User Manual

ManualsBrandsPhilio Technology ManualsElectronicsIn Wall Single relay (1 way) switch

PAN05-1/-2/-3

In Wall Single relay(1 way) switch module

Fig 1. Assembling

This in-wall switch module is a transceiver which is a Z-WaveTM enabled device and

is fully compatible with any Z-WaveTM enabled network. Mini size design let the

module can easily hide itself into the wall box and that will be good for the house

decoration.

There are many kind of application by using the module to switch Load On and Off ,

one main application is the light control. If connect the com port directly to AC Line

terminal ,the new smart relay calibration technology can reduce the inrush current

caused by the load and let the module work perfectly with many kind of light like

incandescent, fluorescent and LED light. This module can also connect to alternative

power supply like DC 12V to switch on/off 12V MR-16 light as follow picture.

Adding to Z-Wave

Network

In the front casing, there is an on/off button with LED indicator below which is used to

toggle switch on and off or carries out inclusion, exclusion, reset or association. After

being excluded, its LED flashes on and off alternately and repeatedly at 2-second in-

tervals. It implies that it has not been assigned a node ID and cannot work with Z-

Wave enabled devices.

Auto Inclusion

The function of auto inclusion will be executed as long as the in wall switch does not

have Node ID and just connect the switch to main power.

Note: Auto inclusion timeout is 2 minute during which the node information of

explorer frame will be emitted once every 5 seconds. Unlike “inclusion” function as

Summary of content (8 pages)

PAGE 1
PAN05-1/-2/-3 In Wall Single relay(1 way) switch module There are many kind of application by using the module to switch Load On and Off , one main application is the light control. If connect the com port directly to AC Line terminal ,the new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of light like incandescent, fluorescent and LED light.
PAGE 2
shown in the table below, the execution of auto inclusion is free from pressing the seconds until LED is off. On/Off button on the Switch. Association The table below lists an operation summary of basic Z-Wave functions. Please refer 3. IDs are excluded. 1. Have Z-Wave Controller entered One press one flash association mode.
PAGE 3
off. No node ID Under normal operation, when the Switch has not been allocated a node ID, the LED flashes on and off alternately at 2-second intervals. By pressing S1 S2 or On/Off button, it will stop flashing temporarily. However, after disconnect and reconnect the Switch, the LED will flash on and off alternately at 2-second intervals. Learning When PAB01 is in learning mode, LED flashes on and off alternately and repeatedly at 0.5 second intervals. Choosing a Suitable Location 1.
PAGE 4
Wave system. load attached to the Switch turns off. 1-1 BASIC_GET / BINARY_SWITCH_GET 2. Z-Wave’s Groups (Association Command Class Version 1) Basic Get Command: [Command Class Basic, Basic Get] The Switch can be set to send reports to control associated Z-Wave devices. It Basic Report Command: supports only one association group and the group has one node support. Group1 Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)] support SWITCH_BINARY_REPORT, BASIC_REPORT.
PAGE 5
8 The content of Alarm Report Auto off 1 timer 9 Alarm report command:[Command Class Alarm, Alarm Report, Alarm Type RF Off 0- Second 0x7FFF 1 0-3 command = 0x08, Alarm Level = 0xFF] 0 mode 0 0：Disable auto off function 1-0x7FFF：1 ~ 32767seconds 0：Switch off 1：Ignore 2：Switch toggle 3：Switch on 3-1 Edge / Pulse / Edge-Toggle mode 3.
PAGE 6
3-4 LED indication Mode * COMMAND_CLASS_SWITCH_BINARY Show switch state：LED on for switch on and off for switch off. * COMMAND_CLASS_BASIC * COMMAND_CLASS_SWITCH_ALL Show switch state：LED off for switch on and on for switch off. * COMMAND_CLASS_CONFIGURATION The default value is Show switch state. * COMMAND_CLASS_ALARM 3-5 Auto Off timer * COMMAND_CLASS_SCENE_ACTIVATION * COMMAND_CLASS_SCENE_ACTUATOR_CONF When auto off timer is equal to 0, the auto off function will be disabled.
PAGE 7
the Switch Disposal interference Remove the load attached or check This marking indicates that this product should not be disposed with continuously, but cannot max. load cannot exceed other household wastes throughout the EU. To prevent possible harm to control 11A(230Vac/120Vac) the environment or human health from uncontrolled waste disposal, LED keep flashing Overload occurs recycle it responsibly to promote the sustainable reuse of material resources.
PAGE 8
encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules.