FuzzyScan COMBO Module RM3230 User’s Guide
Introduction You can connect to other Bluetooth wireless devices by integrating the RM3230 combo module to your device.
Specification Brand Name Cino Product Name COMBO Module Model Number RM3230 WLAN Standard IEEE 802 Part 11 b/g/n Bluetooth Bluetooth IM 4.0 + HS compliance Antenna Port Support Single Antenna for both WiFi and BT RF Frequency Band Country dependant; Typical 2.4 to 2.497 GHz Data Modulation DSSS(DBPSK/DQPSK/ CCK) DFDM(BPSK/QPSK/16QAM/64QAM) Data Rate (Mbps) DSSS(1/2/5.
Pin Assignment NO. Pin Name Type Description 1 VBAT I Battery supply input (3.4V~4.5V) 2 VBAT I Battery supply input (3.4V~4.
NO.
NO. Pin Name Type Description 43 SD_DAT3 I/O SDIO data 3. This pin has an internal weak pull-up resistor. 44 SD_DAT2 I/O SDIO data 3. This pin has an internal weak pull-up resistor. 45 SR_PMU_VSS I Switching regulator ground & PMU block analog ground 46 EXT_PWM_REQ I Auxiliary PMU control inputs. 47 VIN_LDO I Buck regulator: Battery Voltage Input 48 SR_VLX1 O Core buck regulator: output to inductor and capacitor tank (2.2uH & 4.7uF are required).
Module Installation Manual Material: Description CD_USI PCBA Q’ty:1 Shielding Case Q’ty:1 Picture Description Q’ty:1 Picture
Tools: Description Picture Description Iron Tin wire Fan Picture
Job Description and Notes: Step Picture Description Job Type: Put CD_USI PCBA on board, solder fixed, avoid short circuits. 01 Note: Welding CD_USI PCBA temperature of 3500C ± 100C, not too high or too low. Job Type: The Shielding Case welded on CD_USI PCBA, careful not to short circuit and CD_USI PCBA. Note: 1 Welded shielding case temperature of 3500C ± 100C, not too high or too low. 02 2 Shielding Case not skew or subsidence short circuit.
Finished: Picture Description 1. Welded shielding case temperature of 3500C ± 100C, not too high or too low. 2. Welding CD_USI PCBA temperature of 3500C ± 100C, not too high or too low. 3. Welding CD_USI PCBA requires a clearance and avoid short circuit. 4. Shielding Case not skew or subsidence short circuit.
Regulatory Information The Wi-Fi is designed to be interoperable with any Wi-Fi technology product that is incorporating Direct Sequence Spread Spectrum (DSSS) and OFDM data modulation and complies with the IEEE 802.11b/g/n. Safety The Wi-Fi, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this device, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones.
Warning 802.11b/802.11g/802.11n/BT 警語： 第十二條→ 經型式認證合格之低功率射頻電機，非經許可，公司，商號或使用者均不得擅自 變更頻率，加大功率或變更原設計之特性及功能。 第十四條→低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象 時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工 業、科學及醫療用電波幅射性電機設備之干擾。 802.11a 警語： 無線傳輸設備 (UNII) 在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用。 (4.7.5) 無線資訊傳輸設備忍受合法通信之干擾且不得干擾合法通信；如造成干擾，應立即停用，俟 無干擾之虞，始得繼續使用。 (4.7.6) 無線資訊傳設備的製造廠商應確保頻率穩定性，如依製造廠商使用手冊上所述正常操作，發 射的信號應維持於操作頻帶中。(4.7.7) LP0002 4.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
