User's Manual

ManualsBrandsPella ManualsElectronicsDead Bolt Door Sensor

Gayle-OBrien-C02L80FZFFRR (3)

ENTRY DOOR

DEADBOLT SENSOR

QUICK START GUIDE

1. Get Started

• Plug BRIDGE into electrical outlet

(light will turn green and then ﬂ ash blue).

NOTE: Follow Bridge Quick Start Guide to set up BRIDGE.

2. Prepare SENSORS

• Use flathead screwdriver to remove

battery cover from LOCK SENSOR.

• Remove battery and plastic tab from

LOCK SENSOR. Reinsert battery.

• Remove plastic tab from OPEN/CLOSE

SENSOR battery.

• Replace battery covers. (OPEN/CLOSE

SENSOR battery cover is included in a bag

within package.)

NOTE: You will have 2 minutes to sync your SENSORS

once the plastic tabs are removed. If 2 minutes pass

without a successful sync, remove and insert the

battery again.

3. Sync SENSORS to BRIDGE

• Press and release the Sync button on BRIDGE

(button nearest the light). Orange light will ﬂ ash

continuously. BRIDGE is in sync mode while the

light is ﬂ ashing orange.

• Depress LOCK SENSOR plunger twice within

2 seconds.

• Green light on BRIDGE and beep will

indicate success.

• Touch OPEN/CLOSE SENSOR to the recessed

line at the top of LOCK SENSOR, and separate

by at least 1 inch. Repeat twice within 2 seconds.

• Green light on BRIDGE and beep will

indicate success.

• To exit sync mode: press and hold Sync button

on BRIDGE until light stops ﬂ ashing orange.

Depress twice within 2 seconds.

5. Install OPEN/CLOSE SENSOR

• Open the door and locate the black plastic

cover on the side of the door panel above the

deadbolt.

• Use a ﬂ athead screwdriver to remove the black

plastic cover.

• Insert OPEN/CLOSE SENSOR until it is ﬂ ush

with the edge of the door panel.

4. Install LOCK SENSOR

• Open the door and locate the deadbolt

strike plate.

• Use a Phillips-head screwdriver to remove

the deadbolt strike plate screws.

• Remove the deadbolt strike plate and black

plastic insert.

• Visit Insynctive.Pella.com/EntryDoor

DeadboltSensor for speciﬁ c Entry Door

Deadbolt Sensor installation instructions, as

requirements vary by door type.

6. Test SENSORS

• Unlock your entry door with SENSORS installed,

and BRIDGE should beep twice.

• Open your entry door with SENSORS installed,

and BRIDGE should beep twice.

WARNING! OPEN/CLOSE SENSOR may indicate a closed

status when door is not completely closed. See Product

Guide on Insynctive.Pella.com for complete review of

ENTRY DOOR DEADBOLT SENSOR operation.

If you will be using the Pella® Insynctive

™

STATUS INDICATOR to

monitor your entry doors, please reference the Quick Start Guide

in the STATUS INDICATOR package to sync.

HAVE A HOME AUTOMATION OR SECURITY SYSTEM?

For instructions on how to sync a Pella Insynctive ENTRY DOOR

DEADBOLT SENSOR to it, visit Insynctive.Pella.com/HomeAutomation.

NEED HELP WITH THE STEPS ABOVE?

Find troubleshooting information and videos at

Insynctive.Pella.com/Support or call 855-473-5524.

WANT TO EASILY REGISTER PELLA INSYNCTIVE PRODUCTS?

Visit Insynctive.Pella.com/Registration for instant access to

instructions, warranties and how-to videos.

FCC Compliance and Industry Canada

This equipment has been tested and found to comply with the limits for Class B

digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a different circuit from the receiver.

• Consult the dealer or an experienced radio/TV contractor for help.

Changes or modiﬁ cations not expressly approved by Pella Corporation could

void the user’s authority to operate the equipment.

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Cet appareil est conforme avec Industrie Canada exempts de licence standard

RSS. L’opération est soumise aux deux conditions suivantes: (1) cet appareil ne

peut causer d’interférences, et (2) cet appareil doit accepter toute interférence,

y compris les interférences qui peuvent causer un mauvais fonctionnement de

l’appareil.

FCC ID: SO7-205Y0000 FCC ID: SO7-205Z0000

IC ID: 11009A-205Y0000 IC ID: 11009A-205Z0000

LIGHT

SYNC BUTTON

LOCK

SENSOR

OPEN/CLOSE

SENSOR

DEADBOLT

STRIKE PLATE

OPEN/CLOSE

SENSOR

LOCK

SENSOR

Separate by at least 1 inch

twice within 2 seconds.

DEADBOLT

BRIDGE

LIGHT

SYNC BUTTON

BRIDGE

WHAT’S INCLUDED:

• ENTRY DOOR LOCK SENSOR: SENSOR will transmit a signal to BRIDGE

when deadbolt is locked or unlocked.

• ENTRY DOOR OPEN/CLOSE SENSOR: SENSOR will transmit a signal to

BRIDGE when the door is opened or closed.

• ENTRY DOOR OPEN/CLOSE SENSOR BATTERY COVER

• QUICK START GUIDE

WHAT’S REQUIRED:

• BRIDGE (required — sold separately): Wirelessly connects your Insynctive

products to STATUS INDICATOR or a compatible security or home

automation system.

• STATUS INDICATOR (optional — sold separately): Lights indicate status of

Pella® Insynctive SENSORS. Or you can use a compatible security or home

automation system to monitor your entry door.

• PELLA ENTRY DOOR PREPPED FOR ENTRY DOOR DEADBOLT SENSOR

• FLATHEAD SCREWDRIVER

• PHILLIPS-HEAD SCREWDRIVER

• DRILL AND 1/8-INCH DRILL BIT

Scan the QR Code® or visit Insynctive.Pella.com/

EntryDoorDeadboltSensor for complete Product Guide

and warnings, instructional videos and other Pella®

Insynctive

™

quick tips.

This Quick Start Guide is intended only to provide an overview

of the product and its use. Before using this product, read the

complete Product Guide and warnings.

Failure to adhere to the warnings below may result in death, serious injury

and/or loss of valuables.

• Pella® Insynctive

™

products are not 100% reliable for a variety of reasons (see

Product Guide and the Warning in Step 6 of this Quick Start Guide for more

information). Therefore, Pella Insynctive products should not be relied upon

in situations where life, safety and/or protection of valuables are solely

dependent on their function. Test each product at least once per year to

help ensure proper operation.

• Pella Insynctive products are not a substitute for careful adult supervision

of children.

• Keep battery and small parts out of reach of children. If swallowed,

immediately seek medical help.

Read the complete Product Guide for additional warnings and information.

WARNING

IQSGED0414

PLASTIC

TAB

Summary of content (2 pages)

PAGE 1
4. Install LOCK SENSOR 1. Get Started ENTRY DOOR DEADBOLT SENSOR BRIDGE SYNC BUTTON • Plug BRIDGE into electrical outlet (light will turn green and then flash blue). NOTE: Follow Bridge Quick Start Guide to set up BRIDGE. LIGHT • Open the door and locate the deadbolt strike plate. • Use a Phillips-head screwdriver to remove the deadbolt strike plate screws. • Remove the deadbolt strike plate and black plastic insert. • Visit Insynctive.Pella.
PAGE 2
4. Instale el SENSOR DE BLOQUEO 1. Empiece PUENTE SENSOR PARA PESTILLO DE PUERTA DE ENTRADA GUÍA DE INICIO RÁPIDO Esta guía de inicio rápido está diseñada únicamente con la finalidad de brindar una descripción general del producto y de su uso. Antes de usar el producto, lea toda la guía del producto y las advertencias. Escanee el QR Code® o visite Insynctive.Pella.