GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 1 iCube ™ www.phonak.com 029-0693-02/V1.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 4 Welcome Congratulations on choosing iCube from Phonak, the first manufacturer to offer you CableFree Fitting. iCube enables the wireless transfer of fitting data from your PC directly to your client’s hearing instruments. Based on Bluetooth technology the fitting process is fast, smooth and stable, and most importantly, cable-free. Please read this manual carefully to benefit from all the features of your iCube.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Description Seite 6 iCube accessories 햲 햳햴햵 햶 햷 • • • • USB cable, 3 m (10 ft.) iCube charger USB Bluetooth adaptor USB hub Contents may vary depending on country.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 8 Getting started Installing and using the iCube charger Charging the battery Install the iCube charger by plugging the power supply into a power outlet and docking iCube into the iCube charger as shown below. Your iCube has an internal, rechargeable battery. As soon as you place your iCube on the iCube charger, the battery starts charging. For safety reasons, recharge the battery only with chargers supplied by Phonak.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 10 Getting started Your iCube battery can be charged hundreds of times. If the operating time of your iCube reduces substantially, please contact your local Phonak representative. Battery status While turned ON, your iCube indicates the battery status on the battery indicator LED as follows: Operating time Battery consumption and the operating time of the iCube greatly depend on the usage of the device.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 12 Getting started Turning iCube ON/OFF Connecting iCube to your computer Turning iCube ON To turn ON your iCube, press and hold the ON/OFF button for about a second until you see the battery indicator turn ON. Once your iCube is fully operational, the battery indicator will flash slowly. iCube was designed to bring you the benefits of CableFree Fitting via Bluetooth connection.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 14 Getting started If you are using NoahLink and you have already installed the corresponding external Bluetooth adaptor, you can use that same adaptor for iCube. If your computer is neither equipped with Bluetooth built in nor with a NoahLink compatible Bluetooth adaptor, use the Bluetooth adaptor accessory provided by Phonak. Refer to the “quick start guide” document available with the adaptor's Software CD and follow the instructions.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 16 Getting started 3. Pairing iCube with your computer Select “Use iCube via Bluetooth” and the pairing wizard will guide you through the process of pairing iCube with your computer. Pairing is necessary to control which Bluetooth devices are permitted to communicate with each other. It needs to be completed only once, before first use.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 18 Getting started Follow the instructions to complete pairing and finish the connection process for iCube. Upon successful completion, the “CableFree Fitting Status” will inform you about the status of iCube: 18 Deleting Bluetooth pairing Please note that only one iCube can be paired with your computer.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 20 Getting started Connecting via USB cable If you wish to connect your iCube via USB cable instead of Bluetooth, start the “Connection Wizard for iCube” in the iPFG fitting application as described on page 14 and choose to use iCube via USB cable. When prompted by the wizard, connect the Mini USB plug of the enclosed USB cable as indicated below. Attach the other end of the cable to a USB socket of your computer.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 22 Using iCube Before using iCube to fit a client with hearing instruments, make sure the battery is sufficiently charged. Remove iCube from the iCube charger and turn it ON. Wearing iCube Open the neckloop by unplugging the jack, and place iCube around your client’s neck as shown below.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 24 Using iCube Continue by selecting to use either the settings from the hearing instruments ("HI") or from iPFG. Now the hearing instruments and iCube are ready for fitting. Programming hearing instruments without clients When programming hearing instruments without having your clients wear them, make sure they are in range of iCube. Place both hearing instruments and iCube as shown in the following picture.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 26 Reset button If, for some reason, iCube becomes unresponsive, remove the cover by sliding it upwards. Then press the reset button as shown in the picture. The Bluetooth pairing will not be lost. If all three indicators on your iCube are lit solid, this may indicate a software problem. Refer to Troubleshooting section.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 30 Indicators Fitting status 30 Red Right fitting status indicator flashing fast. iCube is programming the right hearing instrument. Blue Left fitting status indicator flashing fast. iCube is programming the left hearing instrument.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 32 Indicators Software indicators iCube is built such that it can be upgraded whenever new functionalities are available. Follow the instructions provided together with the new software version. 32 Red / yellow / blue All three indicators flash fast. iCube is being upgraded. Red / yellow / blue All three indicators lit solid. This may indicate a software problem. Refer to Troubleshooting section.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 34 Important information Maintenance and care Clean iCube using a damp cloth. Never use household cleaning products (washing powder, soap, etc.) or alcohol to clean the device. Protect iCube from excessive moisture and heat. Protect it from excessive shock and vibration. When iCube is not in use, turn it OFF and store it in the iCube charger so it will be sufficiently charged and ready for the next fitting session.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 36 Important information The digitally-coded, inductive transmission technology used in this device is extremely reliable and experiences virtually no interference from other devices. It should be noted, however, that when operating the device near a computer terminal or other strong electromagnetic fields, it may be necessary to be at least 60 centimeters (24“) away to ensure proper operation.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 38 Important information Troubleshooting 38 Situation Most probable cause Remedy iCube is no longer recognized by the computer to which it was previously paired. The Bluetooth functionality of your computer may be disabled. Find the Bluetooth settings on your computer and turn Bluetooth functionality ON. iCube is out of range. Move iCube closer to your computer. iCube turns OFF. The battery is empty. Charge iCube.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 40 Declaration of conformity Service and Warranty Phonak AG, Laubisrütistrasse 28, CH-8712 Stäfa, Switzerland declares under its sole responsibility that the iCube is in conformity with the following standards or other standardizing documents: Phonak offers you a comprehensive global warranty which becomes effective on the date of purchase. This warranty covers any repairs due to defects in material and/or workmanship.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 42 Phonak distributors worldwide Group companies: Australia Austria Belgium Brazil Canada China Denmark France Germany Italy Japan Jordan Mexico Netherlands New Zealand Norway Poland Russian Federation 42 (detailed information on www.phonak.com) Phonak Australasia Pty. Ltd. Baulkham Hills N. S. W. 2153 Hansaton Akustische Geräte GmbH 5020 Salzburg Ets Lapperre B.H.A.C.
GA_iCube_GB._AK1_9.10.07.qxp XXXX ! 24.1.2008 14:27 Uhr The CE symbol is confirmation by Phonak AG that this Phonak product meets the requirements of directive 93/42/EEC on medical devices and the R&TTE Directive 1999/5/EC on Radio and Telecommunication Terminal Equipment. The numbers after the CE symbol are the numbers of consulted certified bodies under the above mentioned directives. The alert sign means that potential restrictions on its use are applicable in one or more EU Member States.
GA_iCube_GB._AK1_9.10.07.qxp 24.1.2008 14:27 Uhr Seite 46 Notices Notice 1 This instrument is certified under: FCC ID: KWC-ICUBE1 IC: 2262A-ICUBE1 This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.