IPR2 5000/7500 IPR2 5000/7500 DSP ™ ™ Power Amplifiers Operating Manual www.peavey.
Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of electrical shock — DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel.
Är avsedd att uppmärksamma användaren på förekomsten av viktiga handhavande- och underhållsinstruktioner (service) i den litteratur som medföljer produkten. OBSERVERA: Risk för elektrisk stöt – ÖPPNA INTE! OBSERVERA: För att minska risken för elektrisk stöt, avlägsna inte höljet. Inga delar inuti kan underhållas av användaren. Låt kvalificerad servicepersonal sköta servicen.
JAPANESE 」人体への電気ショックの危険が考えられる製品筐体内の非絶縁「危険電圧 。の存在をユーザーに警告す るものです 製品に付属している説明書に記載の重要な操作およびメンテナンス 。（サービス）要領の存在をユーザーに警告するものです !注意： 電気ショックの危険あり — 開けないでください 、注意： 電気ショックの危険を低減するため 。カバーを外さないでください 内部部品はユーザーによるサービス不可。資格のあるサービス要因のサービスを要請してくだ 。さい 、警告:電気ショックまたは火災の危険を避けるため 。この装置を雨または湿気にさらしてはなりません 。ま た、過敏など液体を含む物をこの装置上に置いてはなりません 。この装置を使用する前に、警告事項につ いて操作ガイドをお読みください CHINESE 保護接地端子。装置は保護接地に接続している電源コンセントに接続する必要があります 。三角形内带有箭头闪电状符号意在敬告用户，表明产品内部有非绝缘的“危险电压”存在，
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9.
CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6. Limpiar solamente con una tela seca. 7. No bloquear ninguna de las salidas de ventilación. Instalar de acuerdo a las instrucciones del fabricante. 8.
ATTENTION: L’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. Lire ces instructions. 2. Gardez ce manuel pour de futures références. 3. Prétez attention aux messages de précautions de ce manuel. 4. Suivez ces instructions. 5. N’utilisez pas cette unité proche de plans d’eau. 6. N’utilisez qu’un tissu sec pour le nettoyage de votre unité. 7.
SICHERHEITSHINWEISEACHTUNG: Beim Einsatz von Elektrogeräten müssen u.a. grundlegende Vorsichtsmaßnahmen befolgt werden: 1. Lesen Sie sich diese Anweisungen durch. 2. Bewahren Sie diese Anweisungen auf. 3. Beachten Sie alle Warnungen. 4. Befolgen Sie alle Anweisungen. 5. Setzen Sie dieses Gerät nicht in der Nähe von Wasser ein. 6. Reinigen Sie es nur mit einem trockenen Tuch. 7. Blockieren Sie keine der Lüftungsöffnungen. Führen Sie die Installation gemäß den Anweisungen des Herstellers durch.
1. Lue nämä ohjeet. 2. Säilytä nämä ohjeet. 3. Huomioi kaikki varoitukset. 4. Noudata kaikkia ohjeita. 5. Älä käytä laitetta veden lähellä. 6. Puhdista vain kuivalla kankaalla. 7. Älä tuki mitään tuuletusaukkoja. Asenna valmistajan ohjeiden mukaisesti. 8. Älä asenna lämpölähteiden, kuten pattereiden, liesien tai muiden lämpöä tuottavien laitteiden (kuten vahvistinten) lähelle. 9. Älä poista polarisoidun tai maadoitustyyppisen tulpan suojausta.
VARNING: När du använder elektriska produkter ska grundläggande försiktighetsåtgärder iakttas, inklusive följande: 1. Läs dessa instruktioner. 2. Behåll dessa instruktioner. 3. Iakttag alla varningar. 4. Följ alla instruktioner. 5. Använd inte apparaten i närheten av vatten. 6. Rengör endast med en torr trasa. 7. Blockera inte ventilationsöppningarna. Installera i enlighet med tillverkarens instruktioner. 8.
ADVARSEL: Ved bruk av et elektrisk apparat må grunnleggende forsiktighetsregler følges, inklusive de følgende: 1. Les disse instruksjonene. 2. Ta vare på disse instruksjonene. 3. Følg alle advarslene. 4. Følg alle instruksjoner. 5. Ikke bruk apparatet i nærheten av vann. 6. Rengjør bare med en tørr klut. 7. Ikke blokker noen av ventilasjonsåpningene. Installer i henhold til produsentens instruksjoner. 8.
WAARSCHUWING: Bij gebruik van elektrische producten, moeten elementaire voorzorgsmaatregelen altijd worden opgevolgd, waaronder het volgende: 1. Lees deze gebruiksaanwijzing. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. Bewaar deze gebruiksaanwijzing. Besteed aandacht aan alle waarschuwingen. Volg alle instructies op. Gebruik dit apparaat niet in de buurt van water. Reinig het alleen met een droge doek. Blokkeer geen ventilatieopeningen.
ATTENZIONE: Durante uso di apparecchiature elettriche vanno osservate alcune precauzioni basilari, tra cui le seguenti: 1. Leggete queste istruzioni. 2. Conservate le istruzioni. 3. Rispettate tutte le avvertenze. 4. Seguite le istruzioni. 5. Non usate questo prodotto vicino all’acqua. 6. Pulite esclusivamente con un panno asciutto. 7. Non ostruite le fessure di ventilazione. Installate il dispositivo seguendo le istruzioni del produttore. 8.
ADVERTÊNCIA: Ao usar eletrodomésticos, precauções básicas devem sempre ser seguidas, incluindo as seguintes: 1. Leia estas instruções. 2. Mantenha estas instruções. 3. Preste atenção a todas as advertências. 4. Siga todas as instruções. 5. Não use este aparelho perto d’água. 6. Limpe somente com um pano seco. 7. Não obstrua nenhuma das aberturas de ventilação. Instale de acordo com as instruções do fabricante. 8.
警告: 電気製品を使用するときは、次の項目を含め、基本的な注意事項を常にお守りください。 1. 本書の指示内容をお読みください。 2. 本書は保管してください。 3. すべての警告に注意してください。 4. すべての指示に従ってください。 5. 本装置を水の近くで使用しないでください。 6. お手入れには乾いた布をお使いください。 7. 開口部をふさがないでください。 メーカーの指示に従って設置してください。 8. ラジエータ、 ストーブなど (アンプを含む)、発熱体の近くに設置しないでください。 9. 分極プラグや接地プラグの安全性を損なわないようにしてください。分極プラグの2つのブレードは、一方が他より幅広くなっています。 接地式のプラグには2つのブレードと接地プラグがあります。幅広のブレードや接地プラグは安全のために付けられています。所定のプ ラグがコンセントなどに合わない場合、 旧式のコンセントなどの交換について技術者に問い合わせてください。 10.
CHINESE 重要安全事项 警告 ：操作电器产品时，请务必遵守基本安全注意事项，包括 ： 1. 阅读说明书。 2. 妥善保管说明书。 3. 注意所有安全警告。 4. 按照要求和指示操作。 5. 请勿在靠近水（或其它液体）的地方使用本机。 6. 本机只能用干燥布料擦拭。 7. 请勿遮盖任何通散热口。确实依照本说明书安装本机。 8. 请勿将本机安装在任何热源附近，例如电暖器、蓄热器件、火炉或其他发热电器（包括功率放大器）。 9. 请勿破坏两脚型插头或接地型插头的安全装置。两脚型插头有两个不同宽度的插头片，一个窄，另一个宽一点。接地型插头有两个相同 的插头片和一个接地插脚。两脚型插头中宽的插头片和接地型插头接地插脚起着保障安全的作用。如果所附带的插头规格与您的插座不 匹配，请让电工更换插座以保证安全。 10. 请勿踩踏或挤压电源线，尤其是插头、插座、设备电源输入接口或者电源线和机身连接处。 11. 本机只可以使用制造商指定的零件 / 配件。 12.
경고: 전기 제품 사용 시 다음 사항을 포함해 기본적인 주의 사항을 항상 따라야 합니다. 1. 이 지침을 읽어 주십시오. 2. 이 지침을 준수하여 주십시오. 3. 모든 경고 사항에 주의해 주십시오. 4. 모든 지침을 따라 주십시오. 5. 물기가 있는 근처에서 이 기기를 사용하지 마십시오. 6. 마른 헝겊으로만 청소해 주십시오. 7. 통풍구를 막지 마십시오. 제조업체의 지침에 따라 설치해 주십시오. 8. 라디에이터, 가열기, 난로 또는 열을 발산하는 기타 기기(앰프 포함) 근처에 설치하지 마십시오. 9. 극성 플러그나 접지형 플러그의 안전 용도를 무시하지 마십시오. 극성 플러그는 한쪽 날이 다른 쪽보다 더 넓습니다. 접지형 플러그에는 2개의 날과 1개의 접지 플러그가 있습니다. 넓은 날 또는 1개의 접지 플러그는 안전을 위해 제공됩니다. 제공된 플러그가 사용자의 콘센트에 맞지 않으면 구식 콘센트의 교체에 대해 전기 기술자에게 문의하십시오. 10.
ARABIC ﺗﻌﻠﻴﻤﺎﺕ ﺍﻷﻣﺎﻥ ﺍﻟﻤﻬﻤﺔ ﺗﺤﺬﻳﺮ :ﻋﻨﺪ ﺍﺳﺘﺨﺪﺍﻡ ﺍﻟﻤﻨﺘﺠﺎﺕ ﺍﻟﻜﻬﺮﺑﻴﺔ ،ﻳﺠﺐ ﺍﺗﺒﺎﻉ ﺍﻻﺣﺘﻴﺎﻃﺎﺕ ﺍﻷﺳﺎﺳﻴﺔ ﺩﺍﺋﻤﺎ ،ﻭﺍﻟﺘﻲ ﺗﺸﻤﻞ ﺍﻟﺘﺎﻟﻲ: .1 ﻗﺮﺍءﺓ ﻫﺬﻩ ﺍﻟﺘﻌﻠﻴﻤﺎﺕ. .2 ﺍﻟﺤﻔﺎﻅ ﻋﻠﻰ ﻫﺬﻩ ﺍﻟﺘﻌﻠﻴﻤﺎﺕ. .3 ﺍﻻﻧﺘﺒﺎﻩ ﻟﺠﻤﻴﻊ ﺍﻟﺘﺤﺬﻳﺮﺍﺕ. .4 ﺍﺗﺒﺎﻉ ﻫﺬﻩ ﺍﻟﺘﻌﻠﻴﻤﺎﺕ. .5 ﻋﺪﻡ ﺍﺳﺘﺨﺪﺍﻡ ﻫﺬﺍ ﺍﻟﺠﻬﺎﺯ ﻋﻠﻰ ﻣﻘﺮﺑﺔ ﻣﻦ ﺍﻟﻤﺎء. .6 ﻳﻨﻈﻒ ﻓﻘﻂ ﺑﻘﻄﻌﺔ ﻗﻤﺎﺵ ﺟﺎﻓﺔ. .7 ﻻ ﺗﻘﻢ ﺑﺴﺪ ﺃﻱ ﻓﺘﺤﺎﺕ ﺗﻬﻮﻳﺔ .ﻳﺘﻢ ﺍﻟﺘﺜﺒﻴﺖ ﻭﻓﻘﺎ ﻟﺘﻌﻠﻴﻤﺎﺕ ﺍﻟﻤﺼﻨﻊ. .
ed his es or bly ur act his 005 ne ur es la é, ur à 05 a un en ja llä vat EG 05 uct d. de et te en dit 设备 生 成 请 收 the the retailer retailer where where the the product product was was purchased. purchased. They They can can take take this this product productfor forenvironmental environmentalsafe saferecycling. recycling. Logo referenced in Directive 2002/96/EC Annex Logotipo al que se hace referencia en la Directiva 2002/96/EC IV (OJ(L)37/38,13.02.
FCC Compliancy Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, that may cause undesired operation. Warning: Changes or modifications to the equipment not approved by Peavey FCC Statement Electronics Corp. can void Compliancy the user’s authority to use the equipment.
ENGLISH IPR2™ 5000 / 7500 Power Amplifier Congratulations on your purchase of an IPR2™ power amplifier, designed for years of reliable, flawless operation under rigorous use. The groundbreaking IPR series utilizes an advanced design that allows Peavey engineers to dramatically reduce weight while increasing output power, reliability and thermal efficiency.
Front Panel 7 1 8 IPR2™ 7500 6 3 5 4 8 3 2 7 1 8 IPR2™ 5000 1 2 3 4 5 6 7 8 6 3 5 4 8 3 2 aC POWER SWITCH This button triggers the relay that provides power to the amplifier. This unique power switch will glow blue dimly. When turned on, it illuminates brightly. INDICaTORS The IPR2™ amplifiers feature five front-panel LED indicators per channel: ACTIVE, SIGNAL, DDT™, TEMP and DC.
Rear Panel 14 IPR2™ 7500 9 9 11 10 11 9 12 12 13 CHaNNEL MODE SWITCH: HIGH PASS This position is used to activate the HIGH PASS filter for the corresponding channel. This filter will limit the frequencies sent to the associated amplifier channel to frequencies above 100 Hz. In situations where separate subwoofer cabinets are being used, this position would indicate connecting the mid-high frequency speaker cabinet to the channel associated with the HIGH PASS switch.
Rear Panel 14 IPR2™ 5000 9 11 10 11 9 12 12 13 13 CIRCUIT BREaKER In the unlikely event of operating conditions that may potentially damage the amplifier, the circuit breaker may trip. After inspecting the cables and connections, the amplifier can be reset. If the circuit breaker trips a second time, contact the local Peavey authorized service center. 14 aC POWER INLET: This is the receptacle for an IEC line cord, which provides AC power to the unit.
ENGLISH IPR2™ 5000/7500 DSP Power Amplifier As the name implies, the IPR2™ 5000 and 7500 DSP all include advanced digital signal processing. The DSP was designed to be incredibly effective, yet extremely easy to use. Using unique and revolutionary advanced bass enhancement processes, the IPR2 DSP amplifiers dramatically improve the perceived level of bass in any system, using a fraction of the power that would be required with any other power amp.
Front Panel 1 8 2 9 IPR2™ 7500 DSP 1 7 4 2 IPR2™ 5000 DSP 6 5 9 4 3 8 9 7 4 6 5 9 4 3 1 aC POWER SWITCH This button triggers the relay that provides power to the amplifier. This unique power switch will glow blue (along with the Peavey logo) in standby mode, indicating AC power has been connected to the amplifier but the amplifier has not yet been turned on. 2 LCD SCREEN Blue, backlit LCD screen.
Rear Panel 14 IPR2™ 7500 DSP 11 11 12 12 14 IPR2™ 5000 DSP 11 10 13 11 12 12 13 CONNECTING INPUTS Input connections are made via the 3-pin XLR (pin 2+) or 6.3 mm plug combination connectors on the rear panel of the amplifier. The inputs are actively balanced. The input overload point is high enough to accept the maximum output level of virtually any signal source.
Navigation Overview Once the IPR screen appears, you can start adjusting the DSP processor. Pressing the encoder will bring you to the main menu. The encoder knob to the right of the display is used to navigate and control the DSP functions. The Channel A and B controls to the left of the display are also encoders but are dedicated to adjusting input gain for each channel. Turning the encoder knob to the right of the display will allow you to scroll through the Main Menu selections.
To select an item from the Main Menu, rotate the encoder until the cursor marks the selection you want. Press the encoder to navigate to the Sub Menu adjustment screens for that processing function. When you enter a processing function Sub Menu, the cursor will appear in the upper left corner of the screen allowing you to scroll through Sub Menu screens. To edit a parameter, press the encoder to move the cursor to the desired parameter on the screen. Turning the encoder then adjusts that parameter.
Unlike the other function Sub Menus, the input mode does not change until you select “Save and Apply” and return to the Main Menu. Crossover Filters, Band-Pass Filters and Polarity Set: BP Filters Independently When you enter the “XOVER” Sub Menu, you are given three options for how the band-pass filters can be set. When Set “BP Filters Independently” is selected, the Channel A and B highpass and low-pass filters are individually set.
Output Polarity Output Polarity The output polarity can be inverted on either channel. Select Normal or Invert in the polarity screen. If you create a crossover with 12dB per octave filters, the high frequency output would likely need to be inverted to maintain the proper phase relationship at the crossover frequency. Temporarily inverting the polarity of one channel of a multi-way system can also aid in the setting of the delay for driver alignment.
Horn EQ The Horn EQ provides a 6dB per octave high frequency boost that is sometimes required for high frequency horns. The frequency control sets the low frequency corner of the filter. To return to the Main Menu, select Discard and Exit or Save and Exit. Delay Delay can be used to align drivers within a loudspeaker or to delay auxiliary speakers like those installed under a balcony. A short delay can also be used to delay the main speakers to align them with the drums or bass guitar.
Saving Settings In the Memory Operation Sub Menu, select “Save Settings.” Select one of the four preset locations. Edit the name by rotating the cursor to select the character and pressing the encoder to step to the next position. Continue until complete. To keep the same name, press the encoder six times to step through the name edit screen. Once the save location has been selected and you have named the preset, you will be given a yes/no option to complete the save.
IPR2™ 7500 Specification Sheet Rated Watts 2ch x 2 ohms 4750 watts 20ms repetitive burst / 3750 watts 1% THD both channels driven @ 1kHz. Rated Watts 2ch x 4 ohms 2800 watts 20ms repetitive burst / 2450 watts 1% THD / 2020 watts 0.15% THD, both channels driven @ 1kHz. Rated Watts 2ch x 8 ohms 1550 watts 20ms repetitive burst / 1425 watts 1% THD / 1200 watts 0.15% THD, both channels driven @ 1kHz.
IPR2™ 5000 Specification Sheet Rated Watts 2ch x 2 ohms 3230 watts 20ms repetitive burst / 2530 watts 1% THD both channels driven @ 1kHz. Rated Watts 2ch x 4 ohms 1985 watts 20ms repetitive burst / 1700 watts 1% THD / 1470 watts 0.15% THD, both channels driven @ 1kHz. Rated Watts 2ch x 8 ohms 1175 watts 20ms repetitive burst / 1025 watts 1% THD / 880 watts 0.15% THD, both channels driven @ 1kHz.
IPR2 7500 DSP Specification Sheet Rated Watts 2ch x 2 ohms 4750 watts 20ms repetitive burst / 3750 watts 1% THD both channels driven @ 1kHz. Rated Watts 2ch x 4 ohms 2800 watts 20ms repetitive burst / 2450 watts 1% THD / 2020 watts 0.15% THD, both channels driven @ 1kHz. Rated Watts 2ch x 8 ohms 1550 watts 20ms repetitive burst / 1425 watts 1% THD / 1200 watts 0.15% THD, both channels driven @ 1kHz.
IPR2™ 5000 DSP Specification Sheet Rated Watts 2ch x 2 ohms 3230 watts 20ms repetitive burst / 2530 watts 1% THD both channels driven @ 1kHz. Rated Watts 2ch x 4 ohms 1985 watts 20ms repetitive burst / 1700 watts 1% THD / 1470 watts 0.15% THD, both channels driven @ 1kHz. Rated Watts 2ch x 8 ohms 1175 watts 20ms repetitive burst / 1025 watts 1% THD / 880 watts 0.15% THD, both channels driven @ 1kHz.
Notes: 38
Notes: 39
Notes: 40
U.S. CUSTOMER WARRANTY REGISTRATION Optional Product Extended Warranty Registration Give us some information and put your extended warranty into effect! Please take a few minutes to fill out this information/survey sheet to help us get to know and serve you better. To save time, submit your warranty registration online at www.peavey.com/support/warrantyregistration 1. 7.
FROM: 42 Place Postage Here Peavey Electronics Corporation Attn: Warranty Department P.O.
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: 09/15/2010 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.
Features and specifications subject to change without notice. Peavey Electronics Corporation • 5022 Hartley Peavey Drive • Meridian • MS • 39305 (601) 483-5365 • FAX (601) 486-1278 • www.peavey.
