User Manual

ManualsBrandsPerimeter Technologies ManualsElectronicsPet Avoidance System

Support / Warranty

EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, NO

OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED,

OTHER THAN THOSE PROVIDED IN WRITING HEREIN, SHALL

APPLY TO THIS UNIT, PERIMETER TECHNOLOGIES, INC. SHALL

NOT BE LIABLE FOR ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

FOR ANY PERIOD IN EXCESS FOR THE PERIODS OF EXPRESS

WARRANTIES PROVIDED ABOVE. IN ADDITION, UNDER NO

CIRCUMSTANCES, SHALL PERIMETER TECHNOLOGIES, INC.

BE LIABLE FOR PROPERTY DAMAGE, ECONOMIC LOSS, OR ANY

CONSEQUENTIAL DAMAGES SUSTAINED IN CONNECTION WITH

SAID UNIT. SOME STATES DO NOT ALLOW LIMITATION ON HOW

LONG AN IMPLIED WARRANTY LASTS, OR DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY

NOT APPLY TO YOU.

PERIMETER TECHNOLOGIES, INC. NEITHER ASSUMES NOR

AUTHORIZES ANY REPRESENTATIVE OR OTHER PERSON TO

ASSUME FOR IT ANY OBLIGATION OR LIABILITY OTHER THAN

SUCH AS IS EXPRESSLY SET FORTH HEREIN. THIS WARRANTY

GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE

OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

Indoor Wireless Transmitter

10000037

Summary of content (8 pages)

PAGE 1
Support / Warranty EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, NO OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED, OTHER THAN THOSE PROVIDED IN WRITING HEREIN, SHALL APPLY TO THIS UNIT, PERIMETER TECHNOLOGIES, INC. SHALL NOT BE LIABLE FOR ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FOR ANY PERIOD IN EXCESS FOR THE PERIODS OF EXPRESS WARRANTIES PROVIDED ABOVE. IN ADDITION, UNDER NO CIRCUMSTANCES, SHALL PERIMETER TECHNOLOGIES, INC.
PAGE 2
Description / Specifications The transmitter can be used in one of two modes, wireless or wired. In wireless mode the transmitter emits a signal radially approximately seven feet. In wired mode, the transmitter will emit a signal strength of approximately four feet on either side of the attached wire. Actual amount of signal generated is a function of wire geometry.
PAGE 3
Cautions Receiver Problem: Receiver is not detecting signal from the wire 1. Make certain that the transmitter is turned on and transmitting. 2. Make certain that the receiver battery is inserted properly. 3. Make cure that the display is reading a 6 or higher. A setting of less than 6 may not detect a break in the wire. Contact your local dealer if none of these resolve the issue. Problem: Pet is not responding to the correction stimulus / training pulse 1. Check the fit or tightness of the collar.
PAGE 4
Agency Certifications Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 5
Operation User Controls Transmitter: Under normal operation, the transmitter will display the signal strength number (such as “10”) and will make no sounds. This indicates the transmitter is operating normally. You may make adjustments to the transmitter to obtain the correction zone you desire. Pressing the upper button (“+”) will increase the field to a maximum of 32. Pressing the lower button (“-“) will decrease the field to a minimum of 1.
PAGE 6
Contents 1 Indoor Wireless Transmitter 1 AC adapter 1 Wired mode adapter cord 1 User Manual 6 The battery should last about 4 months; however, activity of the pet greatly affects the battery life. A well-trained pet, which infrequently challenges the system, will yield a much higher battery life. When it is time to change the battery, the red indicator light on the front of the receiver will begin to flash. The battery should be changed immediately.
PAGE 7
Wireless Operation Place the transmitter in the location you would like the pet to avoid (example, under the couch). Plug the AC adapter into the transmitter (left side as shown in picture below), this turns the unit on. (Make sure the AC adapter is plugged into the LEFT side, marked “Power”). Adjust the range by pushing the upper (“+ “ to increase) and/or lower (“-“ to decrease) buttons. A mounting option has been provided if you would like to permanently mount the unit.
PAGE 8
Wired Operation Receiver Collar Setup Take the wired mode adaptor cord provided (plug on one end, two wires on the other end) and attach each end to a loop wire utilizing standard electrical techniques; as in crimping the wires together, pig tails, or simply twisting them together using electrical tape to insulate the connections. Attach/plug in the wired mode adaptor plug with loop wire into the RIGHT side, marked “Loop”.