Installation Instructions

ManualsBrandsPhilio Technology ManualsElectronicsCO sensor

Z-Wave CO Sensor PSG04

Introduction

The Z-Wave CO Sensor PSG04 is designed to give early warning of

developing fires by giving off the alarm sounds from its build-in alarm

horn, based on Z-Wave

technology.

It is the Z-Wave

plus product, it support the security, OTA. Those

newest features of the Z-Wave

technology. Z-Wave

is a wireless

communication protocol designed for home automation, specifically to

remotely control applications in residential and light commercial

environments. The technology uses a low-power RF radio embedded or

retrofitted into home electronics devices and systems, such as lighting,

home access control, entertainment systems and household

appliances.

This product can be included and operated in any Z-Wave

network

with other Z-Wave

certified devices from other manufacturers and/or

other applications. All non-battery operated nodes within the network

will act as repeaters regardless of vendor to increase reliability of the

network.

The device adopt the Z-Wave

500 series chip, when your Z-Wave

network system is all made by Z-Wave

500 series devices. The

network system will have the advantages as below.

• Concurrent multi-channel support reduces external interference.

• Better RF range, improve about 10 meters in indoor.

• Support 100 Kbps transmit speed, speed up communication.

WARNING AND LIMITATION

！

WARNING!! This product is intended for use in ordinary indoor

locations of family living units. It is not designed to measure

compliance with Occupational Safety and Health Administration

(OSHA) commercial or industrial standards. It is designed to detect

carbon monoxide gas from any source of combustion, it is NOT

designed to detect CO, fire or any other gas.

Individuals with a medical problem may consider using warning

devices which provide audible and visual signals for carbon monoxide

concentrations under 30ppm.

This CO sensor is not suitable to install in a hazardous location, as

defined in the National Electrical Code.

This CO alarm will not work without power. Philio's PSG04 Carbon

Summary of content (11 pages)

PAGE 1
with other Z-WaveTM certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. Z-Wave CO Sensor PSG04 The device adopt the Z-WaveTM 500 series chip, when your Z-WaveTM network system is all made by Z-WaveTM 500 series devices. The network system will have the advantages as below. • • • Concurrent multi-channel support reduces external interference.
PAGE 2
Monoxide sensor will not work if the battery power is disconnected or cut off for any reason. Additionally, carbon monoxide must reach the CO alarm unit for the proper performance of CO gas detection. enter the exclusion mode. Node ID has been removed. 1. Product has a DSK string , you can key in first five digit to increment smart start process,or you can scan QR code. Carbon monoxide alarms may wear out because they contain electronic parts that fail at any time.
PAGE 3
Failed or success in add/remove the node ID can be viewed from Z-WaveTM Controller. Notice 1: Always RESET a Z-WaveTM device before trying to add it to a Z-WaveTM network • Notification Report (V4) Notification Type: CO (0x02) Event: CO detected, Unknown Location (0x02) CO Alarm Test (0x03) Sensor Binary Report (V2) Sensor Type: CO (0x03) Sensor Value: 0xFF Z-WaveTM Notification After the device adding to the network, it will wake-up once per day in default.
PAGE 4
3.Place the bracket so that the two longest hole slots are aligned on the line. In each of keyhole slots, draw a mark to locate a mounting plug and screw. this duration, the controller can communicate with the device. Normally the device is always sleeping to save the battery energy. Over The Air (OTA) Firmware Update 4.Remove the bracket. The device support the Z-Wave firmware update via OTA. Let the controller into the firmware update mode, and then press the 5.
PAGE 5
open the battery cover to expose the battery compartment. Three AA batteries have been included with your purchase. When replacing the batteries, we recommend use of following mentioned type of batteries: 3 pieces of AA 1.5V Energizer # E91 Alkaline battery; the battery life is at least one year under normal operation condition. or 3 pieces of AA 1.5V Energizer #L91 lithium battery; the battery life is at least one year under normal operation condition. or 3 pieces of AA 1.
PAGE 6
4 minutes, if the CO concentration caused the alarm still remains at alarming condition, the CO sensor will reactivate. Power on mode: Three LEDs blink and buzzer beeps for 0.5 second as soon as the batteries are installed. Stand-by mode: green LED flashes once in every 60 seconds, which means the unit is receiving power and also indicates it is functioning properly.
PAGE 7
reached. Tamper mode: The buzzer chirps once in a minute and the yellow LED is steadily on .until the CO alarm unit is mounted back to the bracket properly. (c) If no symptoms exist, immediately ventilate the home by opening windows and doors. Turn off fuel burning appliances and call a qualified technician or your utility company to inspect and repair your problem before restarting appliances.
PAGE 8
COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_CONFIGURATION COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_VERSION_V3 COMMAND_CLASS_SENSOR_BINARY_V2 COMMAND_CLASS_WAKE_UP_V2 COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_SECURITY COMMAND_CLASS_SECURITY_2 COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5 Figure 1: Location for placing CO alarm for A multi-floor CO alarms for minimum security Z-Wave Configuration Settings Do not place the CO alarm in the fo
PAGE 9
22~927MHz (Japan) 0: Using Notification Report. 1: Using Sensor Binary Report. 10 Auto Report Battery Time 0 Bit5: Reserve. 0 Bit6: Reserve. 0 Bit7: Reserve. 12 The interval time for auto report the battery level. 0 means turn off auto report battery. Each tick means 30 minutes. The default value is 12(6 hours). 0~127 920~924MHz (Taiwan; Korea) 865.20 MHz (IN), 869.00 MHz (RU), 921.40 MHz, 919.
PAGE 10
to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Alarm audibility: Over 85dB at 3m For indoor use only. Size: 12.5cm diameter x 3.5cm depth Specifications subject to change without notice due to continuing product improvement.
PAGE 11
When replacing old appliances with new once, the retailer is legally obligated to take back your old appliance for disposal at least for free of charge.