User Manual

ManualsBrandsPhilio Technology ManualsElectronicsIN Wall Watch

PAN06-1/-2/-3

In Wall Dual relay(1 way) switch module

Fig 1. Assembling

This in-wall switch module is a transceiver which is a Z-WaveTM enabled device and is fully compatible

with any Z-WaveTM enabled network. Mini size design let the module can easily hide itself into the wall

box and that will be good for the house decoration.

There are many kind of application by using the module to switch Load On and Off , one main application

is the light control. If connect the com port directly to AC Line terminal ,the new smart relay calibration

technology can reduce the inrush current caused by the load and let the module work perfectly with many

kind of light like incandescent, fluorescent and LED light. This module can also connect to alternative

power supply like DC 12V to switch on/off 12V MR-16 light as follow picture.

Adding to Z-Wave

Network

In the front casing, there is an on/off button with LED indicator below which is used to

toggle switch on and off or carries out inclusion, exclusion, reset or association.

When first power is applied, its LED flashes on and off alternately and repeatedly at

2-second intervals. It implies that it has not been assigned a node ID and cannot

work with Z-Wave enabled devices.

Auto Inclusion

The function of auto inclusion will be executed as long as the in wall switch does not

have Node ID and just connect the switch to main power.

Note: Auto inclusion timeout is 4 minute during which the node information of

explorer frame will be emitted once every 5 seconds. Unlike “inclusion” function as

shown in the table below, the execution of auto inclusion is free from pressing the

On/Off button on the Switch.

Summary of content (9 pages)

PAGE 1
PAN06-1/-2/-3 In Wall Dual relay(1 way) switch module technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of light like incandescent, fluorescent and LED light. This module can also connect to alternative power supply like DC 12V to switch on/off 12V MR-16 light as follow picture.
PAGE 2
The table below lists an operation summary of basic Z-Wave functions. Please refer Association 1. to the instructions for your Z-WaveTM Certificated Primary Controller to access the Have Z-Wave Controller entered One press one flash association mode. Setup function, and to include/exclude/associate devices Or Pressing Include button of PAN06 three times within 1.
PAGE 3
temporarily. However, after disconnect and reconnect the Switch, the LED will flash on and off alternately at 2-second intervals. Choosing a Suitable Location 1. Do not locate the Switch facing direct sunlight, humid or dusty place. 1. Put the in wall switch into a wall box and connect the AC power wire L,N to 2. The suitable ambient temperature for the Switch is 0°C~40°C. PAN06 connector L, N. 3. Do not locate the Switch where exists combustible substances or any source of 2.
PAGE 4
Report OFF when both relay 1 and relay 2 OFF Configuration parameter 1=2 switch ON and OFF of relay 1 Configuration parameter 1=2 Report ON when relay 1 ON Report OFF when relay 1 OFF Configuration parameter 1=3 switch ON and OFF of relay 2 Configuration parameter 1=3 Report ON when relay 2 ON Report OFF when relay 2 OFF , Basic Get Command: [Command Class Basic, Basic Get] [Command Class Basic, Basic Set, Value = (255)0xFF]: the load attached to Basic Report Command: the Switch turns on.
PAGE 5
2-1-1 On/Off Event Report COMMAND_CLASS_MULTI_CHANNEL When “on” or “off ” state has been changed (ex. Press S1 S2 or include on/off MULTI_CHANNEL_CMD_ENCAP button), it will send Binary Switch Report to the nodes of Group1~3.
PAGE 6
Command =0x03 (Switch_Binary_Report = 0x03) 3.
PAGE 7
Edge-Toggle mode: this mode is suitable for the normal bi-stable switch, every time Relay2 ON Basic Set or Binary_Switch_Set OFF Relay1 OFF when change the state of the wall switch will also swap the state of Relay1 or Relay2 & Relay2 OFF Get command Relay state Basic_Get or Binary_Switch_Get Relay1 ON 4.
PAGE 8
The Switch LED Check if the load connect Set the ON/OFF switch of the load illuminating, but cannot into the Switch has its control the ON/OFF own ON/OFF switch attached to ON Warning: 1.Plug out to disconnect from power supply; Do not plug in line. Switch of the load attached The Switch LED 2. Do not exceed the max rating 1. Not carry out illuminating, but the association Detector cannot control 1. Carry out association Disposal 2.
PAGE 9
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.