QuickTouch® II Wireless Remote (For EasyTouch®, IntelliTouch® SunTouch® and Compool ® CP3800 Series Control Systems) PR I L E N I M Y R A Installation and User’s Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS QuickTouch® II Wireless Remote Installation and User’s Guide
Technical Support Phone: (800) 831-7133 - Fax: (800) 284-4151 visit www.pentairpool.com and www.staritepool.com: © 2010 Pentair Water Pool and Spa, Inc. All rights reserved. 1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000 10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000 QuickTouch®, IntelliTouch®, EasyTouch®, SunTouch® and Pentair Water Pool and Spa® is a registered trademark of Pentair Water Pool and Spa, Inc.
WARNING AND IMPORTANT SAFETY INSTRUCTIONS SERIOUS BODILY INJURY OR DEATH CAN RESULT IF THIS PRODUCT IS NOT INSTALLED AND USED CORRECTLY. INSTALLERS, POOL OPERATORS AND POOL OWNERS MUST READ THESE WARNINGS AND ALL INSTRUCTIONS BEFORE USING THE POOL AND/OR SPA LED LIGHT. Most states and local codes regulate the construction, installation, and operation of public pools and spas, and the construction of residential pools and spas.
WARNING AND IMPORTANT SAFETY INSTRUCTIONS CAUTION: IMPORTANT BATTERY INFORMATION • Danger of explosion if battery is incorrectly replaced. • ONLY USE a Pentair Water Pool and Spa replacement battery. Order Battery Replacement Kit (P/N 520815Z). • Rechargeable Lithium-ion battery disposal: Unwanted lithium ion battery pack may be returned to your local recycling center or the manufacturer for disposal. • Dispose of used batteries according to the manufacturer’s instructions.
QuickTouch II Wireless Remote Overview The QuickTouch II wireless remote remote is a double-insulated device for use with EasyTouch®, IntelliTouch®, SunTouch® and Compool (CPxxxx) pool and spa control systems. EasyTouch, IntelliTouch, SunTouch and Compool control systems supports one QuickTouch II wireless remote per system. The QuickTouch II wireless remote may be used with wet hands. To aviod damage to the remote, never submerge in water.
QuickTouch II Wireless Remote Buttons/LEDs Auxiliary Circuit Buttons (1-4): Circuit button one is assigned to spa/heat control. Buttons 1 - 4 are assigned to AUX 1- AUX 4). Note: Circuit buttons can be reassigned to any relay circuit. Auxiliary Circuit Buttons (5-6): Circuit button six is assigned to pool/filter control. Buttons 5 - 8 are assigned to AUX 7- AUX 8). Note: Circuit buttons can be reassigned to any relay circuit. LED: This LED will illuminate when the unit is receiveing and transmitting.
Operating QuickTouch II Wireless Remote The spa-side remote can control up to eight system functions, depending on the system being used (EasyTouch®, IntelliTouch® and Compool®). Each circuit function can be labeled above the buttons to identify the button function. An LED indicator indicates the circuit is active. Note: For IntelliTouch system only: IntelliTouch supports multiple spaside remote. For more information about connecting and configuring multiple remotes, see page 15.
Connecting QuickTouch II 1. To enter the ID programming mode press buttons 2 and 6 at the same time. 2. The LED will flash slowly 4 times while entering the ID programming mode. At a 1 second on/off pulse rate. 3. Enter the 8 bits of identification number where Switch 1 is button 1, switch 2 is button 2 through to switch 8 as button 8. 4. Note: During programming of the ID, only press the buttons that are to be set high or “1”. The equivalent switch on the receiver is in the on position.
The example in figure 2 shows an ID number equal to button one (1) only active or equal to a press during programming. Buttons 2 through 8 do not required a press. Switch 9 and 10 on the receiver are always in the off position. The example in figure 3 shows an ID number equal to button one (1) through eight (8) all active or equal to a press during programming. All buttons are press once. Switch 9 and 10 on the receiver are always in the off position.
INTELLIBRITE 5g POOL LED LIGHT FIXTURE INSTALLATION WIRING THE QUICKTOUCH II TRANSCEIVER TO THE LOAD CENTER (NEW POOL CONSTRUCTION) All electrical installation, including electrical wiring methods and materials used to complete the electrical installation of the EasyTouch and IntelliTouch Pool/Spa control system MUST BE PERFORMED BY A SERVICE PROFESSIONAL AND/OR UNDER DIRECT SUPERVISION OF A QUALIFIED ELECTRICIAN in accordance with the National Electrical Code or the Canadian Electric Code, as well as a
5. 6. 7. Insert the four-wire cable into the plastic grommet on the bottom of the enclosure and route the wire up through the low voltage raceway to the main circuit board. Strip back the cable jacket 1-inch and the cable conductors ¼-inch. EasyTouch System: Insert the wires into the COM PORT (J20) screw terminals located on the top of the EasyTouch circuit board (see diagram below). Secure the wires with the screws. For wiring details, refer to the pin configuration shown below.
QuickTouch II Wireless Remote Receiver Antenna Location The optimum wireless transmit and receive range for the QuickTouch II receiver may be affected by physical obstructions, (especially those containing metal), weather conditions, and geographical features. The QuickTouch II wireless remote has an operating range of up to 500 ft. (line-of-sight) from the receiver. The receiver kit includes a 10 ft. connection cable. If needed, using extra cable, the cable length can be lengthened to 300 ft.
Installing the Receiver The QuickTouch II wireless remote has an operating range of up to 500 ft. (line-of-sight) from the receiver. To install the receiver: 1. 2. 3. 4. 5. 6. 7. 8. 9. Choose an installation location for the receiver near the load center. Remove the two lower retaining screws from the receiver and slide the receiver case up to remove it from the back plate. Remove the receiver circuit board from the back plate by carefully lifting it up out of the back plate supports.
REPLACING THE INTELLIBRITE 5G POOL LED LIGHT FIXTURE (AFTER ELECTRICAL REQUIREMENTS ARE MET) Case Antenna Transceiver circuit board Upper mounting point (screw) 1 GND B LK 2 - DT GRN 3 + DT YEL 4 15V R ED Upper mounting point (screw) Back plate Lower mounting point (screw) Lower mounting point (screw) Left-side Transceiver circuit board support Lower exit hole (left side) Retaining screws Transceiver Module QuickTouch® II Wireless Remote Installation and User’s Guide
Optional Serial COM Port Expansion Board (for use with IntelliTouch® control systems) If there is not an available COM port for the Transceiver cable plug on the IntelliTouch Personality board, the optional Serial COM port Expansion Board (P/N 520818) can be used for additional COM ports connections. Mounting the Expansion Board 1. Remove the inside terminal connectors (with wires attached) from the Expansion board and connect it to a COM port on the Personality board.
Connecting the Transceiver cable plug to the Serial Com Port Expansion Board Connect the Transceiver cable plug onto one of the available Serial COM port expansion board connector terminals.
Setting up QuickTouch II Wireless Remote (EasyTouch) From the EasyTouch control panel menu, you can specify any SpaCommand spa-side remote button to control different functions by assigning each button to a specific circuit. The spa-side remote has 10 assignable circuit buttons; five button on the top row and five buttons on the bottom row. The following setup instructions are described in the EasyTouch User’s Guide (P/N 520584).
COMPOOL SS8 REMOTE UPGRADE INSTALLATION Connecting the spa-side remote to a CP3xxx load center using adapter Strip back the cable 1-inch and ends of leads ¼-inch. Open the cable adapter (P/N 520000, included in kit). Insert the spa-side remote cable into the adapter and attach wires to the terminals (see the wiring diagram below). Attach the six conductor flat cable pig-tail between cable adapter and the COM port connector on the circuit board in the Compool load center.
Changing the Battery With normal use the battery should last for several years. In the event the battery must be replaced, slide the coverfrom the bottom of the Hand-held Remote. Slide the battery from the retainer clip and discard in accordance withlocal and/or state ordinances. Replace with 3V lithium battery number CR2032 or equivalent. Slide battery coveronto remote and snap in place. When you are not using the MobileTouch controller, place it in the cradle to recharge the battery.
Troubleshooting QuickTouch II wireless remote (P/N 520189) Replacement Kit Part Numbers QuickTouch® II Wireless Remote Installation and User’s Guide
QuickTouch® II Wireless Remote Installation and User’s Guide
P/N 521362 Rev A QuickTouch® II Wireless Remote Installation and User’s Guide