User's Manual

ManualsBrandsPhilio Technology ManualsElectronicsSmart Color Button

PSR04 Smart Color Button

This round device is a flexible and multi functions button switch. It is able to

switch the appliances on/off or activate the scenes and macros which are preset

already. The rotation sensor make it possible to adjust the percentage of dimmer

or thermostat. It can also work as a timer. The well designed wall bracket and

magnetic back let the switch can be fixed on the wall, Plus

enabled device

and is fully compatible with any Z-Wave

enabled network.

Note:

Please provide a 5 DVC voltage to wake the device up before the

first using.

The rotation function and timer functions work only when the

device is fitted upright or stick on the wall or the device will

only work as an on/off switch when fitted horizontal.

LED indicators

1. LED type and locations

There are two sets of LED embedded in the device.

A. Set 1: Two full color LED lights round the device.

B. Set 2: One red LED under the arrowhead on at the front side.

2. Low battery

The device will enter low battery mode when the battery power is under

20%. The red LED flashes three times every one minute.

3. NWI Auto Inclusion

The red LED will flash quickly for 30 seconds when device entering in NWI

mode.

4. Percentage adjustment mode

The full color LED will turn from green to red according to the percentage

from 0% to 100%. (shown in Fig 3.)

5. Timer mode

A. The red LED will flash once when device entering/exiting the timer

mode..

B. The full color LED will flash once every 10 seconds and the color will

depend on time table (shown in Fig 3.)

Red LED

Full Color LED 2

Full Color LED 1

Touch Button

Fig. 1 Assembling

Summary of content (5 pages)

PAGE 1
PSR04 Smart Color Button This round device is a flexible and multi functions button switch. It is able to switch the appliances on/off or activate the scenes and macros which are preset already. The rotation sensor make it possible to adjust the percentage of dimmer or thermostat. It can also work as a timer. The well designed wall bracket and TM magnetic back let the switch can be fixed on the wall, Plus enabled device TM and is fully compatible with any Z-Wave enabled network.
PAGE 2
C. D. E. The full color LED will flash once with pink every 10 second when countdown from 30. The full color LED will flash with pink light every 1 second when countdown from 5. The red LED will flash 6 times with white when time’s up. D Z-Wave Network Setting Up There is a touch button on the front side. The button carry out inclusion, exclusion and reset to default. C 1. Include: Pointing the arrowhead to area A first (shown in Fig. 2). Pressing the button three times within 1.5 seconds.
PAGE 3
Timer Class, it can receives the updated firmware image sent by controller via the Z-wave RF media. It is a helpful and convenient way to improve some function if 1. Entering the timer mode: A. Pointing the arrowhead to area A. B. Pressing and hold the button about three to five seconds. The red LED will light then go out. Release the button when the light goes out and the buzzer will sound long beep once. needed. 2.
PAGE 4
Troubleshooting Disposal Symptom Cause of Failure The Switch not working and 1. Battery dead LED off 2. Device break Can not adjust the percentage of dimmer or thermostat The device can not join to Z-Wave network Button no response The device may not be placed upright. The device may has joined to a network. The button will no response when LED is flashing This marking indicates that this product should not be disposed with other household wastes throughout the EU.
PAGE 5
• Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.