DATASHEET INDUSTRIAL IoT DEVICES Industrial IoT Radio Module 2x2, 802.11ac Wave 2 RM-WIFI-AC-2X2-HP-US, RM-WIFI-AC-2X2-HP-EU, RM-WIFI-AC-2X2-HP-CA Bands Technologies Features • 5 GHz: supports • WiFi • High TX output power of 23 dBm per path, 26 dBm total • IEEE 802.11ac compliant, supporting legacy 802.11a and 20/40/80 MHz channels (up to 256-QAM) • • • • 802.11n operating modes 2x2 MU-MIMO with up to 867 Mbps data rate Standard mini-PCI Express 1.
Industrial IoT Radio Module 2x2, 802.11ac Wave 2 The PCTEL RM-WIFI-AC-2X2-HP 802.11ac Wave 2 is a device built in a standard mini-card form factor and a standard mini-PCIe interface featuring true enterprise-class specifications with high TX output power and support for all 802.11ac channel definitions including 80 MHz channels. Low power consumption and a small form factor make this radio module ideal for integration into a wide variety of platforms. > pctel.
SPECIFICATIONS Industrial IoT Radio Module 2x2, 802.11ac Wave 2 Features and Benefits Feature Benefit Small form-factor Ease of integration into a variety of platforms following PCI Express Mini Card mechanical specification 802.11ac Wave 2 • Uses QCA9898 chipset to produce 802.11ac Wave 2 compliant radio module. • Incorporates 2 RF paths for downlink MU-MIMO and operates over all supported channel configurations including 80 MHz channels. • Backward compatible with 802.11n and 802.11a standards.
SPECIFICATIONS Industrial IoT Radio Module 2x2, 802.
COMPLIANCE Industrial IoT Radio Module 2x2, 802.11ac Wave 2 Compliance Safety Figure 1. Compliance Radio Approvals EMI and Susceptibility IEC 62368-1 FCC Part 15.407 FCC Part 15.107, 15.109 UL/CSA 62368-1 EN 301 893 EN 301 489-1, 301 489-17 RSS-210 ICES-003 RSS-247 6.1. Manufacturer’s Federal Communication Commission (FCC) Compliance Statements Model: RM-WIFI-AC-2X2-HP-US FCC ID: NYPRMWIFIAC2X2 Manufacturer: PCTEL, Inc. 471 Brighton Dr.
COMPLIANCE Industrial IoT Radio Module 2x2, 802.11ac Wave 2 6.1.2. FCC Declaration of Conformity Statement These paragraphs must be included in any end-user documentation. This device complies with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. T his device must accept any interference received, including interference that may cause undesired operation.
COMPLIANCE Industrial IoT Radio Module 2x2, 802.11ac Wave 2 3. Note that per FCC Part 15 rules pertaining to unlicensed transmitters, the host device must be equipped with a unique antenna connector. Compliance with 47 CFR 15.203 does not permit the use of standard connectors such as N, BNC, SMA, TNC, etc. 4. The modular transmitter has been tested to the following FCC rules: a. FCC 15.212 b. FCC 15.407 c. KDB 447498 d. CFR 47 Part 1.1310 5.
COMPLIANCE Industrial IoT Radio Module 2x2, 802.11ac Wave 2 6.2.1. Antenna Information The radio transmitter (IC: 26854-RMWIFIAC2X2) was approved by Innovation, Science and Economic Development (ISED) Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
COMPLIANCE Industrial IoT Radio Module 2x2, 802.11ac Wave 2 6.2.3. ISED Canada Radiation Exposure Statement These paragraphs must be included in any end-user documentation. This transmitter/receiver has been evaluated for RF exposure for humans in reference to ANSI C 95.1 (American National Standards Institute) limits. This evaluation was based on RSS-102 Rev 5. To maintain compliance, the minimum separation distance for RM-WIFI-AC-2X2-HP-CA is 7.87 inches (20 cm) from users or general bystanders.
COMPLIANCE Industrial IoT Radio Module 2x2, 802.11ac Wave 2 9. The integrator or host manufacturer must not provide information to the end user regarding the installation or removal of this modular transmitter from the host device in the user’s manual of the end-product. 10. Any end-user manual shall include all required regulatory information/warnings as shown in this manual. 11. Even though the PCTEL RM-WIFI-AC-2X2-HP-CA radio module has been ISED certified, the host product (i.e.
COMPLIANCE Industrial IoT Radio Module 2x2, 802.11ac Wave 2 11. Même si le module radio RM-WIFI-AC-2X2-HP-CA de PCTEL a été certifié ISDE, le produit hôte (à voire le produit intégré du module radio + le dispositif hôte) doit être évalué pour une conformité continue dans cette configuration spécifique. Veuillez contacter PCTEL pour obtenir les outils nécessaires à une telle évaluation. 12.
COMPLIANCE Industrial IoT Radio Module 2x2, 802.11ac Wave 2 6.3.2. Antenna Information This radio transmitter has been approved under RED 2014/53/EU to operate the antenna types listed below with the maximum gain indicated. The usage of different antennas in the final host device may need a new assessment of host conformity to RED 2014/53/EU. Table 3.
COMPLIANCE Industrial IoT Radio Module 2x2, 802.11ac Wave 2 This device is a 5 GHz wideband transmission system (transceiver), intended for use in all EU member states and the UK. Dansk (Danish) Hermed erklærer PCTEL, Inc., at denne 5 GHz modtager overholder de generelle krav og andre retningslinjer af direktiv 2014/53/EU. Deutsch (German) Hiermit erklärt PCTEL, Inc., dass dieser 5-GHz-Transceiver den grundlegenden Anforderungen und anderen relevanten Bestimmungen der Richtlinie 2014/53/EU entspricht.
CONTACT US For more information about this product contact your sales representative or visit > pctel.com/industrial-iot-devices Solving Complex Wireless Challenges PCTEL is a leading global provider of wireless technology solutions, including purpose-built Industrial IoT devices, antenna systems, and test and measurement products. Trusted by our customers for over 25 years, we solve complex wireless challenges to help organizations stay connected, transform, and grow.