User's Manual

ManualsBrandsPhilips Electronics Industries ManualsComputers & Accessories19 Inches Color Monitor

Product Information

Product Features • LightFrame™ for Windows •Technical Specifications • Automatic

Power Saving • Physical Specification • Pin Assignment • Product Views

Product Features

109B40/109B43:



19-inch (18.0" VIS) Real Flat color monitor with excellent front of screen performance for use

with MACs and PCs



Autoscan covers horizontal frequencies up to 90 kHz offering a maximum resolution of 1920 x

1440 with flicker free display of 1280 x 1024 at up to 91 Hz



Real Flat High Contrast CRT with high-resolution 0.25 mm dot pitch (0.21 hdp)



LightFrame™ for brightest and sharpest display of movie and photo windows



XSD-Xtra Space Design for large screen display in a small footprint: World's shortest 19" Real

Flat shadow mask monitor with maximum depth of only 449 mm/17.6" that matches most of

today's 19-inch monitors



Multimedia Base and USB Hub option



sRGB for true on screen color representation.



FCC, CE (in selected countries only) and ISO9241, ISO14001 certified

RETURN TO TOP OF THE PAGE

LightFrame™ for Windows

Introduction

Philips LightFrame™ feature enriches the experience of pictures and video on a Philips CRT (picture

tube) monitor. LightFrame™ will boost the brightness and sharpness of photos and videos on the

monitor screen.

To control the LightFrame™ feature in your monitor, you have to install the LightFrame™ application

which you will find on this CD-ROM.

Note

Philips LightFrame™ will only work with monitors that have been built to use this software. Earlier

Philips monitors or other manufacturers’ monitors will not work with this special software. It is

recommended that you install this software only on a Philips monitor designed to use it. These monitors

can be identified by the LightFrame™ logo on the front of the monitor.

This software is not designed for use with LCD flat screen monitors.

LightFrame™ will work with true Windows-based programs and DOS-based programs that operate in a

Windows environment. It will not work with DOS-based programs operating only in a DOS environment.

Language Selection

Exhibit 3

Installstion and Operating Instructions

Summary of content (15 pages)

PAGE 1
Exhibit 3 Installstion and Operating Instructions Product Information Product Features • LightFrame™ for Windows •Technical Specifications • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Product Features 109B40/109B43: 19-inch (18.
PAGE 2
While English is the default language of LightFrame™, the User Interface can be set up to operate in Dutch, French, German, Italian, Portuguese, Spanish, Simplified Chinese, Traditional Chinese or Korean. Installation 1) To install LightFrame™, place the CD in the CD-ROM drive. 2) Next, when the menu of items on the CD appears on your screen, click on 'Install LightFrame™'. 3) Now, follow the on-screen prompts to properly install the program. The software checks to see if you have a compatible monitor.
PAGE 3
Q: How do I use the LightFrame™ 3 control bar that appears at the top my screen? A: The control bar is another upgrade that helps you run all LightFrame™ 3’s neat, new features. The illustration below describes the tasks each button performs. Accustomed to working with the original LightFrame™ tray icon? No problem: It’s still there and can be used to turn LightFrame™ on or off and check LightFrame™ status.
PAGE 4
SCANNING • Horizontal scanning 30 - 97 KHz • Vertical scanning 50 - 160 Hz VIDEO • Video dot rate 203 MHz • Input impedance - Video 75 ohm - Sync 2.2 kOhm • Input signal levels 0.7 Vpp Separate sync • Sync input signal Composite sync • Sync polarities Positive and negative WHITE COLOR TEMPERATURE Chromaticity CIE coordinates: • at 9300 K degrees x = 0.283 / y = 0.297 • at 6500 K degrees x = 0.313 / y = 0.329 • at 5500 K degrees x = 0.332 / y = 0.
PAGE 5
Automatic Power Saving If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. And if an input from a keyboard, mouse or other input device is detected, the monitor will automatically "wake up".
PAGE 6
The 15-pin D-sub connector (male) of the signal cable (IBM systems): Pin Assignment No. Pin Assignment No. 1 Red video input 9 No pin 2 Green video input 10 Logic ground 3 Blue video input 11 Identical output connected to pin 10 4 Identical output connected to pin 10 12 Serial data line (SDA) 5 Ground 13 H. Sync / H+V 6 Red video ground 14 V.
PAGE 7
Installing your Monitor Front View • Rear View • 6G3B11 Multimedia Base (option) • PCUH411 USB Hub (option) Front View Power button switches your monitor on. OK button which when pressed will take you to the OSD controls Contrast hotkey. When the UP arrow is pressed, the adjustment controls for the CONTRAST will show up. UP and DOWN buttons are used when adjusting the OSD of your monitor Brightness hotkey. When the RIGHT arrow is pressed, the adjustment controls for BRIGHTNESS will show up.
PAGE 8
RETURN TO TOP OF THE PAGE Rear View 1. Power in - attach power cable here. 2. Video In - this is a cable which is already attached to your monitor. Connect the other end of the cable to your PC.
PAGE 9
Regulatory Information TCO '99 Information • TCO Environmental Requirements • CE Declaration of Conformity • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S.
PAGE 10
Energy Star Declaration PHILIPS 109B4* This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling (DPMS) standard. This means that the monitor must be connected to a computer which supports VESA DPMS to fulfill the requirements in the NUTEK specification 803299/94. Time settings are adjusted from the system unit by software. From indicated inactivity to Power Saving Position A2, the total time must not be set to more than 70 minutes.
PAGE 11
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device. To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture. THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
PAGE 12
Exhibit 4 The brief ckt. description of M40 109B4/109S4/107P4” Monitor 0. Functional Block Diagram 1. General Description 2. Description of Circuit Diagram A. Power Supply B. Horizontal Deflection/Vertical Deflection/EHT Generator C. Video board D. H / V convergence control E.
PAGE 13
1. GENERAL DESCRIPTION The M40 platform includes 109B4 using 19” flat shadow mask CRT, 109S4 using 19”convention CRT and 107P4 using 17” flat CRT, they are so-called “Digital Controlled Auto-scan Color Display Monitor” with high resolution which can operate at horizontal scan frequency from 30kHz up to 97KHz, 92KHz and 92KHz for109B4, 109S4 and 107P4 respectively, and vertical scan frequencies can operate from 50 to 160 Hz.
PAGE 14
This controller provides sync processing, which can accept separate input signals, a very short settling time after mode change for protection of external power components has been taken into account.
PAGE 15
The convergence coils are combined with deflection yoke, they are also driven by DC amplifiers. Via OSD menu, two control functions H-convergence and V-convergence can be selected to adjust the convergence of CRT by using digital control. E.