User's Manual

ManualsBrandsPhilio Technology ManualsElectronicsFlood Multi Sensor

Flood Multisensor PAT02-A/B/C

The flood multisensor PAT02 has flood, temperature and humidity, 3

sensors function in one, based on Z-Wave

technology.

It is the Z-Wave

plus product, it support the security, OTA... Those

newest features of the Z-Wave

technology. Z-Wave

is a wireless

communication protocol designed for home automation, specifically to

remotely control applications in residential and light commercial

environments. The technology uses a low-power RF radio embedded or

retrofitted into home electronics devices and systems, such as lighting,

home access control, entertainment systems and household appliances.

This product can be included and operated in any Z-Wave

network

with other Z-Wave

certified devices from other manufacturers and/or

other applications. All non-battery operated nodes within the network

will act as repeaters regardless of vendor to increase reliability of the

network.

The device adopt the Z-Wave

500 series chip, when your Z-Wave

network system is all made by Z-Wave

500 series devices. The

network system will have the advantages as below.

• Concurrent multi-channel support reduces external interference.

• Better RF range, improve about 10 meters in indoor.

• Support 100 Kbps transmit speed, speed up communication.

Function Compare A/B/C

Flood Temperature Humidity

PAT02-A V V V

PAT02-B V V

PAT02-C V

Add to/Remove from Z-Wave

Network

There are one tamper keys in the back side of the device, It can add,

remove, reset or association from the Z-Wave

network.

In the first time, add the device into the Z-Wave

network. First, make

sure the primary controller is in the add mode. And then power on the

device, just take out the insulation Mylar in the back side of the device.

The device will auto start the NWI (Network Wide Inclusion) mode. And

it should be included in 5 seconds. You will see the LED light ON one

second.

Notice: Including a node ID allocated by Z-Wave

Controller means

“Add” or “Inclusion”. Excluding a node ID allocated by Z-Wave

Controller means “Remove” or “Exclusion”.

Summary of content (9 pages)

PAGE 1
Flood Multisensor PAT02-A/B/C The device adopt the Z-WaveTM 500 series chip, when your Z-WaveTM network system is all made by Z-WaveTM 500 series devices. The network system will have the advantages as below. • • • Concurrent multi-channel support reduces external interference. Better RF range, improve about 10 meters in indoor. Support 100 Kbps transmit speed, speed up communication.
PAGE 2
Description 1. Have Z-WaveTM Controller entered inclusion mode. 2. Pressing the tamper key three times within 1.5 seconds to enter the inclusion mode. Add 3. After add successful, the device will wake to receive the setting command from Z-WaveTM Controller about 20 seconds. 1. Have Z-WaveTM Controller entered exclusion mode. 2. Pressing tamper key three times within 1.5 seconds Remove to enter the exclusion mode. Node ID has been excluded.
PAGE 3
Note: To disable send temperature report after the flood triggered, please setting the configuration N0.5 bit5 to 1. Sensor Binary Report (V2) Sensor Type: Water (0x06) Sensor Value: 0xFF *** Temperature differential report *** This function default is enabled, to disable this function by setting the configuration NO.21 to 0. In the default, when the temperature is changed to plus or minus one degree Fahrenheit (0.
PAGE 4
Low battery report: When the battery level is too low, every 30 minutes will report once. • Temperature report: Every 6 hours report once in default. It could be changed by setting the configuration NO. 13. • Humidity report: Every 6 hours report once in default. It could be changed by setting the configuration NO. 14. • Flood state report: Every 6 hours report once in default. It could be changed by setting the configuration NO. 15. Notice: The configuration NO.
PAGE 5
Battery Installation 2 When the device report the low battery message. The user should replace the battery to new one. The battery type is CR123A, 3.0V. The way to open the front cover please press the top position, to release the cover. 1 1 Replace the new battery and install the cover back. 1. Put the front cover bottom, and press down. 2. Push the front cover top. Installation 1. To mount the device on the wall, you can choose using the tape, or the screw. 2.
PAGE 6
NO. Name 1 Basic Set OFF Level 0 Basic Set ON Level 0xFF 2 Def. Valid A Setting the BASIC command value. All 33 32 Operation mode. Using bit to control. 0 Setting the temperature scale.    Bit3: 0: Fahrenheit, 1:Celsius 0    Bit4: Reserve. Bit5: Disable the temperature report after event triggered. (1:Disable, 0:Enable) 0  0    Bit6: Reserve.    Bit7: Reserve. 0 All 0 0 0 0 0 0 6 0    Bit0: Disable the Flood function.    Bit1: Reserve.    Bit2: Reserve.
PAGE 7
NO. Name Def. Valid A B C Description NO. Disable the humidity report after    Bit6: event triggered. (1:Disable, 0:Enable) 0 All 0     0 0 0 0 0 14   Bit0: Reserve.   Bit1: Reserve.   Bit2: Reserve.   Bit3: Disable send out BASIC OFF 0~ 127 15  0  0    Bit6: Disable to report battery state flood state. 0 means turn off auto report. The default value is 12. The tick time can setting by the configuration No.20.
PAGE 8
NO. Name 23 Humidity Differential Report Def. Valid A 5 0~ 60  Signal (Frequency): 868.40 MHz, 869.85 MHz(EU), 908.40 MHz, 916.00 MHz(US), 922~927 MHz(JP/TW), 921.40 MHz, 919.80 MHz(ANZ), 869.00 MHz(RU), 865.20 MHz(IN), 916.00 MHz(IL), Description B C The humidity differential to report. 0 means turn off this function. The unit is percentage. Enable this function the device will detect every 10 seconds. Range: Minimum 40 meters indoor, 100 meters outdoor line of sight.
PAGE 9
FCC Interference Statement Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.