User Manual

ManualsBrandsPhilio Technology ManualsElectronicsIn Wall Switch

PAN04-1/-2/-3

In Wall Dual relay(1 way) switch module

Fig 1. Assembling

This in-wall dual relay switch module is a transceiver which is a Z-WaveTM enabled

device and is fully compatible with any Z-WaveTM enabled network. Mini size design

let the module can easily hide itself into the wall box and that will be good for the

house decoration.

There are many kind of application by using the module to switch AC power On and

Off , one main application is the light control. The new smart relay calibration

technology can reduce the inrush current caused by the load and let the module work

perfectly with many kind of light like incandescent, fluorescent and LED light.

This in-wall switch module is able to detect Instant power wattage (5~1500W) and

overload wattage (1600~1700W) of connected light or appliances. When detecting

overload state, the Module will be disabled and its On/Off button will be lockout of

which LED will flash quickly. However, disconnect and re-connect the Module will

reset its overload condition to normal status.

Adding to Z-Wave

Network

In the front casing, there is an on/off button with LED indicator below which is used to

toggle switch on and off or carry out inclusion, exclusion, reset or association. When

first power is applied, its LED flashes on and off alternately and repeatedly at 2-

second intervals. It implies that it has not been assigned a node ID and cannot work

with Z-Wave enabled devices.

Auto Inclusion

The function of auto inclusion will be executed as long as the in wall switch does not

have Node ID and just connect the switch to main power.

Note: Auto inclusion timeout is 4 minute during which the node information of

explorer frame will be emitted once every 5 seconds. Unlike “inclusion” function as

Summary of content (19 pages)

PAGE 1
PAN04-1/-2/-3 In Wall Dual relay(1 way) switch module Off , one main application is the light control. The new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of light like incandescent, fluorescent and LED light. This in-wall switch module is able to detect Instant power wattage (5~1500W) and P overload wattage (1600~1700W) of connected light or appliances.
PAGE 2
shown in the table below, the execution of auto inclusion is free from pressing the 2. On/Off button on the Switch. Within 1 second, press On/Off button again for 5 seconds until LED is off. 3. The table below lists an operation summary of basic Z-Wave functions. Please refer IDs are excluded. 1. Have Z-Wave Controller entered Association to the instructions for your Z-WaveTM Certificated Primary Controller to access the 2-second on, 2-second off One press one flash association mode.
PAGE 3
node ID, the LED flashes on and off alternately at 2-second intervals. By pressing S1 S2 or On/Off button, it will stop flashing temporarily. However, after disconnect and reconnect the Switch, the LED will flash on and off alternately at 2-second intervals. Overload When overload state occurs, the Switch is disabled of which LED flashes on and off alternately at 0.5 second intervals. Overload state can be cleared by disconnect and reconnect the Switch to the main power Choosing a Suitable Location 1.
PAGE 4
OFF. Report ON:[Command Class Basic, Basic Report, Value = (255)0xFF] Binary Switch Get Command:[Command Class Switch Binary, Switch Programming Binary Get] Binary Switch Report Command: 1. Basic Command Class / Binary Switch Command Class Report OFF:[Command Class Switch Binary, Switch Binary Report, Value The Switch will respond to BASIC and BINARY commands that are part of the Z- =0(0x00)] Wave system.
PAGE 5
to Z-Wave Controller. the Switch turns on. [Command Class Basic, Basic Set, Value = 0(0x00)]: the load attached to the Switch turns off. 2-1 Auto report to Grouping 1 ~3(Maximum Node 1) [Command Class Switch Binary, Switch Binary Set, Value = (255)0xFF]: the load attached to the Switch turns on. [Command Class Switch Binary, Switch Binary Set, Value = 0(0x00)]: the 2-1-1 On/Off Event Report load attached to the Switch turns off.
PAGE 6
Meter Get Command: [Command Class Meter, Meter Get, Scale =0x02(W)] Meter Report Command: [Command Class Meter，Meter Report，scale(bit 2) +Rate Type +Meter Type，Precision + Scale(bit 1,0)+ Size，Meter 2-1-3 overload alarm report command Value 1，Meter Value 2，Meter Value 3，Meter Value 4] When PAN04 detect the overload , it will send Alarm Report to the correspond Rate Type = 0x01 Group。 Meter Type = 0x01 The content of Alarm Report Precision = 1 Scale = 0x02(W) Size = 4 Bytes (Meter Value) Alarm repor
PAGE 7
the node asked. Meter Value 3 = 0x38(W) Meter Value 4 = 0xA3(W) Meter Get Command: [Command Class Meter, Meter Get, Scale = 0x00 Accumulated power consumption (KW/h) = (Meter Value 2*65536) + (Meter Value KW/h)] 3*256) + (Meter Value 4) = 800.
PAGE 8
Precision = 1 Scale = 0x04(V) Rate Type = 0x01 Size = 2 Bytes (Meter Value) Meter Type = 0x01 Meter Value 1 = High Byte (V) Precision = 2 Meter Value 2 = Low Byte (V) Scale = 0x05(I) Size = 2 Bytes (Meter Value) Example: Meter Value 1 = High Byte (I) Scale = 0x04 (V) Meter Value 2 = Low Byte (I) Precision = 1 Size = 2 (2 Bytes of V) Example: Meter Value 1 = 0x09(V) Scale = 0x05 (I) Meter Value 2 = 0x01(V) Precision = 2 AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.
PAGE 9
when both Relay 1 and Relay2 OFF . If endpoint set to 2 , PAN04 will reply state of Relay1 .
PAGE 10
reply ON(0xFF) either Relay 1 or Relay2 this value will be 0) is ON, report OFF (0x00) when both (Bit Address+Destination End Point = 0x02) (Bit Address =0；Destination End Point Relay 1 and Relay2 OFF range1~3) (Bit Address+Destination End Point = 0x05) (Bit Address =0；Destination End Point) Command Class = 0x25 (Command_Class_Switch_Binary = 0x25) Command Class = 0x25 (Command_Class_Switch_Binary = Command =0x01 0x25) Command =0x03 Parameter 1 = 0xFF (Switch_Binary_Set = 0x01) (Switch_Binary_
PAGE 11
range1~3) Command Class = 0x32 Source End Point = 0x03 (this is the endpoint of command owner, here we assume endpoint is 3，if the ( Command_Class_Meter_V3 = 0x32) owner doesn’t support multi Channel Command =0x03 (Meter_Supported_Get = 0x03) this value will be 0) (Bit Address+Destination End Point = 0x01) (Bit Address =0；Destination End Point range1~3) Below is the example show PAN04 report to last command COMMAND_CLASS_MULTI_CHANNEL Command Class = 0x32 MULTI_CHANNEL_CMD_ENCAP Command =0x05 Sou
PAGE 12
Command =0x01 Parameter 1 = 0x00 (Meter_Get = 0x01) Parameter 6 = 0xFD (Scale = KWH = 0x00) 2-3-5-2 Get Instant Power Consumption (Watt) from endpoint METER_GET example： Accumulated power consumption (KWH) Report example： COMMAND_CLASS_MULTI_CHANNEL COMMAND_CLASS_MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP MULTI_CHANNEL_CMD_ENCAP Source End Point = 0x05 Source End Point = 0x03 here we assume endpoint is 5，if the (Meter report = Endpoint3) owner doesn’t support multi Channel this (Bit Address+Destin
PAGE 13
(Bit Address+Destination End Point = 0x05) (Bit Address =0；Destination End Point value will be 0) = command owner Endpoint value) Command Class = 0x32 (Bit Address+Destination End Point = 0x03) (Command_Class_Meter_V3 = 0x32) Command =0x02 (Bit Address =0；Destination End Point range1~3) (Meter_Report = 0x02) Parameter 1 = 0x21 Command Class = 0x32 (Scale Bit2 = 0 ，Rate Type = 0x01， Meter Type=0x01) Parameter 2 = 0x34 (Precision = 1，Scale Bit1Bit0 = ( Command_Class_Meter_V3 = 0x32) Command =0x0
PAGE 14
Parameter 3 = 0x09 Voltage = 0x0910 = 232.
PAGE 15
(Bit Address+Destination End Point = 0x03) Command Class = 0x32 (Bit Address =0；Destination End Point Parameter 3 = 0x63 range1~3) 3.
PAGE 16
3-3 Selected Endpoint mode 5 Threshold 2 10-1500 1watt If Controller not using Multi_Channel command class to access the endpoint of 1500 of Watt PAN04, you may configure the endpoint value to react the Basic Command Class for Load 、Binary Switch Command Class or Meter Command Class V3 Caution 3-3-1 Selected Endpoint 1： Default Selected Endpoint is 1 6 Threshold 2 1-10000 1KWh 10000 of KWH Set command Relay state for Load Basic Set or Binary_Switch_Set ON Relay1 Caution ON & Relay
PAGE 17
Meter_Get Current Relay1 I1+Relay2 I2 Meter_Get Power factor PF Relay1 3-6 Threshold of KWh for Load Caution This is a warning when the KWh of load over the preset threshold value, If the setting value is 10000, when the Accumulated Power Consumption of Relay1 or 3-3-2 Selected Endpoint 2 Relay2 over this value, PAN04 will send KWh Meter Report command to the node of Similar like Selected Endpoint 1 but only relate to Relay1 and ignore Relay2 correspond Guoup, minum value is 1KWh and default value
PAGE 18
Troubleshooting Maximum Load 1500W X2 (220V) 800W X 2 (120V) Recommendation Range Minimum 30 m in door 100m outdoor line of sight The Switch not working and 1. The Switch is not 1. Check power connections Operating Temperature 0°C ~ 40°C LED off 2. Don’t open up the Switch and Frequency Range Symptom Cause of Failure connect to the Main power send it for repair. PAN04-1 868.42 (EU) / PAN04-2 908.42(USA/Canada) / PAN04-3 922.5/923.9/926.3MHz (Taiwan/JP)MHz 2.
PAGE 19
Taipei City 24257,Taiwan(R.O.C) This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.