User Manual

ManualsBrandsPelican Accessories ManualsElectronicsG3 Wireless Controller

Instruction for Operation:

Wireless with Rumble

LIMITED WARRANTY

Pelican Accessories warrants to the original consumer purchaser that

the product will be free from defects in materials and / or workmanship

for a period of 120 days from the date of purchase. If a defect covered

by this warranty occurs during this period, Pelican Accessories at its

option will repair or replace, at no charge, any part that Pelican Accessories

determines to be defective.

To obtain warranty service during the warranty period, send the defective

product postage pre-paid, with a money order for $4.00 to cover the

return postage and handling, along with proof of purchase and the date

of purchase to:

PELICAN ACCESSORIES

1840 East 27th Street

Vernon, CA 90058

This warranty shall not apply if the product has been damaged by abuse,

misuses, negligence, accident, modification, tampering or by any other

causes unrelated to defective materials and / or workmanship.

Repair or replacement as provided under this warranty is Pelican

Accessories' exclusive prerogative. ANY APPLICABLE IMPLIED

WARRANTIES, INCLUDING WARRANTIES OR MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE ARE HERBY LIMITED

TO 120 DAYS FROM THE DATE OF PURCHASE AN ARE SUBJECT

TO THE CONDITIONS SET FORTH IN THIS LIMITED WARRANTY. IN

NO EVENT SHALL PELICAN ACCESSORIES OR INCIDENTAL

DAMAGES RESULT FROM THE BREACH OF ANY EXPRESS OR

IMPLIED WARRANTIES. This warranty gives you specific legal rights,

and you may also have other legal rights,

Which vary from state to state.

Pelican and its logo are registered trademarks.

GameCube™ is a registered trademark of

Nintendo of America, Inc.

This product is not desgined, manufactured, sponsored

or endorsed by Nintendo of America, Inc.

Instruction for Operation:

PL-7008

Wireless with Rumble

Our products are developed, tested, and approved by gamers for

gamers. Pelican’s Gamer’s Guarantee states: If you are not 100%

satisfied with your new G3 Wireless controller we will replace it

or replace it with an equal valued item.

SIGNAL

CHANNEL

1 2 3 4

OFF ON RUMBLE

START / PAUSE

OFF

SIGNAL

POWER

B A

BAND

Left & Right Triggers

Turbo Button

Analog

Stick

D-Pad

Power On/Off-rumble Off Switch

A/B Band

Switch

Channel Switch

Action

Buttons

Signal LED

(Yellow)

Start/

Pause

Analog

Stick

A B

BAND

Link LED (Green)

Signal LED (Yellow)

Power LED (Red)

Channel Switch

Band Switch

PRODUCT OVERVIEW:

G3 Wireless Controller uses advance technology which gives you the ability to play without the

limitations of a typical corded controller, hence there are a few switches and LED (lights) not

found on your basic GameCube™ Controller.

Channel Switch (Receiver and Controller):

This switch selects the broadcast channel of the radio frequency. There are four positions;

1, 2, 3 and 4. There is a corresponding Channel Switch on the receiver

Band Switch (Receiver and Controller):

This switch selects the bandwidth. There are two positions; A and B. There is a corresponding

Band Switch on the receiver

Power Switch (Controller):

This switch selects the power mode. There are 3 positions; Off, On, and Rumble Off

Signal LED (Yellow, Receiver and Controller):

When on or flickering data is being transmitted between Controller and Receiver

Power LED (Red, Receiver):

When on indicates Receiver is operating correctly

Link LED (Green, Receiver):

When on indicates Controller and Receiver are linked and communicating. If flickering the

Controller and Receiver are not communicating

INSTRUCTIONS:

1. Insert Batteries:

Remove the battery lid and place the two AA batteries (included) into the G3 Wireless

Controller. Make sure they are inserted as shown in the battery compartment. The batteries

included are not long life.

2. Plug in the Receiver:

With the GameCube™ turned off, plug the receiver into controller port one (far left port.)

3. Check Band setting:

Confirm that the Band Switch is set to A on both the controller and the receiver.

Note:the only time you would ever change this switch is if you experienced a drop off in the

signal, causing game play to be suspended. If this happens repeatedly we suggest

you switch to Band B on both the Controller and Receiver.

4. Select a Channel on the Controller:

You may select any channel you desire 1, 2, 3 or 4.

5. Select a Channel on the Receiver:

This must match the channel selected on the Controller.

Note:If using more then one controller you must use different channel settings, i.e., the first

controller and receiver are set to Channel 1, the second controller and receiver are

set to Channel 2. The channel position selected on the G3 Controller and Receiver

have no relation to the GameCube™ controller ports.

6. Turn on the Controller:

Move the Power Switch to On, the signal LED will light.

Note:If you wish to extend battery life select the Rumble Off position. This will turn off the

rumble effect in game play resulting in a doubling of your battery life.

OTHER FEATURES:

Multiple Players:

You may play with up to four G3 Wireless controllers. Check to see that the channel switches

are set as outlined above.

Power Save Mode:

When not in use the G3 controller automatically goes into a sleep mode to conserve

batteries. A touch of any button puts the controller back into play mode.

Note: Turn off the controller when not in use to extend your battery life.

Turbo Function:

This feature allows rapid fire of any selected fire button. To turn on, press the Turbo button,

and then while still holding down the Turbo button press the fire button that you wish to have

the Turbo feature. To return the button back to a normal fire button repeat the above process

or turn on and off the controller.

For technical questions please visit

http://www.pelicanacc.com

or call us directly at 1-800-331-3844

Gamer’s Guarantee

Changes or modifications not expressly approved by the manufacture could void the

user's authority to operate the equipment. This device complies with Part 15 of the

FCC Rules. Operation is subject to the following two conditions; (1) this device may

not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

G3 Wireless Controller

G3 Wireless Receiver