User's Manual

ManualsBrandsPhilio Technology ManualsElectronicsZ-Wave Remote

Z-Wave Keyfob PSR03- A

Z-Wave Scene Remote PSR03- B

Z-Wave Panic PSR03- C

PSR03- A PSR03- B PSR03- C

The Remote PSR03 is a simple control can control AV device through Z-

Wave-to-IR extender, and it can also controls 8 lighting groups ON/OFF

via basic set, based on Z-Wave

technology.

It is the Z-Wave

plus product, it support the security, OTA... Those

newest features of the Z-Wave

technology. Z-Wave

is a wireless

communication protocol designed for home automation, specifically to

remotely control applications in residential and light commercial

environments. The technology uses a low-power RF radio embedded or

retrofitted into home electronics devices and systems, such as lighting,

home access control, entertainment systems and household appliances.

This product can be included and operated in any Z-Wave

network

with other Z-Wave

certified devices from other manufacturers and/or

other applications. All non-battery operated nodes within the network

will act as repeaters regardless of vendor to increase reliability of the

network.

The device adopts the Z-Wave

500 series chip, when your Z-Wave

network system is all made by Z-Wave

500 series devices. The

network system will have the advantages as below.

• Concurrent multi-channel support reduces external interference.

• Better RF range, improve about 10 meters in indoor.

• Support 100 Kbps transmit speed, speed up communication.

Function Compare A/B/C

Group

Control

Lock

Control

Panic

PSR03-XA V V

PSR03-XB V V V

PSR03-XC V

Summary of content (8 pages)

PAGE 1
Z-Wave Keyfob PSR03- A Z-Wave Scene Remote PSR03- B Z-Wave Panic PSR03- C The Remote PSR03 is a simple control can control AV device through ZWave-to-IR extender, and it can also controls 8 lighting groups ON/OFF via basic set, based on Z-WaveTM technology. It is the Z-WaveTM plus product, it support the security, OTA... Those newest features of the Z-WaveTM technology.
PAGE 2
Adding to Z-WaveTM Network In the first time, activate the device through micro USB, then it can be added into the Z-WaveTM network. First, make sure the primary controller is in the add mode. And then power on the device. The device will auto start the NWI (Network Wide Inclusion) mode. And it should be added in 5 seconds. You will see the LED light ON one second. Function Add Remove Reset Description 1. Have Z-WaveTM Controller entered add mode. 2.
PAGE 3
switching and special function, the others are control keys. There are two group-buttons that can be switched by pressing central key. When the device is switched to group-button 1, LED will light on with red color for 3 seconds. When the device is switched to groupbutton 2, LED will light on with green color. PSR03-A has three keys on the device. The central one has panic function and the others can can control lock. PSR03-C has panic function.
PAGE 4
Top-left Key Top-right Key Bottom-left Key Bottom-right Key Lighting Lighting Lighting Lighting group group group group 1 2 3 4 (Association (Association (Association (Association group group group group 2) 3) 4) 5) group group group group 6) 7) 8) 9) Group-Button 2 Notification Type: Emergency Alarm (0x0A) Event: Contact Medical Service (0x03) * Timing Report: Notice: For switch AV control or lighting group control function please setting the configuration No.7 bit 0.
PAGE 5
* NWI When the device is activated, the device will check is it already adding to the network? If doesn't, it will auto start the NWI mode. The LED will flash in every second and continue 30 seconds. Until timeout or the device successful to add by controller. Users can hold down the central key, then press the top-right key three times within 1.5 seconds to abort the NWI mode. Over The Air (OTA) Firmware Update The device support the Z-Wave firmware update via OTA.
PAGE 6
NO. 2 Name Basic Set Level Def. 0xFF 0 7 Customer (*) Function Auto Report 10 Battery Time Association Group 2 82 Basic Set Level Vali d All All A B C   Description Setting the BASIC command value to turn on the light. The 0xFF(-1) means turn on the light. For dimmer equipment 1 to 100 means the light strength. 0 means turn off the light. Customer function switch, using bit control. 0 Bit0: Switch AV control/Lighting group control.
PAGE 7
association group 9. 0 means using the value of configuration 2 to set. Basic Set Level NO. Name Def. Vali d Description Range: Minimum 40 meters indoor, 100 meters outdoor line of sight. Operating Temperature: -10oC ~ 45oC For indoor use only. Specifications subject to change without notice due to continuing product improvement.
PAGE 8
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.