• Verify the positive lead and ground of cart. When routing the Power Harness cable make sure the cable does not interfere with cart operation. The cable should be isolated of working parts of the cart. Two installers are required to remove seat to avoid back injuries. • • • Parts Required for Assembly of Power Supply Bracket and Mounting Power Supply 1. 2. 3. 1 4. 5.
Future picture of power supply mounted on bracket 3. Mount Power Supply onto bracket using four bolts. Note: Power Supply connector should be facing towards beveled end of power supply bracket. Club Car Power Harness Installation Parts 1. 2. 3.
Future Picture of Club Car Cart with completed Power Harness Installed
Club Car Power Harness Installation
Note: Two Persons Should be used to Remove Seat. 1. Remove Seat Note: Be Careful of Battery Acid Build up Around Battery Terminals Note: Frame Ground- Do Not Allow tools to contact from when disengaging battery cable. Never allow a Positive wire to touch the cart frame. 2. Remove Nut on Positive Terminal Lead of battery 3. Attach the Red Ring terminal of power harness to battery 4. Secure the nut back onto Positive Terminal Lead of the battery 5.
installing black wire power harness Future Supply location on Club Car. Futurepicture pictureof ofPower seat being Future picture of installing redremoved wire ofof power harness Future picture of power supply being connected to power harness. compartment, in front of batteries.
12. Install blue wire to electrical system for key switch. MORE to ADD Mike C. 13. Route Power Harness cable along frame of cart. Securing with tie straps. Note: The cable should be isolated of working parts of the cart. 14. Replace the Seat 15. Remove screw caps on the side of dashboard, and save 16. Loosen screws securing dashboard 17. Pop off top of dashboard by running screwdriver along the top of dash and below frame of cart 18.
picture cable. A.Future Remove cap depicturingC.route Insertofscrewdriver here to remove dash. B. Loosen screw D. Run screwdriver along white line C. Remove cap D. Loosen screw 21. Insert bottom of dashboard back into place Note: BE CAREFUL NOT TO ALLOW THE KEYSWITCH TO COME IN CONTACT WITH THE CART FRAME. 22. Pull about 1’ 6” of cable out to be ran for the Display Unit 23. Bend right corner inward to allow key switch room to be inserted 24. Place left corner in place 25.
EZ-GO Power Harness Installation Parts Future picture of Power harness, Power supply bracket, clamp, Phillips head screw, and four bolts. 1. 2. 3.
Future Picture of Club Car Cart with completed Power Harness Installed
EZ-GO Power Harness Installation Process has not been defined at this time.
Yamaha Power Harness Installation Parts Future picture of Power harness, Power supply bracket, clamp, Phillips head screw, and four bolts. 1. 2. 3.
Future Picture of Club Car Cart with completed Power Harness Installed
Yamaha Power Harness Installation Process has not been defined at this time.
Overview of Generic Display Unit Bracket Installation • Left (drivers side) and Right side of cart will be identified as someone sitting forward in cart. Make sure key switch is in the off position. Ensure the parking brake is set. When routing the Power Harness cable make sure the cable does not interfere with cart operation. The cable should be isolated of working parts of the cart. • • • • Specific Display Unit Bracket Installation instructions per cart type ex.
Future picture of completed Display Unit Bracket Installation.
Club Car Display Unit Bracket Installation Future power harness cable into display unit support cover removed Future picture picture of of routing re-installing mounting bracket display onunit cart. center piece. bracket 1. Remove four Screws securing the Display Unit Support Cover 2. Install Mounting Bracket on left side of cart 3. Run Power Harness cable behind mounting bracket and into hole in center piece 4. Re-Install Display Unit Center Piece.
EZ-GO Display Unit Bracket Installation Parts Future picture of Display Unit bracket with call outs.
Future picture of completed Display Unit Bracket Installation.
EZ-GO Display Unit Bracket Installation Future picture of EZ-GO Display Unit Bracket Installation. Process has not been defined.
Yamaha Display Unit Bracket Installation Parts Future picture of Display Unit bracket with call outs.
Future picture of completed Display Unit Bracket Installation.
Yamaha Display Unit Bracket Installation Future picture of Yamaha Display Unit Bracket Installation. Process has not been defined.
Overview of Generic Display Unit Installation • Left (drivers side)and Right side of cart will be identified as someone sitting forward in cart. Make sure key switch is in the off position. Ensure the parking brake is set. When routing the Power Harness cable make sure the cable does not interfere with cart operation. The cable should be isolated of working parts of the cart. Use caution when installing the UHF and GPS connectors to the Display Unit.
Future picture of Display unit completely installed Club Car Display Unit Installation Future picture attaching UHF Connector to Display Unit 1. Attach UHFofConnector to Display Unit 2. Attach GPS Connector to Display Unit 3. Connect Power Harness to GPS Connector to Display Unit Future pictureconnector of attaching Display Unit 4.
EZ-GO Display Unit Installation Parts Future picture of display unit with screws 1. 2.
EZ-GO Display Unit Installation Future picture of Display unit completely installed
EZ-GO Display Unit Installation Process has not been defined
Yamaha Display Unit Installation Parts Future picture of display unit with screws 1. 2.
Future picture of Display unit completely installed
Yamaha Display Unit Installation Process has not been defined