User Manual 300Mbps Wireless N NAS Router FWR-714U User Manual / V1.
Copyright Statement PHICOMM is the registered trademark of Shanghai Feixun Communication Co., Ltd. Other trademark or trade name mentioned herein are the trademark or registered trademark of the company. Copyright of the whole product as integration, including its accessories and software, belongs to Shanghai Feixun Communication Co., Ltd. Without the permission of Shanghai Feixun Communication Co., Ltd., individual or party is not allowed to copy, plagiarize, imitate or translate it into other languages.
00Mbps Wireless N NAS Rout www.phicomm.com CONTENTS Chapter 1: Introduction ......................................... 1 Product Overview .......................................................................................1 Main Features ..............................................................................................5 Chapter 2: Installation ................................................ 6 Physical Connection...............................................................................
www.phicomm.com 300Mbps Wireless N NAS Rout WPS Settings .................................................................................................................. 30 WDS Settings.................................................................................................................. 31 DHCP Server .............................................................................................. 33 DHCP..........................................................................................
www.phicomm.com 300Mbps Wireless N NAS Rout Routing Settings ...................................................................................... 48 Static Routing Table .................................................................................................... 48 Dynamic Routing Settings ........................................................................................ 49 IP Bandwidth Control ............................................................................. 49 Storage ......
www.phicomm.com 300Mbps Wireless N NAS Rout Firmware Upgrade........................................................................................................ 63 Reboot............................................................................................................................... 64 Logout.......................................................................................................... 64 Chapter 4: Download Wizard ...................................... 65 Before you start ..
300Mbps Wireless N NAS Rout www.phicomm.com Chapter 1: Introduction Product Overview Thank you for choosing FWR-714U Wireless N Router. FWR-714U 300Mbps Wireless N Router is an all-in-one router, ideal for home and SOHO users to share broadband Internet connection over the wired and wireless network. With the speed of up to 300Mbps, it can provide users with extraordinary smooth internet surfing, internet phone calling and on-line gaming.
www.phicomm.com 300Mbps Wireless N NAS Rout Power LED: The Power LED lights up when the Router is powered on. When the Router goes through its self-diagnostic mode during every boot-up, the LED flashes. When the diagnostic is complete, the LED is continuously lit. WLAN LED: The Wireless LED lights up when the wireless feature is enabled. It flashes when the Router sends or receives data over the wireless network.
300Mbps Wireless N NAS Rout www.phicomm.com Internet LED: The Internet LED lights up when there is a connection made through the Internet port. It flashes to indicate network activity over the Internet port. LED (1~4): These LEDs are corresponding with the LAN ports on the rear panel. The LED is continuously lit when the Router is connected to a device through that port. It flashes to indicate network activity over that port.
www.phicomm.com 300Mbps Wireless N NAS Rout Rear Panel ON/OFF: The power on/off button. PWR: The Power port connects to the included power adapter. LAN (1-4): Using Ethernet cables, these Ethernet ports (4, 3, 2, 1) connect the Router to computers and other Ethernet network devices on your wired network.
www.phicomm.com 300Mbps Wireless N NAS Rout USB: Plug a storage device or a USB printer into this port. WPS: Press the button and the WPS LED in front panel flashing, WPS function is enabled. RST: Long press and hold the button for 8 seconds, the Router will restore to its factory default settings.
300Mbps Wireless N NAS Rout www.phicomm.com Chapter 2: Installation Physical Connection Note: • Actual product may be different as the picture, but the installation will be the same. • Please use the included power adapter. Use of a different power adapter could cause damage and void the warranty for this product. • Please ensure the Power, WLAN, LAN and Internet lights are ON when the installation finished successfully.
www.phicomm.com 300Mbps Wireless N NAS Rout Configure the Computer’s IP Address After connecting your PC to the router, please configure your PC’s IP address. For Windows XP/2000 1) Click Start > Control Panel. 2) Select and double click Network Connections.
www.phicomm.com 300Mbps Wireless N NAS Rout 3) Right click Local Area Connection and then select Properties. 4) Select Internet Protocol (TCP/IP) and click Properties.
www.phicomm.
www.phicomm.com 300Mbps Wireless N NAS Rout 5) Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. For Windows Vista/7 1) Click Start>Control Panel.
www.phicomm.com 300Mbps Wireless N NAS Rout 2) Click Network and Internet. 3) Click Network and Sharing Center.
www.phicomm.com 300Mbps Wireless N NAS Rout 4) Go to Change Adapter Settings (win7)/Manage Network Connections (Vista). 5) Right click Local Area Connection, choose Properties.
www.phicomm.com 300Mbps Wireless N NAS Rout 6) Select Internet Protocol Version 4 (TCP/IPv4) and click Properties. 7) Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK.
www.phicomm.com 300Mbps Wireless N NAS Rout Setup Wizard After successful installation, you can go ahead with connecting to the internet, the operations are as follow: 1) Open your web browser, in the address bar, type in 192.168.0.1 2) You are prompt to enter the Username/Password (preset as admin/admin) which you can found on the label at the bottom of your router, and then click Login.
www.phicomm.com 300Mbps Wireless N NAS Rout 4) Please choose your WAN connection type, there are five options available: Static IP, DHCP, PPPoE, L2TP and PPTP. a. Select Static IP if your ISP gives you the Static IP Address, Subnet Mask, Default Gateway and DNS Server Address, type in those information and then click Next. b. Select DHCP if your ISP does not gives you any IP numbers to use. This option is commonly used for cable modem services. Router will obtain IP address information automatically.
www.phicomm.
www.phicomm.com 300Mbps Wireless N NAS Rout c. PPPoE is typically used for DSL services. Select PPPoE and type in the Username and Password provided by your ISP, and then click Next. d. Select L2TP if your ISP provides L2TP connection, and then click Next. e. Select PPTP if your ISP provides PPTP connection, and then click Next.
www.phicomm.com 300Mbps Wireless N NAS Rout 5) In this page, the SSID is the name of your wireless network, you can give it a different name. For the Wireless Mode, you can leave it as 11 b/g/n mixed mode, as for the Wireless Security, we recommend you to choose WPA-Personal/WPA2-Personal, and then set up a password, click Next. 6) Click Finish, then you can check the internet is working or not.
www.phicomm.com 300Mbps Wireless N NAS Rout Chapter 3: Router Configuration You can see there are thirteen main menus on the left side of the router’s web management page. On the right side, you can see a small HELP button, there are the corresponding explanations and instructions. The Running Status page shows the current status of the Router. Network Settings The Network Settings section helps you to configure the Router to access the Internet.
www.phicomm.
300Mbps Wireless N NAS Rout www.phicomm.com WAN WAN Connection Type: To make sure the connection type your ISP provides, please refer to the ISP for more information. Dynamic IP (DHCP): Connections use dynamic IP address assignment, it means your ISP is running a DHCP server. Static IP: Connections use static IP address assignment, it means your ISP provides a static or fixed IP Address, Subnet Mask, Gateway and DNS setting. PPPoE: Connections requires username and password.
www.phicomm.com 300Mbps Wireless N NAS Rout DNS IP addresses. Otherwise, leave it unchecked, the DNS servers will be assigned from ISP dynamically. Primary DNS Server: Enter the DNS IP address in dotted-decimal notation provided by your ISP. Secondary DNS Server: Enter another DNS IP address in dotted-decimal notation provided by your ISP. Note: If you get Address not found error when you access a website, it is likely that your DNS servers are set up improperly.
300Mbps Wireless N NAS Rout www.phicomm.com MAC Address Clone Some ISPs require you to register the MAC Address of your computer. Choose Enabled, and then click Clone My PC’s MAC Address, then click Save. Dynamic DNS Dynamic DNS lets you assign a fixed host and domain name to a dynamic Internet IP address. If you want to use this feature, please register for this service with DDNS service providers such as www.no-ip.com first.
0Mbps Wireless N NAS Rout www.phicomm.com Wireless Basic Settings Wireless Status: Choose Enable to enable the wireless function of the router, choose Disable to disable the wireless function of the router. SSID: Enter a value of up to 32 characters. This is the name of your wireless network, you can give it a different name which can be easier for you to remember. Wireless Mode: If all of the wireless devices connected with this wireless router are in the same transmission mode (eg. 802.
300Mbps Wireless N NAS Rout www.phicomm.com change the wireless channel if you notice interference problems with another nearby access point, or the wireless performance is not as good as you expected. SSID Broadcast: If you choose Enabled, the wireless router will broadcast its name (SSID) . BSSID: The physical address of the router. Channel Bandwidth: The bandwidth of the wireless channel, you can select 20MHz or 20/40MHz.
300Mbps Wireless N NAS Rout www.phicomm.com Mode 2: Security Mode > Open/Shared/ WEPAUTO Open System: Select 802.11 Open System authentications. Shared Key: Select 802.11 Shared Key authentications. WEPAUTO: Select Shared Key or Open System authentication type automatically based on the wireless station's capability and request. You can select ASCII or Hex format. ASCII Format stands for any combination of keyboard characters in the specified length.
300Mbps Wireless N NAS Rout www.phicomm.com You can select one of following versions: WPA-Personal: Pre-shared key of WPA. WPA2-Personal: Pre-shared key of WPA2. WPA- Personal/ WPA2-Personal: Select WPA-Personal or WPA2-Personal automatically based on the wireless station's capability and request. Encryption: You can select TKIP, AES or TKIP+AES. Password: The password should be between 8 and 63 characters.
300Mbps Wireless N NAS Rout www.phicomm.com If you only want MAC address (00:0A:EB:00:07:5F) to access the Wireless Network while others cannot: 1. Click Add button. 2. Choose Allow for the security policy. 3. Fill MAC address 00:0A:EB:00:07:5F in and click Save. If you want MAC address (00:0A:EB:00:07:5F) cannot access the Wireless Network while others can: 1. Click Add button. 2. Choose Reject for the security policy. 3. Filling MAC address 00:0A:EB:00:07:5F in and click Save.
300Mbps Wireless N NAS Rout www.phicomm.com default values, otherwise it may result in lower wireless network performance. BG protection Mode: Auto by default. You can select On or Off. Beacon Interval: The interval for sending packets of the Beacon frame. Its value range is 20-1000 in unit of ms. The default is 100. DTIM Interval: It indicates the interval of the delivery traffic indication message (DTIM). The value range is between 1 and 255 milliseconds. The default value is 1.
www.phicomm.com 300Mbps Wireless N NAS Rout Wireless Clients List Click Refresh button to check the wireless clients. WPS Settings The WPS function can help you add a new device to the network quickly.
www.phicomm.com 300Mbps Wireless N NAS Rout within two minutes. The status LED on the router will light green for five minutes if the device has been successfully added to the network; If your client asks for the Router’s PIN number, enter the router’s PIN number into your client device; If your client device has a WIFI Protected Setup PIN number, enter that number in the PIN box.
300Mbps Wireless N NAS Rout www.phicomm.com The WDS function can help you extend the wireless range, it supports Bridge Mode and Repeater Mode. Bridge Mode: You can wirelessly connect two or more wired networks via this mode. In this mode, you need to add the wireless MAC address of the connecting device into the Routers AP MAC address table or select one from the scanning table. At the same time, the connecting device should be in Lazy, Repeater or Bridge mode.
www.phicomm.com 300Mbps Wireless N NAS Rout should be in Lazy, Repeater or client mode. Security Mode: You can select WEP 64bits mode, WEP 128bits mode, WPA-PSK (TKIP) mode, WPA2-PSK (AES) mode. Password: Enter the password, the format is decided by the encryption method you selected. Wireless Access Node MAC Address: Input the MAC address of the other wireless router. Note: Two wireless routers must use the same channel, encryption type and encryption key.
300Mbps Wireless N NAS Rout www.phicomm.com DHCP Server: If you disable the server, please make sure you have another DHCP server in your network. Start IP Address: The first address in the IP Address pool. End IP Address: The last address in the IP Address pool. Lease Time: It is the time interval that server will change to use another DHCP address. Default Gateway: (Optional) Suggest to input the IP Address of the LAN port of the Router.
300Mbps Wireless N NAS Rout www.phicomm.com Address Reservation When you specify a reserved IP address for a PC in the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses could be assigned to servers that require permanent IP settings. IP Address: The IP address that the Router reserved. MAC Address: The MAC Address of the PC that you want to reserve for an IP address.
www.phicomm.com 300Mbps Wireless N NAS Rout NAT There are five submenus under the NAT menu: Port Forwarding, Port Triggering, DMZ Host, UPnP and Multicast Forwarding. Click any of them, and you will be able to configure the corresponding function. Port Forwarding Choose Enabled, then click Add button.
www.phicomm.com 300Mbps Wireless N NAS Rout Rule’s Name: You can give this rule a name. Server IP Address: The IP address of the server you want to open the port, it is like 192.168.0.X. Server Port Range: The port range of the server you want to open the port. Client Port Range: The port range of the client. Protocol: The protocol of the server. Note: Please assign a static IP address to the server. Port Triggering Click Add button.
www.phicomm.com 300Mbps Wireless N NAS Rout Application Name: Describe the name of the application that being set. Please select one of the applications: There are few common applications available such as Dailpad, MSN gaming, PC Phone etc. the blank will be automatically filled once been chosen. Customize Application Name: If the application you want to add is not included, enter the blank manually. Start/End Trigger Port: The port for outgoing traffic.
300Mbps Wireless N NAS Rout www.phicomm.com Open Port: The port or port range used by the remote system when it responds to the outgoing request. A response using one of these ports will be forwarded to the PC that triggered this rule. Open Port Protocol: The protocol used for Incoming Ports Range, it can be TCP, UDP or TCP/UDP. If you are not clear about which protocol was being used, TCP/UDP is recommended.
www.phicomm.com 300Mbps Wireless N NAS Rout Choose Enable Special DMZ. MAC Address of the Special DMZ Host: Enter the MAC Address of the computer in the LAN that you want to set to a DMZ host. If you check Setting the Current PC’s MAC Address, the current PC’s MAC address will come up automatically. Note: • Before using DMZ Host, you should assign a static IP address to the designated server, and then enter this static IP address into router as the Server IP Address.
300Mbps Wireless N NAS Rout www.phicomm.com UPnP UPnP: Click the checkbox to Enable or Disable the UPnP. Save: Click Save button to save your setting. Multicast Forwarding Settings Multicast Forwarding enables the router to issue IGMP host message on behalf of hosts that the router discovered through standard IGMP interfaces. Group Mac: The Mac Address of the Multicast Forwarding Group. Group IP: The IP Address of the Multicast Forwarding Group. Host IP: The IP Address of the Group members.
www.phicomm.com 300Mbps Wireless N NAS Rout Security Options There are four submenus under the Security Options menu: Security Settings, Advanced Security Settings, Local Web Management and Remote Web Management. Click any of them, and you will be able to configure the corresponding function. Security Settings SPI (Stateful Packet Inspection): When the SPI firewall is enabled, the system refuses all requests from the Internet.
300Mbps Wireless N NAS Rout www.phicomm.com network through the router by using the VPN protocol, such as PPTP, L2TP, or IPSec, you need to enable the corresponding VPN pass through. ALG (Application Layer Gateway): ALG supports that some protocols at the application layer that adopt the control/data mode, such as FTP, TFTP, and H323, help to translate network addresses and ports at the NAT gateway. You are recommended to enable this option.
www.phicomm.com 300Mbps Wireless N NAS Rout TCP-SYN-FLOOD attacks. TCP-SYN-Attack Packet Threshold: If the number of TCP-SYN data packets exceeds the threshold, the defense measures act immediately. Block the PING packets from the WAN interface: If you select this option, the PC in the WAN cannot send the PING packets to the router. Block the PING packets from the LAN: If you select this option, the PC in the LAN cannot send the PING packets to the WAN.
www.phicomm.com 300Mbps Wireless N NAS Rout Remote Web Management This section is to allow the network administrator to manage the Router remotely. If you want to access the Router from outside the local network, please select the Enable Remote Web Management. Web Management Port: The management port open to outside access the default value is 80. Allowed Remote IP Address: Specify the range of the WAN IP address for remote management.
www.phicomm.com 300Mbps Wireless N NAS Rout MAC/IP/Port Filter This page is used to enable the firewall filtering function, select the filtering service or manually set the parameters that need to be filtered, such as MAC address, IP address and Port. You must set at least one filtering condition. You may also set multiple conditions or all the conditions. MAC/IP/Port Filter: Select Enabled or Disabled to enable or disable filtering.
www.phicomm.com 300Mbps Wireless N NAS Rout Note: Please synchronize the router’s time first when selecting the timing function.
www.phicomm.com 300Mbps Wireless N NAS Rout Web URL Filter URL: Put in the URL you want to filter. Routing Settings There are two submenus under the Routing Settings menu: Static Routing Table and Dynamic Routing Settings. Click any of them, and you will be able to configure the corresponding function. Static Routing Table Static routes give the router information that it cannot learn automatically through other means Use the Static Routing page to add or delete a route. The max number is 10.
www.phicomm.com 300Mbps Wireless N NAS Rout Destination: This is the IP address of the network or host that you want to assign to a static route. Subnet Mask: The Subnet Mask determines which portion of an IP address is the network portion, and which portion is the host portion. Gateway: This is the IP address of the default gateway device that allows for the contact between the Router and the network or host.
300Mbps Wireless N NAS Rout www.phicomm.com Enable IP bandwidth control: If you select it, the bandwidth control rule takes effect. Total Uplink Bandwidth: The rate of uploading through the WAN interface. Total Downlink Bandwidth: The rate of downloading through the WAN interface. Note: • The bandwidth conversion: 1 Mbps = 1024 Kbps. • Select the type of the broadband line and the bandwidth according to the actual situation. If you are not sure about the information, consult your broadband provider.
www.phicomm.com 300Mbps Wireless N NAS Rout UserAdmin The user in LAN can share the folder on mass-storage device which is plugged at USB connector. Click Add button, you can create a new user account, allow or prohibit the user to use FTP or SAMBA server.
www.phicomm.com 300Mbps Wireless N NAS Rout Disk Management Click Add button, you can manage the Folder and the Partition of disk. FTP Server You can create a FTP Server that can be accessed from internet or local network in this page. This function is disabled by default.
300Mbps Wireless N NAS Rout www.phicomm.com FTP Server: Choose Enabled or Disabled to enable or disable this function. FTP Server Name: You can give this FTP Server a name. Anonymous Login: Choose Enabled or Disabled to allow or deny Anonymous Login. FTP Port: The default port number is 21, please don’t change unless necessary. Max Sessions: The default number is 10, please don’t change unless necessary. Read File: Choose Enabled, the file can be read, choose Disabled, the file cannot be read.
www.phicomm.com 300Mbps Wireless N NAS Rout PRINTER Server To Enable Printer Function, follow these steps: 1. Please ensure that USB Media has plug in. 2. Choose Enabled. 3. Click Save to save the change. MINIDLNA Server To Enable MINIDLNA Function, follow these steps: 1. Please ensure that USB Media has plug in. 2. Highlight Enabled and set the MINIDLNA Port. 3. Click Save to save the change.
www.phicomm.com 300Mbps Wireless N NAS Rout 4. Enter the name of the path you want to share; you can select the type you want to share. 5. Click Add to complete the Directories settings. DOWNLOAD Choose Enable, then run Download Wizard, you can keep downloading even PC is turned off. If you want to know more about the offline download configuration, please refer to chapter 4.
300Mbps Wireless N NAS Rout www.phicomm.com System Tools There are ten submenus under the System Tools: Network Time settings, Diagnostics, WOL, Factory Defaults, Backup and Restore, Password, System Log, Traffic Statistics, Firmware Upgrade and Reboot. Click any of them, and you will be able to configure the corresponding function. Network Time Settings Current time: Show the current time. Time Zone: Select your time zone from the drop-down menu. Network Time server: To set NTP server.
www.phicomm.com 300Mbps Wireless N NAS Rout Note: The system will Synchronous with the Network Time Server every hour after saving, and it will affect the WAN dial-up on demand.
300Mbps Wireless N NAS Rout www.phicomm.com Diagnostics Select: Select Ping or Tracert. IP Address/Domain Name: The destination IP address or domain name. Ping Packet Total: The number of transmitted data packet when Ping operation is carried out. Ping Packet Size: The size of transmitted data packet when Ping operation is carried out. Ping Timeout: The timeout time of the ping operation. Tracert Hops: The hops of tracert.
300Mbps Wireless N NAS Rout www.phicomm.com Below is a Ping diagnosis example that router has failed to connect to IP 100.1.1.1: Wake On LAN WOL broadcasts so called Magic Packet Frames across a network to wake up hardware that understands such packets. These are normally NICs with Wake On LAN function. MAC Address: Add a MAC address to wake the computer on. Explain PC: Description about the computer. Add: Click Add button to finish, and the computer will display in the list.
www.phicomm.com 300Mbps Wireless N NAS Rout Select one or more computers in the list, and click Apply button, these computers will be waked up. Factory Defaults Click Restore All Settings button to reset all configuration settings to their default values. Note: All changed settings will be lost when defaults are restored.
300Mbps Wireless N NAS Rout www.phicomm.com Backup and Restore In the Export Settings column, click Backup button to save all configuration settings to your local computer as a file. To restore the Router's configuration, follow these instructions: 1) Click Browse to find the configuration file which you want to restore. 2) Click Save to update the configuration with the file whose path is the one you have input or selected in the blank. Note: Keep the power on during the process, in case of any damage.
www.phicomm.com 300Mbps Wireless N NAS Rout System Log The system log is a detailed record of the websites that users on your network have accessed or attempted to access. You can enable remote System Log function to view the log in remote place. Enable remote System Log: Check the radio button to enable remote System Log. Save: Click Save to save your Log. Clean: Click Clean to clear all shown information.
300Mbps Wireless N NAS Rout www.phicomm.com Traffic Statistics This page used to display the current system memory usage, WLAN, LAN and WAN networks to send and receive data packets to the number. Firmware Upgrade You can upgrade the router to the lasted version in this page, please download a most recent firmware upgrade file from our website. After downloading the file, you need to extract the zip file before upgrading the router. Browse for the upgrade file, then click Upgrade button.
300Mbps Wireless N NAS Rout www.phicomm.com during the upgrade could damage the Router. Note: • Router might be changed to factory default settings after upgrade, please backup in advance. • During the updating, please do not turn off the power. • Please make sure the software version is matching with the existing hardware. Reboot Click Reboot button to reboot the Router. Logout Click to logout from the router configuration web.
www.phicomm.com 300Mbps Wireless N NAS Rout Chapter 4: Download Wizard Before you start Before you use the Offline Download Wizard, please make sure: 1. The wireless router is powered on, LAN port goes into the computer, and WAN port goes into modem. 2. The Download function is enabled in the wireless router. 3. The USB storage device is plugged into the USB port of the wireless router. 4. The Offline Download Wizard is installed successfully on your computer. Configuration 1.
www.phicomm.com 300Mbps Wireless N NAS Rout 2. Click Local Settings button, you can see a new page pop up.
www.phicomm.com 300Mbps Wireless N NAS Rout Minimize to tray: check this option, this program will be minimized to tray, you can see a tray icon in the Windows Taskbar. Connect to server at startup: check this option, it will automatically connect to the offline download server when startup. Host IP addr: IP address of the wireless router, the default address is 192.168.0.1 Username: login username for the wireless router’s web management page, the default username is admin.
300Mbps Wireless N NAS Rout www.phicomm.com If it is successfully connected, you can see some shortcut buttons come up in the main page, #: Task ID. Name: The name of download file. Size: The size of the download file, the value is in megabyte (M). Status: It will show downloading, paused, waiting or complete. Done: The percentage of the file that has been downloaded. Speed: The download speed. The Connect button changed into Disconnect button, and Task is available.
www.phicomm.com 300Mbps Wireless N NAS Rout Note: Please follow the instructions according the error messages, click OK button then try to reconnect. 4.
www.phicomm.com 300Mbps Wireless N NAS Rout Note: The pull-down menus for Remote Setting include all the partition of the USB storage device that can be detected, the first partition is /media/sda1, the second partition is /media/sda2, and so on. Click Save button after you choose the partition, then the new task will be downloaded to the assigned partition.
www.phicomm.com 300Mbps Wireless N NAS Rout 5. Click Add button to add task. Protocol Type: the protocol type of the download file, it can be HTTP or FTP. URL: input a legitimate and complete URL address, it can’t be blank. Port: This is optional. If the URL does not include port number, and a special port number is needed, then input that number (must be numbers). Login Info: This is optional. It is available when the Protocol Type is FTP.
www.phicomm.com 300Mbps Wireless N NAS Rout Click Save button after you add task, the new task will appears in the task list, with status showing Downloading. Note: Limited by the wireless router’s CPU and memory, to ensure the stability of the offline downloading, the maximum number of Downloading task is 2. When the number of Downloading task reaches 2, the status of the new task will be turned into Waiting automatically.
www.phicomm.com 300Mbps Wireless N NAS Rout Note: The third button (like a red cross) remove task means remove the selected task, but data already downloaded would be saved. If you click the last button (like a trash can) remove and delete task, all the data will be removed. You can see this message comes up.
www.phicomm.com 300Mbps Wireless N NAS Rout (3) If you select more than one task, you can see the icons below: 7. Main menu (1)File Connect: same as Connect shortcut button. Disconnect: same as Disconnect shortcut button. Add task: same as Add task shortcut button. Exit: exit from the program. (2) Option Local settings: same as Local settings shortcut button. Remote setting: same as Remote settings shortcut button. (3)Task Start: same as Start shortcut button.
www.phicomm.com 300Mbps Wireless N NAS Rout Pause: same as Pause shortcut button. Properties: shows the properties of the selected task. Remove: same as Remove shortcut button. Remove and Delete: same as Remove and Delete shortcut button. Start all: start all the tasks. Pause all: pause all the tasks. (4) Help Click About Download Wizard for HTTP/FTP, you can see a page pop up.
www.phicomm.
300Mbps Wireless N NAS Rout www.phicomm.com Chapter 5: Specification General Standards IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, CSMA/CA with ACK Data Rate 11n: 300Mbps Frequency Range 2.4-2.
300Mbps Wireless N NAS Rout www.phicomm.com 1 x Ethernet Cable * All references to speed and range are for comparison purposes only. Product specifications, size, and shape are subject to change without notice, and actual product appearance may differ from that depicted herein.
www.phicomm.com 300Mbps Wireless N NAS Rout Appendix A: Troubleshooting 1. PHICOMM Setup cannot find my Router. If PHICOMM Setup is not able to communicate with your Router during installation, please check the following items: 1) Ensure that the router and modem are both on. 2) Make sure the computer goes into the LAN port of the router. 3) Make sure the DSL modem goes into the WAN port of the router. 4) There may be firewall software on your computer preventing an outgoing connection.
300Mbps Wireless N NAS Rout www.phicomm.com Explorer as an example, go to Tools>Internet Options>Connections>LAN Settings, uncheck Use a proxy server for your LAN 5) If it tells you the username or password is error, and you cannot remember the new one, please reset router by pressing reset button for at least 6 seconds, and then try to login with default username and password (admin/admin). 4. The computer cannot connect to the Internet.
300Mbps Wireless N NAS Rout www.phicomm.com 5. The computer cannot connect to the internet wirelessly. Please make sure you can access the Internet when plug in the Ethernet cable from the router to the computer, otherwise, please refer to Question 4. Then check the wireless connection status on your computer: 1) Search available networks and connect to your wireless network.
www.phicomm.
300Mbps Wireless N NAS Rout www.phicomm.com Appendix B: Certification FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
www.phicomm.com • 300Mbps Wireless N NAS Rout This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • For product available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible.
300Mbps Wireless N NAS Rout www.phicomm.com Appendix C: Glossary 802.11b: The 802.11b standard specifies a wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. 802.
www.phicomm.com 300Mbps Wireless N NAS Rout DNS (Domain Name System): An Internet Service that translates the names of websites into IP addresses. Domain Name: A descriptive name for an address or group of addresses on the Internet. DSL (Digital Subscriber Line): A technology allowing data to be sent or received over existing traditional phone lines. ISP (Internet Service Provider): A company that can provide access to the Internet.
www.phicomm.com 300Mbps Wireless N NAS Rout communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name. WEP (Wired Equivalent Privacy): A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard. Wi-Fi: A trade name for the 802.
Shanghai Feixun Communication Co., E-mail: support@phicomm.com Website: www.phicomm.com Copyright © 2011 Shanghai Feixun Communication Co., Ltd. All rights reserved.
