User Instructions

ManualsBrandsPhilio Technology ManualsElectronicsSlim Multi-sensor

Slim Multi-sensor PST07

The multi sensor is a Z-WaveTM enabled device which is fully

compatible with any Z-WaveTM enabled network. This device is a

security enabled Z-Wave Plus product that is able to use encrypted Z-

Wave Plus messages to communicate to other security enabled Z-

Wave Plus products. Z-WaveTM enabled devices displaying the Z-

WaveTM logo can also be used with it regardless of the manufacturer,

and ours can also be used in other manufacturer’s Z-WaveTM enabled

networks.

The product supports Over The Air(OTA) feature for the products

firmware upgrade.

This product can be included and operated in any Z-Wave

network

with other Z-Wave

certified devices from other manufacturers and/or

other applications. All non-battery operated nodes within the network

will act as repeaters regardless of vendor to increase reliability of the

network.

The device adopt the Z-Wave

500 series chip, when your Z-Wave

network system is all made by Z-Wave

500 series devices. The

network system will have the advantages as below.

• Concurrent multi-channel support reduces external interference.

Add to/Remove from Z-Wave

Network

There are two tamper keys in the device, one is in the back side,

another is in the front side. Both of them can add, remove, reset or

association from Z-Wave

network.

The table below lists an operation summary of basic Z-Wave functions.

Please refer

to the instructions for your Z-WaveTM Certificated Primary Controller to

access the

Setup function, and to Add/Remove/associate devices

Notice: Including a node ID allocated by Z-Wave

Controller means

“Add” or “Inclusion”. Excluding a node ID allocated by Z-Wave

Controller means “Remove” or “Exclusion”.

Function

Description

Add

1. Have Z-Wave

Controller entered inclusion mode.

2. Pressing tamper key three times within 2 seconds

to enter the inclusion mode.

3. After add successful, the device will wake to

receive the setting command from Z-Wave

Controller about 20 seconds.

Remove

1. Have Z-Wave

Controller entered exclusion mode.

2. Pressing tamper key three times within 2 seconds

to enter the exclusion mode.

Node ID has been excluded.

Summary of content (11 pages)

PAGE 1
Slim Multi-sensor PST07 • Concurrent multi-channel support reduces external interference. Add to/Remove from Z-WaveTM Network There are two tamper keys in the device, one is in the back side, another is in the front side. Both of them can add, remove, reset or association from Z-WaveTM network. The table below lists an operation summary of basic Z-Wave functions.
PAGE 2
Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable. 1. Pressing button four times and keep about 5 seconds. 2. IDs are excluded and all settings will reset to factory default. Reset If the user want to wake-up the device immediately, please remove the front cover, and press the tamper key once. The device will wake-up 10 seconds.
PAGE 3
configuration NO.18 to 0. In the default, when the temperature is changed to plus or minus one degree Fahrenheit (0.5 degree Celsius), the device will report temperature information to the nodes in the group 1. Caution 1: Enable this functionality, it will cause the PIR Motion to disable detection when the temperature measurement. In other words, The PIR motion will blind one second in every one minute. Temperature report: Every 6 hours report once in default.
PAGE 4
COMMAND_CLASS_NOTIFICATION_V8 COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4 COMMAND_CLASS_BATTERY COMMAND_CLASS_SENSOR_MULTILEVEL_V11 COMMAND_CLASS_WAKE_UP_V2 seconds. In the “Normal Mode”, it according to the setting of the configuration NO. 12. Choosing a Suitable Location 1. The recommended mounting height is 160cm 2. Don't let the device facing the window or the sunlight. 3. Don't let the device facing the source of heat. For instance, the heater or the air-condition.
PAGE 5
Z-Wave Configuration Settings Notice: * All of the configuration, the data size is 1. * The configuration mark with star(*), means after the remove the setting still keep, don't reset to factory default. Unless the user execute the “RESET” procedure. * The reserve bit or not supported bit is allowed any value, but no effect.
PAGE 6
N O. 1 Name Basic Set Level 3 PIR (*) Sensitivity 4 LightSensor Threshold line 1 Def . 0x FF 80 1 N O. Valid Description All Setting the BASIC command value to turn on the light. The 0xFF(-1) means turn on the light. For dimmer equipment 1 to 100 means the light strength. 0 means turn off the light. Caution: The value is unsigned byte, the range is from 0x00 ~ 0xFF. Name Def . Valid Description detected function. And always turn on the light.
PAGE 7
N O. Name Def . Valid N O. Description Name Def . Valid detected function. And always turn on the light. LightSensor 8 Threshold line 5 5 1 9 Operation (*) Mode 10 (*) Mult-Sensor Function Switch byte, the range is from 0x00 ~ 0xFF. 0 means turn off illumination detected function. And never turn on the light. 1 means darkest. (500Lux) 1 ~ 100 99 means brightest. 100 means turn off illumination detected function. And always turn on the light. All Operation mode. Using bit to control.
PAGE 8
N O. Name Def . 0 PIR Re12 Detect Interval Time Turn Off Light 13 Time 6 6 Valid Name Def . Valid Bit7: Reserve. After turn on the lighting, setting the delay time to turn off the lighting when the PIR motion is not 1 ~ 60 detected. 10 seconds per tick, default tick is 6 (60 seconds). 0 means never send turn off light command. Auto Report Battery Time 15 Auto Report LightSensor Time 12 0 ~ 127 The interval time for auto report the illumination.
PAGE 9
N O. Name Def . Valid N O. Description Name Def . some issue please see the detail in the “Temperature Report” section. LightSensor 19 Differential Report Temperature 20 Threshold line 1 20 Temperature 21 Threshold line 2 25 Temperature 22 Threshold line 3 30 - 20 ~ 50C 35 - 20 ~ 50C Temperature 23 Threshold line 4 Temperature 24 Threshold line 5 25 PIR Trigger Mode 40 1 - 20 ~ 50C - 20 ~ 50C 1~3 Description Mode3: AtNight The LightSensor Differential to report.
PAGE 10
Transport Service 2 None Battery 1 Highest granted Security Class Sensor multilevel 11 Highest granted Security Class Wake up 2 Highest granted Security Class Specifications subject to change without notice due to continuing product improvement. Disposal This marking indicates that this product should not be disposed with other household wastes throughout the EU.
PAGE 11
the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules.