User Manual

ManualsBrandsPhilio Technology ManualsElectronicsSmart energy plug in switch

PAN15-1/-2

Smart energy plug in switch

This plug-in ON/OFF switch PAN15 is a security enabled wireless switch, based on

Z-Wave Plus technology. Z-Wave Plus

enabled devices displaying the Z-Wave

Plus

logo can also be used with it regardless of the manufacturer, and can also be

used in other manufacturer’s Z-Wave

enabled networks. Remote On/Off control of

the connected load is possible with other manufacturer’s wireless Controller. Each

switch is designed to act as a repeater. Repeaters will re-transmit the RF signal to

ensure that the signal is received by its intended destination by routing the signal

around obstacles and radio dead spots. Because PAN15 supports Security

Command Class, it can learn with Secured controller. Its functionality and supported

command classes is identical when included as a secure and non-secure device.

This plug-in ON/OFF switch is able to detect instance wattage (1500W/UL/TW/JP)

and overload current (14.5A) of connected lights or appliances. When detecting

overload state, the Switch will be disabled and its On/Off button will be lockout of

which LED will flash quickly. However, unplug and re-connect the switch will reset its

overload condition to normal status.

Adding to Z-Wave

Network

In the front casing, there is an On/Off button with LED indicator which is used to

toggle switch on and off or carry out inclusion, exclusion, reset or association. When

first power is applied, its LED flashes on and off alternately and repeatedly at 0.5

second intervals. It implies that it has not been assigned a node ID and start auto

inclusion.

Auto Inclusion

The function of auto inclusion will be executed as long as the switch does not have

Node ID and just plug the switch into a wall outlet.

Note: Auto inclusion timeout is 2 minute during which the node information of

explorer frame will be emitted once several seconds. Unlike “inclusion” function as

shown in the table below, the execution of auto inclusion is free from pressing the

On/Off button on the Switch.

The table below lists an operation summary of basic Z-Wave functions. Please refer

to the instructions for your Z-Wave

Certificated Primary Controller to access the

Summary of content (11 pages)

PAGE 1
PAN15-1/-2 This plug-in ON/OFF switch is able to detect instance wattage (1500W/UL/TW/JP) and overload current (14.5A) of connected lights or appliances. When detecting Smart energy plug in switch overload state, the Switch will be disabled and its On/Off button will be lockout of P which LED will flash quickly. However, unplug and re-connect the switch will reset its overload condition to normal status.
PAGE 2
Setup function, and to include/exclude/associate devices 3. IDs are excluded. LED 0.5s On, 0.5s Off (Enter auto inclusion) Function Description Annotation No node ID The Z-Wave Controller does not allocate LED 2-second on, 2-second Z-Wave device, so associations a node ID to the Switch. off may be added or removed by a Inclusion 1. 1. PAN15 is an always listening Association controller at any time.
PAGE 3
No node ID 3. Press the button or switch on the load to the ON position. Under normal operation, when the Switch has not been allocated a node ID, the LED flashes on and off alternately at 2-second 4. To manually turn ON the Switch, press and release the On/Off button. The LED intervals. By pressing On/Off button, it will stop flashing temporarily. Learning will turn ON, and the load plugged into the Switch will also turn ON.
PAGE 4
ALARM_REPORT. Binary Switch Report Command: Report OFF:[Command Class Switch Binary, Switch Binary Report, Value =0(0x00)] 2-1 Auto report to Grouping 1 (Maximum Node 1) Report ON:[Command Class Switch Binary, Switch Binary Report, Value = 255(0xFF)] 2-1-1 On/Off Event Report When “on” or “off ” state has been changed, it will send Binary Switch Report to the 1-2 BASIC_SET / SWITCH_BINARY_SET node of Grouping 1.
PAGE 5
When PAN15 detects the current is more than 14.5A, it will send Alarm Report to Meter Type = 0x01 Group 1 node.
PAGE 6
Rate Type = 0x01 Meter Type = 0x01 2-2-4 AC load Voltage (V) Precision = 2 When receiving Meter Get Command, it will report Meter Report Command to the Scale = 0x00 (KWh) node.
PAGE 7
Meter Value 2 = 0x01(V) Size = 2 (2 Bytes of I) AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V) Meter Value 1 = 0x01(I) Meter Value 2 = 0x21(I) 2-2-5 AC load current ( I ) AC load current = (Meter Value 1*256) +(Meter Value 2)= 2.89 (A) When receiving Meter Get Command, it will report Meter Report Command to the node.
PAGE 8
Size = 1 (1 Byte of PF) 7 LED indication 1 1-2 1 1 : Show switch state 2 : Show night mode Meter Value 1 = 0x63(PF) mode Load power factor (PF) = Meter Value 1 =0.99 8 Auto off timer 2 0-0x7FFF 1s 0 0 : Disable auto off function 1-0x7FFF : 1s ~ 32767s 9 RF off com- 1 0-3 0 0 : Switch off 1 : Ignore mand mode 2 : Switch toggle 3 : Switch on 3.
PAGE 9
setting value is 10000, when the Accumulated Power Consumption of Relay1 over 3-9-3 Switch Toggle：It switches to the inverse of current state. this value, PAN15 will send KWH meter report to warn the Group1 node, 3-9-4 Switch On：It switches to ON state. minimum value is 1KWh and default value is 10000 kWh. 3-5 Restore switch state mode : 4.
PAGE 10
* COMMAND_CLASS_CONFIGURATION Specification * COMMAND_CLASS_ALARM * COMMAND_CLASS_PROTECTION * COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 Troubleshooting Operating Voltage 100~120Vac/ 60Hz; 220~240Vac/ 50Hz Maximum Load 13A Range Minimum 30 m in door 70m outdoor line of sight Operating Temperature 0°C ~ 40°C Frequency Range Symptom Cause of Failure Recommendation The Switch not working and 1. The Switch is not 1. Check power connections LED off 2.
PAGE 11
collection systems or contact the retailer where the product was to the following two conditions: purchased. They can take this product for environmental safe recycling. (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.