User's Manual

ManualsBrandsPaxton Access ManualsElectronicsNet2 Entry - Panel

Page 1

07/19/2012

Ins-30201-US Net2 Entry - Panel

Technical Support

Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST)

1.800.672.7298 supportUS@paxton-access.com

Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/

Paxton

The Net2 Entry panel is a robust door entry panel incorporating both door entry and access control functions. It is

powered using power over Ethernet (PoE) and communicates with the other elements of the system using IPv6,

providing 'plug and play' installation. Each panel is associated with a Net2 Entry control unit which is the interface to

the door hardware.

Description of product

The panel is equipped with a keypad and a proximity token reader. Net2 software is used to administer the access

control functions. A resident can use either the keypad or a token to gain entry. Installers gain access to the menu

options using an engineer code or an engineer token.

1. Speaker

2. Proximity reader

3. Backlit keypad

4. LCD display

5. IR LEDS for night time operation

6. Microphone

7. Color camera

8. Light sensor

6 7

Summary of content (8 pages)

PAGE 1
07/19/2012 Paxton Ins-30201-US Net2 Entry - Panel Technical Support 1.800.672.7298 Technical help is available: supportUS@paxton-access.com Monday - Friday from 02:00 AM - 8:00 PM (EST) Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/ Description of product The Net2 Entry panel is a robust door entry panel incorporating both door entry and access control functions.
PAGE 2
Installation The best height to install the panel is with the camera at eye level This will allow you to see your visitor's face clearly even when they are wearing a hood or cap. To achieve the best camera performance, try to mount the panel facing away from direct sun or a bright light source. This will also help the user to read the LCD display. Decide how the units are to be connected. You can either run your own wired network or (with the owner's permission) share the buildings existing data network.
PAGE 3
SURFACE MOUNT 1. Determine and mark the height and position for the camera. 2. Mark and drill the hole for the network cable (network patch or Cat5). Ensure that the waterproof grommet will have clearance behind the backbox. 3. Determine the position of the mounting screws, drill the holes and push in the No 8 wall plugs. 4. 5. 6. 7. 8. 9. Pass the cable through the backbox and secure with the grommet. (A loose grommet is supplied for Cat5 cable) Secure the backbox to the wall with the screws provided.
PAGE 4
Use the up and down arrows on the panel to view all the menu options. Use the X key to Cancel Initialising a new system The first time the system is powered up the panel will request that the Engineer code is set up. Enter the required code and press the bell key. Confirm the code and press bell to complete the process. The Net2 Entry system uses a separate control unit to operate the door. To associate a panel with its control unit, the Serial Number of the control unit must be entered.
PAGE 5
Use the up and down arrows on the panel to view all the menu options. 1. Door open time Use the X key to Cancel from the Engineer menu - Press key 1. This is the time period that the lock will stay released once the open door button has been pressed on a monitor. This value may only be changed when not administered by Net2. 2. Volume settings 1. Set voice volume from the Engineer menu - Press key 2 from Volume settings menu - Press key 1 This sets the volume of the entry panel speaker.
PAGE 6
5. Panel settings 1. Set Interface ID from the Engineer menu - Press key 5 from Panel settings menu - Press key 1 This sets the control unit that the Net2 Entry panel is associated with. Enter the Serial Number of the control unit and then press Bell. 2. Factory reset from Panel settings menu - Press key 2 This returns the Entry panel to Factory settings Press 1. Yes Press 2. No 3. Backlight from Panel settings menu - Press key 3 This sets when the Entry panel backlight will be on. Press 1.
PAGE 7
. Engineer Access 1. Set Engineer Code from the Engineer menu - Press key 7 from Engineer Access menu - Press key 1 This allows the Engineer to change the Engineer code 2. Change Engineer Token from Engineer Access menu - Press key 2 This allows the engineer to add / change the Engineer token The engineer can create a token that can be presented to the proximity reader instead of using the engineer code to gain access to the Engineer Menu. 8.
PAGE 8
Specifications Dimensions Electrical Width Height Depth 4 inch 11 inch 1 1/4 inch Min Max Power over Ethernet (POE) power rating 12.95W IEEE 802.