Bluetooth Handsfree Car Kit BTHFCK-xxx compatible with: • Ericsson 520 • Ericsson T68 • Sony-Ericsson T68i • Nokia 6310, 6310i • Nokia 8910 • Siemens S55 • Philips Fisio 820 C O D E C Noise & Echo Cancellation DSP Voice Recognition Digit Dialing Name Dialing Phonebook Filter Handsfree states Battery Filter & Volt.
BTHFCK User’s Guide Revision: A Page 222 Table of Contents Introduction ...................................................................................................................................................................3 Symbols used in this manual .........................................................................................................................................3 HMI control pad (Human Mashine Interface) ..............................................................
BTHFCK User’s Guide Revision: A Page 333 Introduction Congratulations on your purchase of the high-performance PEIKER Bluetooth Hands-free Car Kit (BTHFCK). When coupled with a Bluetooth-enabled cellular phone, you will enjoy both greater freedom and greater safety as you use your phone from the comfort of your vehicle.
BTHFCK User’s Guide Page 444 Revision: A HMI control pad (Human Mashine Interface) The HMI is your ‘home base’ → it activates initial operation of the system and provides access to all the available features. It’s simple to use but activates some powerful capabilities. The basic functions of the control pad are defined below. EINBETTENEINBETTENEINBETTENFORMATVERBINDENAfter system start by a new occuring ignition signal, the Mute and the power LED are turned on for 2 seconds.
BTHFCK User’s Guide Revision: A Page 555
BTHFCK User’s Guide Revision: A Page 666 Feature overview The PEIKER Bluetooth Car Kit has the following primary capabilities: Receiving a call → by pressing the Hook button or say “yes” Rejecting a call → by pressing the Hook button longer than 3s Digit Dialing → say “dial” and speak a string of digits Redial → redials the last number dialled Call → dials a number stored in the BTHFCK phonebook Phone VR activation → by pressing VR longer than 1,5s the cell phone reacts with
BTHFCK User’s Guide Revision: A Page 777 Selection of the desired language Three different languages are available in the kit (more will follow): English NA Spanish French Canadian more will follow (GB, F; ES, D, NL, I). In order to change to a different language, please follow one of the following procedures.
BTHFCK User’s Guide Revision: A Page 888 Setup and phone registration (Pairing) The first step in using the kit is to ‘register’ your Bluetooth-enabled phone with the car kit. This process, usually called ‘pairing’ or ‘registration’ allows your phone to communicate with the handsfree system and ensures that other phones cannot inadvertently do so.
BTHFCK User’s Guide Revision: A Page 999 After the system becomes active (after ignition is turned on), the system tries to establish a bluetooth connection. Maybe your mobile prompts for a confirmation for this connection. If the connection is opened the power-on LED of the HMI is turned on. Receiving a Call Once your phone has been registered, then the car kit will automatically connect to your phone each time you enter your vehicle and start the ignition.
BTHFCK User’s Guide Revision: A SETUP EMERGENCY TOWING ASSISTANCE Page 111000 To access one of these features, simply speak the desired function name and the kit will respond appropriately. A single BEEP will be heard after most prompts coming from the system. This signifies that the Voice Recognition is now ready to accept input from the user. Â YOU MUST WAIT for the BEEP before SPEAKING a COMMAND or NUMBER.
BTHFCK User’s Guide Revision: A Page 111111 Redial The RE-DIAL command is used to have the kit place a call to the same number that was previously called with mobile. (1) Press EINBETTENHook [ ‘Ready’ BEEP [ Say “Re-Dial” [ ‘Dialling [ the last-dialed number will be called. Call The CALL command is used to dial pre-stored phone numbers from your phonebook. The system is capable of saving over 32 names, each with four different phone numbers.
BTHFCK User’s Guide Revision: A Page 111222 Phonebook The PHONEBOOK command is used to setup and modify all features relating to your phonebook. Specifically it allows you to store new names with up to 4 locations/numbers per name. You can also edit or delete existing entries.
BTHFCK User’s Guide  Revision: A Page 111333 New Entry If you do not provide any response to the various requests throughout the Add New command sequence, typically the particular system prompt will be repeated 3 times followed by a long BEEP and then the system will exit the menu. (1) ‘Phonebook New Entry. Name please BEEP (2) You train a new word in two utterances. Please say the name naturally you wish to train.
BTHFCK User’s Guide  Revision: A Page 111444 List Name If you do not provide any response to the various requests throughout the List Name command sequence, typically the system prompt ‘Yes or No, Cancel or Quit’ will be repeated three times, followed by a long BEEP and the system will return to the PHONEBOOK main prompt. (3) ‘Would you like to List Name with Location? BEEP [ Y-1 or N-1 Y-1 N-1  name.
BTHFCK User’s Guide  Revision: A Page 111555 Delete If you do not provide any response to the various requests throughout the Delete command sequence, typically the particular system prompt will be repeated 3 times followed by a long BEEP and then the system will return to the next level above it in the menu (3) ‘Deleting.
BTHFCK User’s Guide Page 111666 Revision: A SetUp The SETUP command is used to register/pair Bluetooth-enabled phones with the kit and to set other default operational modes.
BTHFCK User’s Guide Page 111777 Revision: A Towing Assistance The TOWING ASSISTANCE command allows you to quickly connect to the Roadside Service number. (1) Press EINBETTENHook [ ‘Ready’ BEEP [ Say “Towing Assistance” [ ‘Dialling Towing Assistance. Is this correct?’ [ “YES” [ Towing Assistance number is dialled [ Exit from VR [ “NO” [ Return to Ready prompt Advanced Features Microphone Mute MUTE During an active phone call, the handsfree microphone can be muted by pressing the button.
BTHFCK User’s Guide Revision: A Page 111888 Call Waiting and Conference Calling If you have a second call coming in while you are already carrying on a conversation, you have the following options: (1) Switch to the Incoming Call While Placing Existing Call on Hold [ press the EINBETTENHook button longer than 1.
BTHFCK User’s Guide Revision: A Page 111999 Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (based on FCC Part 15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
BTHFCK User’s Guide Revision: A Page 222000 Speaker and Microphone Mounting Loudspeaker positioning • Please install the speaker as shown above and use the delivered screws. • It is not recommended to mount it directly next to the microphone, as there would be an echo for the phone partner. If you mount the microphone on the right side of the driver, you could mount the speaker for example on the left side of the driver.