• Accessories Installation Instructions Mercedes-Benz Bluetooth® Cradle adaptor
Mercedes-Benz Bluetooth® Cradle adaptor
1 M+P-03F-6311
The Mercedes-Benz approved/ recommended Bluetooth® Phones can be utilized inside Mercedes-Benz vehicles without affecting vehicle electronics. Application These installation instructions are valid for vehicles with an MHI hands-free communications systems and a Mercedes-Benz-approved Bluetooth® mobile telephone. An overview of approved mobile telephones can be found on the Internet at www.wireless4mb.com and is available at any Mercedes-Benz Center.
RF Exposure statement: The antenna shown in this filing must not be co-located or operated in conjunction with any other antenna or transmitter. End users may not be provided with the installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. For portable applications OEM integrators need no SAR evaluation. The max source-based time-averaged output of 0.0005 W is below the low threshold of 24mW for d < 1.5 cm.
- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected. - Consult the dealer or an experienced radio/TV technician for help.
Note This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. Installing the MB Bluetooth® Cradle adaptor 2 1 M+P-03F-6312 Insert the MB Bluetooth® Cradle adaptor (1) into the catches on the pre-installed contact plate (2), located in the center console.
- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected. - Consult the dealer or an experienced radio/TV technician for help.
Pairing the mobile telephone with the MB Bluetooth® Cradle adaptor Make sure that the starter switch is in position 1 (see the vehicle Operator’s Manual). 3 M+P-03F-6313 1. With MB Bluetooth® Cradle adaptor connected to vehicle press the button (3) for approx. 2-3 seconds. LED's will begin to flash rapidly. The MB Bluetooth® Cradle adaptor is in Discovery Mode and can be detected by a Bluetooth® mobile telephone. The MB Bluetooth® Cradle adaptor will appear as "MB Phone system" on the mobile telephone.
4 5 M+P-03F-6379 3. To locate the Pass-Key remove cover (4) by sliding it away from the MB Bluetooth® Cradle adaptor. Located behind this cover (4) there will be a sticker containing the Pass-Key (5). 4. Enter the Pass-Key into the mobile telephone. Depending on the type of mobile telephone being used, it may be necessary to confirm a connection request (see the mobile telephone manual). Once the Pass-Key has been entered and accepted the LED's will be lit continuously.
The connection is re-established automatically every time the mobile telephone enters into the MB Bluetooth® Cradle adaptor’s range, as long as the mobile telephone is switched on and the starter switch is in position 1 (see the vehicle Operator’s Manual). Depending on the type of mobile telephone being used, a message may appear in the display (see the mobile telephone manual).
When the starter switch is in position 1 (see the vehicle Operator’s Manual), the MB Bluetooth® Cradle adaptor will search for the last connected mobile telephone and reconnect. The mobile telephone will then be reconnected as soon as it enters the range of the MB Bluetooth® Cradle adaptor. If the last-connected mobile telephone is not detected, the second-to-last connected mobile telephone (and so on) will be searched for sequentially and, if detected by the MB Bluetooth® Cradle adaptor, reconnected.
Connecting the mobile telephone and MB Bluetooth® Cradle adaptor manually Valid for all Mercedes-Benz vehicles with the exception of the model year 2007 S-Class: on the COMAND or • Press button radio. Model year 2007 S-Class vehicles: • See vehicle Operator's Manual. Note Before connecting the mobile telephone and MB Bluetooth® Cradle adaptor manually, the mobile telephone must already be paired with the MB Bluetooth® Cradle adaptor (see page 3).
Disconnecting the Bluetooth®connection automatically The connection between the MB Bluetooth® Cradle adaptor and the mobile telephone is automatically disconnected if the maximum range (30 ft) is exceeded. Depending on the type of mobile telephone being used, it may be necessary to confirm a connection request (see the mobile telephone operating instructions).
Disconnecting the Bluetooth®connection manually The connection between the mobile telephone and the MB Bluetooth® Cradle adaptor can be disconnected at any time (see the mobile telephone manual). Disconnect the paired mobile telephone from MB Bluetooth® Cradle adaptor using COMAND or radio. Valid for all Mercedes-Benz vehicles with the exception of the model year 2007 S-Class: on the • Press and hold button COMAND or radio for approx. 3 seconds.
Detaching the MB Bluetooth® Cradle adaptor 2 6 1 7 M+P-03F-6314 Press and hold the release button (6). Slide the MB Bluetooth® Cradle adaptor (1) in direction of arrow (7) and remove it from the pre-installed contact plate (2). Operating instructions Please refer to your Mercedes-Benz vehicle Owner’s Manual for operating instructions regarding the MHI hands-free communication system cradle.
© 2005, Mercedes-Benz Accessories Inc. Not to be reprinted, translated or otherwise reproduced, either wholly or in part. Mercedes-Benz Accessories Inc.