Data Sheet / User Manual RB-TW-2400 Data Sheet / User Manual Radio Module RB-TW-2400 © PHOENIX CONTACT - 08/2012 DataUserManual FCC_05.
Data Sheet / User Manual DataUserManual FCC_05.
Data Sheet / User Manual 1 1 Table of Content Table of Content.............................................................................................................................. 3 1.1 2 3 4 5 RB-TW-2400 Introduction............................................................................................................................. 5 Electrical Interface and Connectors ................................................................................................ 5 2.
Data Sheet / User Manual 6 7 RB-TW-2400 FCC and IC Compliance for 9059446 ............................................................................................. 26 6.1 FCC Statement for 9059446 .................................................................................................. 26 6.2 Antenna ................................................................................................................................. 26 6.3 Caution ...........................................
Data Sheet / User Manual RB-TW-2400 1.1 Introduction The hardware with the PCB identifier 9054212_01 and the module is Type Approved with the type name RB-TW-2400. The radio module RB-TW-2400 is a radio platform with an implemented radio stack, named Trusted Wireless (TW). TW is a proprietary network with a frequency hopping technology. 2 Electrical Interface and Connectors This section describes the signals available on the module interface connectors. 2.
Data Sheet / User Manual RB-TW-2400 5 VCC Power PWR 3.7-6.0VDC Power supply 6 GND Power PWR Power GND 7 VCC Power PWR 3.7-6.0VDC Power supply 8 GND Power PWR Power GND 9 VCC Power PWR 3.7-6.0VDC Power supply 10 GND Power PWR Power GND 11 VCC Power PWR 3.7-6.0VDC Power supply 12 GND Power PWR Power GND 13 NC 14 Power ON/OFF IN Set Open/Low, pin is internally pulledup with 10kOhm.
Data Sheet / User Manual RB-TW-2400 28 UART GND Digital GND GND GND Digital 29 UART API TX OUT API Comminunication interface 30 GND Digital GND GND GND Digital 3152 for internal use NC NC 2.3 Characteristics 2.3.1 Power supply Signal Name Parameter VCC Power Power Supply Value Unit min 3.7 V DC max 6.0 V DC The module is equipped with Step Down Converter. 2.3.2 Current consumption Signal Name Parameter Vcc Power Icc @ VccPowe = 5.
Data Sheet / User Manual RB-TW-2400 2.3.4 Environmental Temperatures characteristics Parameter Storage temperature Operating temperature 3 Value Unit min - 40 °C max + 85 °C min - 40 °C max + 80 °C Antennas This chapter gives a quality overview of the different antenna options. On the Boards itself the RF interface is an U.FL. connector for external antennas. Different types of external antennas are available. 3.1 Antenna Accessories Part Number 0138498 Name U.
Data Sheet / User Manual Part Number 2701402 Name RAD-PIG-EF316-N-RSMA Connector RSMA (male) and N (female) Cable length 0,5m Cable loss 0,75 dB Part Number 2867694 Name RAD-PIG-EF316-N-SMA Connector SMA (male) and N (female) Cable length 0,3m Cable loss 1,5 dB/m DataUserManual FCC_05.
Data Sheet / User Manual Part Number 2903263 2903264 2903265 2903266 Name RAD-PIG-RSMA/N -0,5 -1 -2 -3 Connector RSMA (male) and N (male) Cable length 0,5m 1m 2m 3m Cable loss TBD dB/m Part Number 2867649 2867652 2867665 2885634 Name RAD-CAB-EF393- 3M -5M -10M -15M Connector N (male) / N (male) Cable length 3m 5m 10m 15m DataUserManual FCC_05.
Data Sheet / User Manual Cable loss 0,45 dB/m Part Number 2884512 2884525 Name RAD-CAB-EF142-3M Connector SMA (male) / SMA (male) Cable length 3m 5m Cable loss 0,93 dB/m RB-TW-2400 3.2 Recommended antennas Part Number 2701362 Name RAD-ISM-2400-ANT-OMNI-2-1RSMA Polarization Vertical Gain +2.0dBi Cable lenght 150cm DataUserManual FCC_05.
Data Sheet / User Manual Size 82,5 / 7,8mm Connector RSMA Part Number 2701358 Name RAD-ISM-2400-ANT-VAN-3-0RSMA Polarization Vertical Gain +3.0dBi Cable lenght 150cm RB-TW-2400 Size Connector RSMA 3.3 Recommended antennas professional use Part Number 2692526 Name RAD-ISM-2459-ANT-FOOD-6-0 DataUserManual FCC_05.
Data Sheet / User Manual Polarization Vertical Gain +6dBi Cable lenght 100cm N(m) SMA(m) RB-TW-2400 Size Connector N- (female) Part Number 2885919 Name RAD-ISM-2400-ANT-OMNI-6-0 Polarization Vertical Gain +6dBi Cable lenght -- DataUserManual FCC_05.
Data Sheet / User Manual Size 250 /22 mm Connector N- (female) DataUserManual FCC_05.
Data Sheet / User Manual Part Number 2903219 Name RAD-ISM-2400-ANT-OMNI-6-0SW Polarization Vertical Gain +6dBi Cable lenght -- RB-TW-2400 Size Connector N- (female) Part Number 2867623 Name RAD-ISM-2400-ANT-OMNI-9-0 Polarization Vertical Gain +9dBi Cable lenght -- DataUserManual FCC_05.
Data Sheet / User Manual RB-TW-2400 Size Connector N- (female) Part Number 2867610 Name RAD-ISM-2400-ANT-PAN-8-0 Polarization Gain +8dBi Cable lenght -- Size (height x width x depth) Connector 102 mm x 95 mm x 32 mm SMA- (female) DataUserManual FCC_05.
Data Sheet / User Manual 4 RB-TW-2400 Mechanics 4.1 Module Outlines Dimensions DataUserManual FCC_05.
Data Sheet / User Manual RB-TW-2400 4.2 Connector The connector has 52 contacts and is compatible with PCI Express Mini Card elect mechanical specification. DataUserManual FCC_05.
Data Sheet / User Manual 5 RB-TW-2400 Operation 5.1 Overview The API module’s job is it to serve the interface to external devices (in most cases this is the Application Controller (AC). It provides a set of commands available for the external device (hereinafter referred to as AC). 5.2 Communication Interface The RC provides two communication interfaces which can be selected by the user. These two interfaces are mutually exclusive and must be selected by the user before boot up.
Data Sheet / User Manual RB-TW-2400 5.2.1 Communication Cycles (SPI) Communication on the SPI-Interface only takes place if the ready line is set by the RC. With this line, the RC can control, when the AC is allowed to transmit/receive data. This is necessary for example, to process commands on the RC correctly. A communication cycle can only be initiated by the SPI master, when the ready line is set. In this case the AC can always transmit 7 Byte (A command of 5 Bytes and 2 Byte CRC Check) to the RC.
Data Sheet / User Manual RB-TW-2400 There are AC initiated API commands without response (not further Data-Transfer required). In this case, the indication line as shown in figure 2 will not occur. RC initiated communication Also the RC can trigger a communication cycle as shown in fig. 3. This is done by setting the indication-line. On this indication (or Request) the AC is reading 5+2 Bytes, the Command Bytes. After the transfer of this 7 Bytes, the AC and or RC may have to prepare the DMAs.
Data Sheet / User Manual RB-TW-2400 5.3 Operation In order to operate the RC it needs a valid configuration. A default configuration is loaded at boot up, nevertheless a unique node ID must be configured after every boot up. After the RC was configured it is ready to be started by the user, this is done by setting the RC to normal operation mode. During normal operation the RC is ready for application message exchange. 5.
Data Sheet / User Manual RB-TW-2400 The parameter address high and low bytes are used to address the parameter which should be read or written to. A table with parameter addresses is shown in the next subsection. The data field is used optionally. It can be utilized for parameter values which have a length of only one byte. In order to use this field for parameter data the length value has to be set to ‘0’. In readrequests and write-responses it is ignored.
Data Sheet / User Manual RB-TW-2400 Default Configuration The default configuration is loaded during boot up. It may be changed to the suite the users needs. The node ID is set to invalid, so the user has to change it. Parameter Value Node ID 255 (=invalid) Repeat 3 OTA Datarate 4 (=250 kBaud) NetType 0 (=Mesh) Network ID 127 Retries 3 (=2 Retries) TX-Power 20 dBm LNA Enables 1 (=enabled) RF-Band 1 5.4.
Data Sheet / User Manual RB-TW-2400 5.4.2 Application Message Exchange This command is used to exchange application data with the RC.
Data Sheet / User Manual 6 RB-TW-2400 FCC and IC Compliance for RB-TW-2400 6.1 FCC Statement for RB-TW-2400 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Data Sheet / User Manual RB-TW-2400 The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's website www.hc-sc.gc.
Data Sheet / User Manual RB-TW-2400 to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC ID label must be displayed on the device. In case, where the final product will be installed in locations where the end-user is not able to see the FCC ID and/or this statement, the FCC ID and the statement shall also be included in the end-product manual. 6.
Data Sheet / User Manual RB-TW-2400 • Do not attempt to disassemble your product. Doing so will void warranty. The product does not contain consumer serviceable or replaceable components. Service should only be performed by Phoenix Contact. • Do not paint your product as the paint could prevent normal use. • If you will not be using your product for a while, store it in a place that is dry, free from damp, dust and extreme heat and cold.
Data Sheet / User Manual RB-TW-2400 • Connect your power supply only to designated power-sources as marked on the product. • Make sure all cords and cable are positioned so that they will not be stepped on, tripped over or otherwise subject to damage orstress. • To reduce risk of electric shock, unplug the unit from any power source before attempting to clean it. DataUserManual FCC_05.
