User's Manual

ManualsBrandsPhilio Technology ManualsElectronicsIn Wall Smart Dimmer

PAD07 In Wall Smart Dimmer

Warning: Do not use Non-Dimmable LED lamps.

Fig 1. Assembling & Wiring

Built-in High Breaking Capacity current fuse protection. Rating : 2A /250V.

Built-in Thermal Cutoff Fuses protection. Rated Temperature :125 °C; Rating :

2A /250V.

PAD07 is a security enabled wireless dimmer, based on Z-Wave Plus technology. Z-

Wave Plus

enabled devices displaying the Z-Wave Plus

logo can also be used

with it regardless of the manufacturer, and can also be used in other manufacturer’s

Z-Wave

enabled networks. You can On/Off the light by pressing the button briefly,

or a long pressing to control the brightness of dimmable light bulb.

This dimmer is a transceiver which is a security enabled device which based on

Z-Wave Plus technology, and it is fully compatible with any Z-Wave

enabled

network. Since PAD07 supports Security Command Class, it can learn with

Secured controller. Its functionality and supported command classes is identical

when included as a secure and non-secure device.

Adding to Z-Wave

Network

In the front casing, there is an on/off button (also an include button) with LED indica-

tor below which is used to dim on and off or carries out inclusion, exclusion, reset or

association. When first power applied, its LED flashes on and off alternately and re-

peatedly at 0.5 second intervals. It implies that it has not been assigned a node ID

and start auto inclusion.

Auto Inclusion

The function of auto inclusion will be executed as long as the dimmer does not

have Node ID and just connect the switch to main power.

Note: Auto inclusion timeout is 2 minute during which the node information of

explorer frame will be emitted once every several seconds. Unlike “inclusion” function

as shown in the table below, the execution of auto inclusion is free from pressing the

Summary of content (8 pages)

PAGE 1
Built-in High Breaking Capacity current fuse protection. Rating : 2A /250V. PAD07 In Wall Smart Dimmer Built-in Thermal Cutoff Fuses protection. Rated Temperature :125 °C; Rating : 2A /250V. PAD07 is a security enabled wireless dimmer, based on Z-Wave Plus technology. ZWave PlusTM enabled devices displaying the Z-Wave PlusTM logo can also be used with it regardless of the manufacturer, and can also be used in other manufacturer’s Z-WaveTM enabled networks.
PAGE 2
On/Off button on the dimmer. Reset 1. Pressing Include button of PAD07 Use this procedure only in The table below lists an operation summary of basic Z-Wave functions. Please refer three times within 2 seconds will the event that the primary to the instructions for your Z-WaveTM Certificated Primary Controller to access the enter inclusion mode. controller is lost or Setup function, and to Add/Remove/associate devices 2. Within 1 second, press Include button otherwise inoperable.
PAGE 3
To distinguish what mode the switch is in, view from the LED for identification. S1/S2 shortly when the light is on. To adjust the dim level, press and hold the On/Off button or S1/S2 until the desired dim level is achieved, then release. State Type LED Indication Normal Whenever we switch On and off of the PAD07 by On/Off button or RF No node ID Learning command, the LED will lights up when switch on; whereas LED off Programming when switch off. 1.
PAGE 4
Switch Report 1-2 BASIC_SET / MULTILEVEL_SWITCH _SET Multilevel Upon receipt of the following commands from a Z-Wave Controller, the load ON:[Command Class Multilevel Switch, Multilevel Switch Report, Value attached to the dimmer will turn on or off. =1~99] OFF:[Command Class Multilevel Switch, Multilevel Switch Report, Value [Command Class Basic, Basic Set, Value = 0] : the load attached to the =0(0x00)] dimmer turns off.
PAGE 5
3 External switch 1 1-3 1 could be Dimmer off、Last dimmer state、Dimmer on. The default setting is Last dim- 1 : One switch mode 2 : Two switch mode type mer state. 3: Up/Down switch mode 4 Restore dimmer 1 0-2 1 0 : Dimmer off 4. Firmware update over the air (OTA) 1 : Last dimmer state state PAD07 is based on 500 series SoC and supports Firmware Update Command 2 : Dimmer on Class, it can receives the updated firmware image sent by controller via the Zwave RF media.
PAGE 6
Specification Troubleshooting Input Rating:(Operating Voltage) 100~240Vac / 50Hz~60Hz 0.01~1A ; (Maximum: 1A) Symptom Cause of Failure Recommendation Input Rating:(Operating Current) The dimmer does not 1.The dimmer does not 1. Check power connections Output Rating: Maximum Load (Current) Maximum: 0.9A (100~240Vac) 2.
PAGE 7
Disposal Warning: Do not use Non-Dimmable LED lamps. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material DANGER Danger of electrocution! resources.
PAGE 8
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.