PROCOMM® 2.4 GHz Digital Wireless Transmitters Operating Manual www.peavey.
FCC/ICES Compliancy Statement FCCID: I4S-PCXDBP FCCID: I4S-PCXDHT This device complies with Part 15 of the FCC rules and Industry Canada license‐exempt RSS Standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, that may cause undesired operation. Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de licence.
FCC Radiation Exposure Statement(for Model number: PCX-D HT) This equipment complies with FCC &IC RSS-102 RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 1.5 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
PRO COMM® 2.4 GHz Digital Wireless System PRO COMM Rechargeable Handheld Transmitter PRO COMM Rechargeable Bodypack Transmitter ! WARNING: Contains lithium ion batteries. Lithium ion batteries contain Perchlorate-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate ! WARNING: Lithium Ion batteries may be a fire hazard. Do not expose to open flame or excessive heat.
Controls and Indicators 1. Capsule Module: The anti-roll grille protects detachable microphone capsule and the internal foam prevents breathing, wind and POP noises. 2. Fixed Ring 3. Battery Compartment: Accommodates one 18500 rechargeable battery. 4. Housing: Protects transmitter PCB, battery compartment and battery. 5. Ascertain the power is turn “ON” to see battery status. Normal Battery: LEDs indicates battery meters. Weak Battery: Red LED is lit. Recharge or insert a new recharged battery.
Operating instructions for insertion& removing battery 1. 2. 3. Remove grill in counter clock direction. Press and hold both sides of microphone capsule module and remove gently. Ascertain the battery is inserted according to its correct polarity. A click is heard once correctly inserted and grill can be closed properly. No click is heard and grill cannot be closed properly if battery is inserted with the wrong polarity. NOTE: Transmitter cannot be powered on with a charged battery. a.
Operating Instructions 1. Power On & Off a. Power On: Push the ON/OFF switch to the “ON” location, the battery indicators will light. b. Power Off: Push the ON/OFF switch back, the battery indicators will go out. 2. Battery Status Display a. Red LED indicator is lit when battery is too low. Please recharge or insert a new recharged battery.
and compensate by turning up the amplifier volume to increase the sound level as this can easily cause echo or feedback. In contrast, performers with a ‘’louder’’ sound level should not hold the microphone too close as this can easily result in distortion by causing the amplifier system to be overloaded. 4. Furthermore, a large-diaphragm directional microphone has a very distinct proximity effect. When the microphone is close to the mouth, the bass response is strengthened as the distance gets closer.
12. Battery Charging Contact: Align contacts during charging. (a) Metal objects contact is forbidden. (b) It is forbidden to contact metal objects. (Figure 1) (Positive Wear) (Opposite Wear) Audio Input Operating Instructions 1. Insert the lavalier, headset microphone or instrument cable into the audio input connector before power ON the transmitter. 2. Tighten the connector screw clockwise direction as shown in (Figure 2) for a secured fit (Figure 2) Operating Instructions 1. Power On/Off a.
AF Input Connections (1) 2-Wire Electret condenser microphone Capsule (2) 3-Wire Electret condenser microphone Capsule (3) Dynamic Microphone (4) Electric Guitar (5) Line-in (Impedance 8KΩ ATT. 10dB Battery Removal and Installation 1. Pushing down both snap locks on the sides to open battery compartment cover. Take out the one battery. (Figure 3) 2. Insert one charged 18500 rechargeable battery into the battery compartment according to the correct polarity (- and +) as shown in (Figure 4) .
c. into the charger to re-charge for 10-20 seconds to wake-up the battery. It should work. If charger cannot be used, reverse the battery insertion for 10-20 seconds, wake up the battery with correct polarity. It should work. Method 2: a. Power off the transmitter before open the hinged cover. Press battery protection circuitry reset button once to wake-up battery. Power on the transmitter.
c. The batteries may be faulty or damaged and should be replaced. Rechargeable 18500 Li-ion Battery (Transformer is shown here for reference only) Notes 1. Refer to actual product in the event of product description discrepancy. 2. Frequency range and maximum deviation comply with the regulations of different countries. WARNING 1. FOR OUTDOOR USE: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 2.
www.peavey.com Warranty registration and information for U.S. customers available online at www.peavey.com/warranty or use the QR tag below Features and specifications subject to change without notice. Peavey Electronics Corporation 5022 Hartley Peavey Drive Meridian, MS 39305 Logo referenced in Directive 2002/96/EC Annex IV (OJ(L)37/38,13.02.