User's Manual

ManualsBrandsPella ManualsElectronics433.92 MHz Transceiver

Insynctive™ WOOD VENETIAN BLIND

Product Guide

WOOD BLIND OVERVIEW:

Pella® Wood Blinds can raise, lower or tilt for flexible light or privacy control — all with the press of

a button. WOOD BLIND may be controlled with SINGLE CHANNEL REMOTE, a compatible security, or a

home automation system. Three custom positions may be programmed to WOOD BLIND including an

Upper Position, User Position, and Lower Position.

TOOLS REQUIRED

Measuring Tape

Drill with 3/32” Bit and 1/4” Nut Driver

Pencil

#2 Phillips Head Screwdriver

Flat Head Screwdriver

Level

INSTALLATION AND SETUP INSTRUCTIONS

1. Get Started

Verify package contents match the packing slip

Verify there are no obstructions in the path the shade will travel such as latches, locks, window

crank, handles, sensors, window mullions, etc.

2. Determine Mount Type

Determine whether you will use an Outside Mount or Inside Mount.

3. Install Shade

Measure 6 inches inward from each side of the opening. Mark with a pencil. If your shade has

more than two brackets, the remaining brackets must be distributed evenly between the two

marks. Temporarily place each bracket and mark the screw holes.

Drill holes at the marked locations using a 3/32” bit.

Align bracket and bracket spacer with drilled holes and drive a screw into each hole with a 1/4”

nut driver. Use expansion anchors or toggle bolts if adequate structure is not present in the

mounting area. Repeat for each bracket.

Hook the shade on the brackets by sliding the top leg of the brackets into the top of the shade,

then pressing up at an angle until the shade snaps into the bracket. Inspect behind the shade to

ensure that the shade assembly is secured to each bracket.

4. Setup WOOD BLIND

Complete the following steps to setup WOOD BLIND

Summary of content (7 pages)

PAGE 1
Insynctive™ WOOD VENETIAN BLIND Product Guide WOOD BLIND OVERVIEW: Pella® Wood Blinds can raise, lower or tilt for flexible light or privacy control — all with the press of a button. WOOD BLIND may be controlled with SINGLE CHANNEL REMOTE, a compatible security, or a home automation system. Three custom positions may be programmed to WOOD BLIND including an Upper Position, User Position, and Lower Position.
PAGE 2
a. Remove the front plastic cover and install provided D cell batteries. You have one minute to complete the next step. b. Press and hold UP button on REMOTE until WOOD BLIND completes a quick down/up motion. This will require the UP button to be pressed for about 5 seconds. WOOD BLIND will then move back to the top, fully open position. c. When WOOD BLIND stops in the fully open position, press and release the DOWN button to send the WOOD BLIND to its Lower Position.
PAGE 3
Press the UP or DOWN buttons on REMOTE to move WOOD BLIND Bottom Rail to the desired position. Press and hold the CENTER button until WOOD BLIND makes a quick up/down movement. This should take about 5 seconds. The light on the remote will stop blinking. Programming User Position Simultaneously press and hold the UP and DOWN buttons until WOOD BLIND completes a quick up/down motion. This will require the buttons to be pressed for about 5 seconds.
PAGE 4
While WOOD BLIND is moving, pressing any button on REMOTE will cause movement to STOP. TILTING BLIND SLATS • To enter tilt mode, press and hold the Center button on. REMOTE until light turns solid red. • Press and release the Up button to rotate the slats up. • Press and release the Down button to rotate the slats down. • REMOTE will exit tilt mode after 10 seconds of no activity or when Center button is pressed and held until the light turns off.
PAGE 5
Battery life is up to 5 years, dependent upon size of WOOD BLIND and usage. When the batteries become low, WOOD BLIND motion will slow down and eventually stop. If WOOD BLIND is connected to a compatible security or home automation system, a low battery warning will be sent to the system. To change the batteries follow the steps below. Remove WOOD BLIND’s valance cover by pulling outward and upward from the bottom front lip of the cover. Remove the used batteries.
PAGE 6
Press and hold the UP button on REMOTE until WOOD BLIND completes a quick up/down motion. WOOD BLIND will then move to top. Replace the valance cover. FACTORY RESET This procedure will reset WOOD BLIND to Factory Default conditions. All remotes will be removed from WOOD BLINDS memory and all Positions will be restored to the original settings from the Factory. Press the UP button to move WOOD BLIND to Upper Position. Press and hold the UP button and WOOD BLIND will begin moving down.
PAGE 7
moves all the way to the top. Failure to adhere to the warnings below may result in death, serious injury and/or loss of valuables. Ensure that path of shade is clear before operating. Keep sources of flame away from shades as fabric may be flammable. Do not allow children to operate shades or blinds without proper adult supervision. Keep battery and other small parts out of reach of children. If swallowed, immediately seek medical help. Batteries carry the risk of fire, explosion and burns.