switching on / SEND mode The battery compartment is located at the rear of the housing. The safety screw connection can be easily opened and closed using a coin. IMPORTANT: Only use battery type LR03/AAA and always replace all 3 batteries with new ones of the same type. Never use rechargeable batteries and always change all batteries at the same time! Depress the main switch lock and push the main switch to the “SEND“ position. In this mode, the PIEPS DSP will carry out a self-test lasting approx.
Temperature Compass 3 x PRESS Degree - End Meter + Meter - End Altimeter Degree + Bearing compass End
Beacon with OPTION PACK By pressing the OPTION switch three times, you can switch from the SEND mode to the OPTION mode. This enables you to switch between the relevant functions: ! Temperature display Press SCAN to switch between °C and °F. ! Compass When new batteries are inserted, the compass has to undergo an internal calibration. This is also necessary if the device detects strong temperature variations. To start the calibration, press SCAN (”CAL” flashes). Then rotate the device a full 360°.
Single rescue person 50m Point of impact û Point of disapearnce Multiple rescue persons Flow direction 50m
EMERGENCY / SEARCH mode In case of an emergency, the key thing to remember is: KEEP CALM, OBSERVE, RAISE THE ALARM Observe the course of the avalanche and make an exact mental note of where the victim ! was hit by the avalanche (point of impact) ! was last seen (point of disappearance) The extension of these points indicates the flow direction of the avalanche ! The primary search area is to the left and right of this.
SEARCH mode / rough search As soon as the PIEPS DSP picks up signals, the approximate distance and direction appear in the display. The number of victims within the range of the device is represented by matchstick men. Number of burials: one two three four or more Using the arrow and distance reading, follow the strongest of the received signals along the field lines.
SEARCH mode / close search Once you have approached the victim quickly with the rough search, the PIEPS DSP really comes into its own thanks to its advanced triple-antenna system. When you are closer than 3 m to the victim, you can start locating the position point by point. To avoid confusion, the direction display is now suppressed (point 1). Continue moving in the same direction and follow the plan on the left. After a certain point, the distance reading will start to increase again (point 2).
Suppress with MARK Locate third victim Locate second victim Locate first victim Suppress with MARK 3 burials are indicated
SEARCH mode / multiple search The optimised multiple search, the absolute highlight of the PIEPS DSP, is based on a separation of signals via the digital signal processor (DSP). If there are multiple victims, this is clearly indicated by the number of matchstick men. By default, the PIEPS DSP will automatically search for the strongest signal. Once the position of the first victim has been located, press the MARK key for approx. 3 seconds without moving away from this point.
Radius50m Anzeige: 4 od.
SEARCH mode / SCAN function Another highly useful feature of the PIEPS DSP is the SCAN function. Press the SCAN key in the SEARCH mode and the device will begin scanning the entire receiving range. During the scan, stand still and hold the device steady. This will give you an overview of all the victims' devices within the detectable range, classified according to three groups: ! Reading 1: within a distance of approx. 5m ! Reading 2: within a distance of approx.
Technical data Device designation: Transmission frequency: Power supply; Battery lifetimer: Maximum range: Earphone socket: Temperature range: Weight: Dimensions (L xWB X H) PIEPS DSP 457 kHz (internation standard frequency) 3 batteries, Alkaline (AAA), IEC-LR03, 1,5V Min. 200 h in SEND Mode 60 Metres (digital evaluation) Stereo earphone 3,5 mm, min. 32 Ohm -20°C bis +45°C 198 g (incl.
Warranty conditions: The device is guaranteed by the manufacturer against defects in material and workmanship for a period of five years from the date of purchase. This warranty does not apply to damage caused by incorrect use, dropping or dismantling of the device by unauthorised persons. Any further warranty or liability for consequential damage is expressly excluded.