Configuring the Cellular Router Step 1. Enable the SIM Injector communication protocol. 1a. If you are using a Balance cellular router, go to the Network tab (top navigation bar). 1b. If you are using a MAX cellular router, go to the Advanced tab (top navigation bar). 2. Under Misc. settings (left navigation bar) find Remote SIM Management. 3. In Remote SIM Management, click on the edit icon next to Remote SIM is Disabled. 4. Check the Auto LAN discovery checkbox and click Save and Apply Changes. 5.
4. Enter configuration settings in Remote SIM Settings section. Click on Scan nearby remote SIM server to show the serial number(s) of the connected SIM Injector(s). Available configuration options for cellular interface are shown below: A. Defining SIM Injector(s) - Format: - Example 1: 1111-2222-3333 - Example 2: 1111-2222-3333 4444-5555-6666 B.
Scenario 2: SIM Injector in WAN of main Router and multiple Cellular Routers Setup topology In this scenario, each HD Dome creates a WAN connection to the main router. A single SIM Injector is used to provide SIM cards for each HD Dome. The HD Dome can be replaced with any Peplink cellular router supporting RemoteSIM technology. This scenario requires the completion of the configuration steps shown in Scenario 1 in addition to the configuration steps explained below.
1. Go to Network (Top tab), then Network Settings (Left-side tab), and click on Untagged LAN. This will open up the LAN settings page. 2. Change the IP address to 192.168.50.2. 3. In the DHCP Server section, uncheck the checkbox to disable DHCP Server. 4. Click Save and Apply Changes. Step 2. Ethernet port configuration The Ethernet port must be set to ACCESS mode for each HD Dome. To do this, dummy VLANs need to be created first. 1.
6. Click Save and Apply Changes. Configuration requirements for the main Router Requirements for the main router are: - Configure WAN 1 as a DHCP client. - WAN 1 will automatically get the Gateway IP address from HD Dome 1. - Configure WAN 2 as a Static IP and set it to 192.168.50.12. - Configure WAN 2 Gateway to 192.168.50.2. Same as the HD Dome 2’s IP address.
Scenario 3: SIM Injector in LAN of main Router and multiple Cellular Routers Setup topology In this scenario, SIMs are provided to the HD Domes via the main router. In this example, the Remote SIM Proxy functionality needs to be enabled on the main router. Notes: - HD Dome can be replaced with any other cellular router that supports RemoteSIM.
- It is recommended to use Peplink Balance series or X series routers as the main router. This scenario requires the completion of the configuration steps for the cellular router and the SIM Injector as in Scenario 1. The configuration for the main router is explained below. Main Router configuration IMPORTANT: Main router LAN side and Cellular Routers must be configured using different subnets, e.g. 192.168.50.1/24 and 192.168.100.1/24. Note: please make sure the Peplink router is running Firmware 8.1.
Scenario 4: SIM Injector in a remote location Setup topology Requirements for installing a SIM Injector in a remote location: ● ● ● ● Cellular router communicates with the SIM Injector via UDP port 50000. Therefore this port must be reachable via public IP over the Internet. The one way latency between the cellular router and the SIM Injector should be up to 250 ms. A higher latency may lead to stability issues. The cellular router must have Internet connection to connect to the SIM Injector.
2. Under Misc. settings (Left-side tab), find Remote SIM Management. 3. In Remote SIM Management, click on the edit icon next to Remote SIM is Disabled. 4. Enter the public IP of the SIM Injector and click Save and Apply Changes. Notes: - Do NOT check Auto LAN Discovery. Do NOT add a SIM Injector serial number to the Remote SIM Host field. Step 2. RemoteSIM and custom SIM card settings configurations are the same as in Scenario 1.
How to check if a Pepwave Cellular Router supports Remote SIM 1. Go to Network (Top tab), then WAN (Left-side tab), and click Details on any cellular WAN. This will open the WAN Connection Settings page. 2. Scroll down to Cellular settings. If you can see the Remote SIM Settings section, then the cellular router supports Remote SIMs. Monitor the status of the Remote SIM 1. Go to Network (Top tab), then WAN (Left-side tab), and click Details on the cellular WAN which was configured to use RemoteSIM. 2.
Appendix C: Overview of ports used by Peplink SD-WAN routers and other Peplink services Default Port Number Usage Service Inbound/Outbound Default Status UDP 5246 Data flow InControl Outbound Enabled TCP 443 HTTPS service InControl Outbound Enabled TCP 5246 Optional, used when TCP 443 is not responding InControl Outbound Enabled Outbound Enabled InControl Virtual Appliance TCP 5246 Remote Web Admin TCP 4500 VPN Data (TCP Mode) PepVPN / SpeedFusion Inbound / Outbound* Disabled TC
Interface access TCP 443 HTTPS traffic Web Admin Interface access (secure) TCP 8822 SSH SSH Inbound Disabled UDP 161 SNMP Get SNMP monitoring Inbound Disabled UDP 162 SNMP Trap SNMP monitoring Outbound Disabled TCP, UDP 1812 Radius Authentication Radius Outbound Disabled TCP, UDP 1813 Radius Accounting Radius Outbound Disabled UDP 123 Network Time Protocol NTP Inbound Outbound Disabled Enabled TCP 60660 Real-time location data in NMEA format GPS Outbound Disabled Inboun
Appendix D: Declaration FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 Mini This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CE Statement for Pepwave Routers ( MAX BR1 Mini for EC25-E)
2.4GHz ( 2412 – 2472 MHz ) : 16.38 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( MAX BR1 Mini for MC7455)
2.4GHz ( 2412 – 2472 MHz ) : 16.38 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
Industry Canada Statement (for MAX BR1 Mini) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
FCC & IC Requirements for Operation in the United States and Canada (for MAX BR1 Mini) FCC ID : U8G-P1930LITER6 FCC 15.21: The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Informations concernant l'exposition aux frequences radio (RF) Cet equipement est conforme avec l'exposition aux radiations IC definies pour un environnement noncontrole. Cet equipement doit etre installe et utilise a une distance minimum de 20 cm entre le radiateuret votre corps. Cet emetteur ne doit pas etre co-localisees ou operant en conjonction avec une autreantenne ou transmetteur.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 MK2 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
exempts de licence.
CE Statement for Pepwave Routers ( MAX BR1 MK2 )
2.4GHz ( 2412 – 2472 MHz ) : 19.95 dBm 5GHz ( 5150 - 5250 MHz ) : 22.73 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 Classic This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Industry Canada Statement ( for MAX BR1 Classic ) This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions (1) This device may not cause interference; and(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
CE Statement for Pepwave Routers ( MAX BR1 Classic for MC7455)
2.4GHz ( 2412 – 2472 MHz ) : 19.78 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( MAX BR1 Classic for EC25-E)
2.4GHz ( 2412 – 2472 MHz ) : 19.78 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX HD4 MBX, MAX HD2 MBX This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement économique Canada. (i) The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p.
Battery Caution Statement (MAX HD4 MBX) Risk of explosion if the battery is replaced by an incorrect type.
CE Statement for Pepwave Routers ( MAX HD4 MBX For EM7565 )
2.4GHz ( 2412 – 2472 MHz ) : 19.6 dBm 5GHz ( 5150 - 5250 MHz ) : 19.4 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( MAX HD2 MBX / MAX HD4 MBX For LM960A18)
2.4GHz ( 2412 – 2472 MHz ) : 19.6 dBm 5GHz ( 5150 - 5250 MHz ) : 19.4 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX HD2 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
(i) The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and The high-power radars are allocated as primary users (i.e.
CE Statement for Pepwave Routers ( MAX HD2 For MC7455)
2.4GHz ( 2412 – 2472 MHz ) : 19.90 dBm 5GHz ( 5150 - 5250 MHz ) : 22.88 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( MAX HD2 For MC7565)
2.4GHz ( 2412 – 2472 MHz ) : 19.86 dBm 5GHz ( 5150 - 5250 MHz ) : 22.68 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
( For MAX BR1 Classic CB IEC 62368-1 ) Mounting the Unit Wall Mount The Pepwave MAX BR1 Classic can be wall mounted using screws. After adding the screw on the wall, slide the MAX in the screw hole socket as indicated below. Recommended screw specification M3.5 x 20mm, head diameter 6mm, head thickness 2.4mm. The Pepwave MAX BR1 Classic requires four screws for wall mounting.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 Pro 5G FCC 15.21 The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Industry Canada Statement ( MAX BR1 Pro 5G ) This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
antenna gain for 2.4GHz 2.44 dBi antenna gain for 5GHz ( 5150 ~ 5250 MHz ) 4.10 dBi antenna gain for 5GHz ( 5725 ~ 5850 MHz ) 4.73 dBi Battery Caution Statement Risk of explosion if the battery is replaced by an incorrect type.
CE Statement for Pepwave Routers ( MAX BR1 Pro 5G)
2.4GHz ( 2412 – 2472 MHz ) : 19.74 dBm 5GHz ( 5150 - 5250 MHz ) : 22.66 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 Mini Core This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX 700 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
For MAX HD2 IP67, MAX HD2 Mini, MAX HD2 Dome, MAX HD4 IP67, MAX BR1 ENT, MAX BR1 M2M, SpeedFusion Engine Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CE Statement for Pepwave Routers ( MAX HD2 IP67 )
WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( MAX HD1 Dome )
WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( MAX HD2 Dome )
WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( MAX BR1 ESN )
2.4GHz ( 2412 - 2472 MHz ) : 19.78 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX HD4 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en (i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complie
CE Statement for Pepwave Routers ( MAX HD4 )
2.4GHz ( 2412 - 2472 MHz ) : 18.87 dBm 5GHz ( 5150 - 5250 MHz & 5725 - 5850 MHz ) : 19.13 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( MAX HD4 IP67 )
WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( SpeedFusion Engine )
WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) MC7455 module: EC25-E module: This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX Transit, MAX Transit Duo Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
tion of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
CE Statement for Pepwave Routers ( MAX Transit / MAX Transit Duo For EM7565 )
2.4GHz ( 2412 - 2472 MHz ) : 18.68 dBm 5GHz ( 5150 - 5250 MHz ) : 18.19 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( MAX Transit For LM960A18 )
2.4GHz ( 2412 - 2472 MHz ) : 18.68 dBm 5GHz ( 5150 - 5250 MHz ) : 18.19 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX Transit Mini Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This radio transmitter has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna types Replacement Antenna Antenna gain (in dBi) 5.
CE Statement for Pepwave Routers ( MAX Transit Mini )
2.4GHz ( 2412 - 2472 MHz ) : 19.78 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 PRO, MAX BR2 PRO, UBR LTE Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
For licence exempt equipment with detachable antennas, the user manual shall also contain the following notice in a conspicuous location: This radio transmitter 20682-P1941 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Radiation Exposure Statement This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 23 cm between the radiator & your body. Cet equipement est conforme avec l'exposition aux radiations ISED definies pour un environnement non controle. Cet equipement doit etre installe et utilise a une distance minimum de 23 cm entre le radiateur et votre corps.
CE Statement for Pepwave Routers ( MAX BR1 PRO / MAX BR2 PRO / UBR LTE )
2.4GHz ( 2412 - 2472 MHz ) : 19.94 dBm 5GHz ( 5150 - 5250 MHz ) : 20.34 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 IP55, MAX BR2 IP55 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CE Statement for Pepwave Routers ( MAX BR1 IP55 )
2.4GHz ( 2412 - 2472 MHz ) : 18.16 dBm 5GHz ( 5150 - 5250 MHz) : 20.32 dBm 5GHz ( 5725 - 5850 MHz) : 13.00 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 50cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( MAX BR2 IP55 )
2.4GHz ( 2412 - 2472 MHz ) : 18.99 dBm 5GHz ( 5150 - 5250 MHz ) : 22.95 dBm 5GHz ( 5725 - 5850 MHz ) : 12.80 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 50cm between the radiator & your body. contact as: https://www.peplink.
USB WAN Modem Port Specification MAX Series Output Rating MAX 700 MAX HD2 / MAX HD2 Media Fast MAX HD2 Mini MAX HD2 / HD4 MBX MAX BR1 ENT MAX BR1NT MAX HD4 / MAX HD4 Media Fast / MediaFast 200 5V DC, 2A 5V DC, 2A 5V DC, 2A 5V DC, 0.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX Transit Pro E / MAX Transit LTEA FCC 15.21: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. FCC 15.105 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
ICES Statement This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement économique Canada. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1.
This radio transmitter IC: 20682-P1835 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Cet émetteur radio IC : 20682-P1835 a été approuvé par Innovation, Sciences et Développement économique Canada doit fonctionner avec les types d'antennes énumérés ci-dessous, avec le gain maximal admissible indiqué. Les types d'antenne non inclus dans cette liste qui ont un gain supérieur au gain maximum indiqué pour tout type répertorié sont strictement interdits pour une utilisation avec cet appareil.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX Transit Pro Federal Communication Commission Interference Statement Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
(i) The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potent for harmful interference to co-channel mobile satellite systems; (ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; (detachable antenna only) ; and The high-power radars are allocated as primary users (i.e.
This radio transmitter IC: 20682-P1AX11 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. WIFI Antenna type: Omni-directional WIFI Antenna gain: 2.4GHz / 2.44 dBi 5150 ~ 5250 MHz / 4.10 dBi 5725 ~ 5850 MHz / 4.