R402 User Manual 1. Interface 1.1 LED Light Color Indication Number 1 2 3 4 5 6 Indicator Power WIFI(2.4G) WIFI (5G) WAN/LAN Internet Signal Color Working Status Dark Power off Green,Solid Power on all led Green,Solid(except internet led ,it show pink) External Power supply Booting up the device Green,Solid 2.4G WIFI is enable(No user) Green,Blink- 0.5s 2.4G Users connected to WIFI Dark 2.4G WIFI is disabled Green,Blink- 0.2s 2.
. Using You can place R402 on a desk or other flat surface. Please keep R402 away from overheating. For optimal performance, please place your R402 router in the center of your home (office), in a location that is away from any potential interference source. 2.1 Access internet by Wire inserted into WAN port or LAN port 1) Connect Ethernet cable between your PC/Notebook and one of the four available LAN ports on R402.
★Recommend setting a convenient SSID and a more secure Wi-Fi passwords before using or browsing the other pages of R402. 3. Administrator menu ●Home The main display settings page shows the network status information such as SIM card status, type and quality of the network signal, new messages notification, and so on. ●Wizard To change the LAN configuration, set the APN , and change the WIFI SSID \ password through the wizard function. ●WAN 1.
Choose your Internet Access Type. If you choose 3G/4G SIM card to access the network: On the APN setting page, Key in the “APN”, “Dial Number” and ”Authentication” which are provided by your mobile network operator. WAN Mode If you choose WAN Mode, please select the type of internet connection for your router. DHCP：A dynamic IP address connection that configures the router to automatically obtain IP address from a DHCP server on the ISP’s network.
. SIM Card PIN Lock Open your PIN page to configure your SIM card. If you reboot the device, the log management page will prompt to enter the correct PIN code, to use the SIM card. The PIN / PUK code is supplied with the SIM card provided by your Network carrier, for more info please consult your Network carrier. 6.
2. DHCP DHCP Mode:Server- the R402 DHCP Service is on, theR402 assigns IP addresses and provides subnet mask ,gateway ,and DNS server information to the network .The R402 is the DHCP server for the network None- the R402 DHCP Service is off ,the R402 does not provide any DHCP services .There is already a DHCP server on the network Starting IP Address & Ending IP Address: The IP range obtained through DHCP by LAN host.
-WPA: WPA is a newer and more secure encryption protocol which makes significant improvements over WEP. There are two versions of WPA; the original WPA, and the newer WPA2. - -WPA Mode :Select the desired authentication method from the drop down menu: Auto (WPA or WPA2) - The router will automatically determine the version of WPA to be used based on the client that is connecting to it. WPA2 - Clients will only be able to associate with the router using the WPA2 standard.
3. Mac Filter The MAC filtering option allows you to deny access to wireless clients based on their MAC address. 4. Station List Shows the devices connected to the R402 wireless devices Users connected to 2.4G Wi-Fi are listed in 2.4G list Users connected to 5G Wi-Fi are listed in 5G list ●Security 1. Firewall Firewall configuration: You can Disable or Enable the Firewall function. You can also set the matching packets rule to receive or reject.
3. DMZ Receive all the data from external network interface forwarded to “DMZ IP address” Enable DMZ: If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer. Note: Placing a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort.
4. Firmware Upgrade You can upgrade the firmware of the router here. Make sure the firmware file you want to use is on the local hard drive of the computer. Click Browse to locate a previously downloaded firmware file on your computer. Once the file has been located, click “Start Update” to carry out the firmware upgrade process. 5. Password This page lets you change the configuration interface passwords for the Administrator New Password: Enter the new password for this account.
6. Data and Time You can synchronize the time with the host; you can also select the time zone 7. Language Select your preferred language from the drop-down menu. 8. Upnp Universal Plug and Play (UPnP) supports peer-to-peer Plug and Play functionality for network devices.
9. Reboot Click Reboot to restart the router 10. USSD Unstructured Supplementary Service Data: You can send some specific numbers or symbols to the service provider. FAQ This Appendix provides solutions to some problems that could be seen when install and use the device. Please read the following instruction, it will help you to solve these problems.
Safety Warning Stay away from interference: All the wireless devices could be possibly interfered, and it will affect the performance of the device. Turn off the device in restricted area: Turned off the device in restricted area. Qualified services: Do not disassemble this device yourself. Please contact professionals to repair and install the device. Accessories: Do not touch the device with wet hands, when it is charging. Only use the accessories that are recognized to be compatible to the device.
