WIRELESS EARPHONES with ACTIVE NOISE CANCELLING Thank you for purchasing PHIATON BT 100 NC - Please follow the directions, and read the guidelines carefully before use. Please keep the owner’s guide for future reference. - Some functions of the BT 100 NC may not be available when it is paired with certain devices. - The specifications are subject to change without prior notice for quality improvement. Contents 1. SAFETY AND GENERAL INFORMATION 2. COMPONENTS & FEATURES 3. HOW TO WEAR EARPHONES 4.
1. SAFETY AND GENERAL INFORMATION 1) Use a standard USB charging cable (included), with or without a charging adaptor. (5V, over 500mA) * Adapter Not Included 2) Lower the volume prior to listening to audio to prevent potential damage to eardrums caused by sudden loud sound. 3) Listening to loud music for extended periods of time may cause hearing damage. 4) Do not store the device in places with a temperature higher than 113 ℉/ 45 ℃. 5) This product is sweat and water resistant.
2. COMPONENTS & FEATURES 1) COMPONENTS - BT 100 NC - USB Charging Cable - Audio Cable - 4 Sizes of Silicon Ear Tips - Stoppers - Quick Guide - Warranty Card 2) FEATURES 3. HOW TO WEAR EARPHONES 1) Hold the earphone body with wire dropping down. 2) Gently insert the ear tip into the ear canal. 3) Let the ear tip set comfortably in your ear.
4. CHARGING The device may not be charged upon purchase and must first be charged before use. 1) Open the USB cover on BT 100 NC and connect the provided USB charging cable. 2) Connect the provided USB charging cable with a computer (laptop) or you may also use a separately purchased USB adaptor (rating: 5V/over 500mA) to begin charging. Operation LED Indicator Charging Red light Charging complete Blue light 5.
- Press and hold the [CALL/POWER] Button for 2 seconds to turn the power on. - When turning the power off, press and hold the [CALL/POWER] Button for 2.5 seconds to turn off. (While on an incoming call, you cannot power off the device.) - When turning power on/off, there is a vibration notification that rings. Status Operation LED Indicator Press and hold the CALL/ Purple light turns POWER button for 2 seconds on for 1 second Press and hold the CALL/ Red light blinks POWER button for 2.
※ If the ‘Bluetooth Device’ requires a PIN CODE or password, enter ‘0000’. - Use the earphones to play music or connect a call. Operation LED Indicator Voice Guidance After Purple light blinks twice, Connection success blue light blinks once in 6 second intervals.
- Once the device has been paired with a ‘Bluetooth Device’, it will automatically be connected to a previously connected device once the BT 100 NC power is turned on. - If Bluetooth becomes disconnected as the discover range between the ‘Bluetooth Device’ and the BT 100 NC is exceeded, then Bluetooth will not be automatically re-connected. When you are back within the discover range (33 feet), you must then connect manually.
8. MULTIPOINT CONNECTION 1) What is ‘Multipoint Connection'? This is a feature where BT 100 NC’s user can simultaneously connect two Bluetooth devices. 2) Multipoint Connecting - Turn on the Bluetooth feature within the two 'Bluetooth Devices' you want to connect with BT 100 NC. - Refer to ‘6. PAIRING WITH A ‘BLUETOOTH DEVICE’’ to pair the first device with the BT 100 NC. - Press and hold the PLAY Button again for 2.5 seconds to enter ‘Pairing Mode’. (Here, the first device becomes disconnected.
3) What is ’Auto Mode’? This is a mode used to automatically reconnect both previously connected 'Bluetooth Devices' when the POWER is turned off and back on. 4) Using ‘Auto Mode’ - Within Pairing Mode, press the (+) Button for 2.5 seconds to turn on Auto Mode. - If you press the (+) Button for 2.5 seconds again, then Auto Mode will turn off and switch to Manual Mode. ※ Upon Multipoint Connection, the features operated within BT 100 NC usually operate within the second paired device.
3) Cautions upon using Noise Cancelling Feature - Noise Cancelling cannot be used when the battery is completely drained. - Use while driving or walking will prevent outside noise, such as signals or alarms, from being heard and may be dangerous to yourself and others. Heed caution during use. - Noise Cancelling is optimized for mechanical noises from airplanes, buses, and subway trains and is not required for use within quiet interior environments. 10.
After 1 second, the ‘beep’ signal tone is provided. - Press and hold the (+)/(-) Button continuously to fast-forward / rewind the current song. ※ Music can be listened to through BT 100 NC by directly operating your ‘Bluetooth Device’. ※ When the battery is completely drained, you can connect the provided audio cable to continue listening. 12.
. USING THE CALL FUNCTION 1) Accepting a Call - When the incoming call tone is heard through the earphones or the incoming call vibration is ringing, press the CALL/POWER Button. (Adjusting Call Volume: to control the call volume, press the (+)/(-) Button.) 2) Ending a Call - While on a call, shortly pressing the CALL/POWER Button to end the call.
(Supported within mobile phones that support the voice command feature). - While waiting, shortly press the CALL/POWER Button. 8) Switching between the Device and Mobile Phone - To switch the call from mobile phone to the headphone, press the CALL Button for 1 second. Status LED Indicator Incoming Bell/Outgoing Bell Purple light blinks in 1.
※ Battery use time Classification Noise Cancelling OFF Noise Cancelling ON Continuous Talk Time Max 11 hours Max 7 hours Max 10 hours Max 6 hours Max 12 hours Max 7.5 hours Max 220 hours Max 15 hours Continuous Music Play Time aptX High Quality Sound Mode SBC Mode Stand by Time Full Charge Time About 2 hours ※ The above times may differ depending on the environment in which it is used. 15.
- For Apple iOS version 5 or above, the remaining battery is displayed at the top right side of the screen. * The Battery Check feature will not operate while the battery is being charged. * When the battery charge is under 3%, the alarm will sound. If use is continued for several minutes the battery will be completely drained, the 'Power Off' voice guidance is provided and the power will automatically turn off.
18. SPECIFICATIONS 1) Main Body - Communication Network: Bluetooth 4.0 - Output Power: Power Class 2 - Max. Communication Range: Discoverable within 10 m / 33 ft. - Full Charging Time: 2 Hours - Call Time (NC ON / OFF): 7 Hours / 11 Hours - Music Play Time (NC ON / OFF): 7.5 Hours / 12 Hours - Standby Time (NC ON / OFF): 15 Hours / 220 Hours - Bluetooth Profile Support: HFP v1.6 / HSP v1.2 / A2DP v1.3 / AVRCP v1.5 - Audio Codec: SBC, aptX - Battery: Lithium Polymer DC 3.
19. PRODUCT SYMPTOMS AND TROUBLESHOOTING 1) The power does not turn on: - Charge the device. If the power does not turn on even after charging, contact Phiaton Customer Service. 2) The device does not charge: - Check whether the USB charging cable has been properly connected with the device. - Check whether the PC power is on and that it has been properly connected. - When using a separately purchased USB AC adaptor, check to see that it has been properly connected.
(The LED Indicator feature can be activated by simultaneously pressing the (+) Button and (-) Button for 2.5 seconds.) 10) Product does not operate or operation has stopped: - Shortly press the CALL/POWER Button and (-) Button simultaneously. - Power will turn off once the buttons are pressed. - Pairing information is not deleted even when the device is reset.
This device complies with Industry Canada license-except RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC Radio Frequency (RF) Exposure rules.