Instructions / Assembly

ManualsBrandsPhilips Bodine ManualsCeiling Light Parts120-Volt to 277-Volt ELI-S-100 100-Watt Sinusoidal Emergency Lighting Inverter

Installation and Operation Instructions

ELI-S-100

WITH AUTO-DIMMING FEATURE

ELI SERIES EMERGENCY LIGHTING INVERTERS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

! IMPORTANT SAFEGUARDS !

WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY

PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,

INCLUDING THE FOLLOWING:

SAVE THESE INSTRUCTIONS

1. Caution:

• High voltage will be present on the output wires and terminals if batteries are installed and inverter

connector is joined or if AC power is supplied to the switched and unswitched terminal.

• Ensure input and output primary wiring connections are made to the proper terminals. Damage to product

may occur if miswired.

• Ensure load voltage requirements (120 or 277 Vac) match the output ratings of this product or damage to

the load devices may occur.

2. This product is suitable for use in dry and damp locations where the ambient temperature is 0°C through

40°C, depending on load. See output ratings on product label for details. This product is not suitable for

heated air outlets and wet or hazardous locations.

3. Make sure all connections are in accordance with the National Electrical Code or Canadian Electrical Code

and any local regulations.

4. To reduce the risk of electric shock, disconnect both the normal and emergency power supplies and the

inverter connector of the emergency lighting inverter before servicing.

5. Do not install near gas or electric heaters.

6. An unswitched AC power source is required. The AC voltage rating of this equipment is speciﬁed on the

product label. Do not connect equipment to any other voltage.

7. Equipment should be mounted securely in locations and at heights where it will not be readily subjected to

tampering by unauthorized personnel.

8. The use of accessory equipment and replacement parts not recommended by the manufacturer may cause an

unsafe condition.

9. Do not use this equipment for other than its intended purposes.

10. The battery is ﬁeld replaceable. Contact manufacturer for information on replacement. Use caution when

replacing battery. Dispose of the battery properly. Do not incinerate.

THIS PRODUCT INCLUDES RECHARGEABLE LEAD-ACID BATTERIES.

THE BATTERIES MUST BE RECYCLED OR DISPOSED OF PROPERLY.

236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-853-5009 • www.bodine.com

81000092

11/27/18

Summary of content (6 pages)

PAGE 1
ELI-S-100 WITH AUTO-DIMMING FEATURE Installation and Operation Instructions ELI SERIES EMERGENCY LIGHTING INVERTERS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: ! IMPORTANT SAFEGUARDS ! READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. Caution: • High voltage will be present on the output wires and terminals if batteries are installed and inverter connector is joined or if AC power is supplied to the switched and unswitched terminal.
PAGE 2
INSTALLATION WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON THE AC OUTPUT LEADS (HOT AND NEUTRAL) PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN. JOIN INVERTER CONNECTOR INSIDE THE CASE AFTER INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. NOTE: Make sure the inverter connector is closed before screwing the front cover to the case.
PAGE 3
INSTALLATION ILLUSTRATION 2 PRIMARY WIRING CONNECTIONS UnSwHot SwHot COM GND OutHot OutCom TB3 ENCLOSURE GROUNDING LOAD NEUTRAL LOAD HOT SAFETY GROUND NEUTRAL SWITCH LINE HOT CONSTANT HOT OUTPUT CONNECTIONS AC POWER SOURCE INPUT CAUTION: • Unswitched and switched AC power must be fed from the same branch circuit. • Ensure input and output primary wiring connections are made to the proper terminals. Damage to product may occur if wired incorrectly.
PAGE 4
INSTALLATION BATTERY REPLACEMENT To replace the batteries, disconnect both switched and unswitched AC power to the emergency lighting inverter. Remove the two screws securing the lid to the enclosure base and remove the lid. Open the inverter connector wires and then unplug and remove the old batteries. Reverse this process to install the new batteries. Remember to join the inverter connector prior to reinstalling the lid.
PAGE 5
INSTALLATION STEP #6 JOIN THE INVERTER CONNECTOR & APPLY POWER > After installation is complete, apply AC power and join the inverter connector inside the case then screw the front cover to the case. > Note: The inverter has a safety lockout feature that pervents AC output in emergency mode until AC mains power is connected and then lost.
PAGE 6
INSTALLATION Battery: The battery supplied with this equipment requires no maintenance. However, it should be tested periodically and replaced whenever it will no longer operate the connected fixtures for the duration of a 90-minute test. The battery supplied has a life expectancy of four (4) years when used in normal ambient temperature of 72°F. Fuse: The fuse contained within this product is field replaceable. For fuse location see Illustration 1.