X3s Wireless Data Terminal PAX Computer Technology(Shenzhen)Co., Ltd.
Contents Checklist Please check the components after unpacking. If any one of them is missing, or if there is a page missing from the product manual, etc., please contact the dealer. X3s wireless data terminal 1 pcs Adapter 1 pcs Data line 1 pcs Lithium battery 1 pcs Wrist strap (suite) 1 pcs Unscrew piece 1 pcs Product manual 1 pcs Base (optional) 1 pcs Product Description Installation 1.
and then take the cover off the terminal. As figure shown below. Figure 1-1-1 2) To lock the rear cover: Put back the rear cover and make the 4 screws aligned with the 4 holes, then tighten the screws to lock the cover. As the figure shown below. Figure 1-1-2 2. Install and Remove the Battery 1) To install battery: Put battery into the battery storehouse in the right direction as shown below.
2) To remove battery: Place your finger in the position shown below and slightly dig out the battery. Figure 1-2-2 3. Install SIM Card/PSAM Card /TF Card 1) Install SIM card/PSAM card /TF card in the direction shown below. Figure 1-3-1 2) Remove SIM card/PSAM card /TF card in the direction shown below.
4 Device Charging The device can be charged in two ways: Using Type-C port or base Pogo Pin 1) By Type-C port: Insert the USB cable into Type-C port for charging as shown in the following figure. Figure 1-4-1 2) By base Pogo Pin: Connect the Pogo Pin at the bottom of the terminal with the Pogo Pin of the base for charging.
Instructions 1. Use of Two-dimensional Scanner (One-dimensional Optional) The scanner is on the top of the device.
reading distance is 0-4cm. You can use it by following steps: 1) When running the contactless card reading and writing program, the contactless card function, which is closed by default, will be opened automatically. 2) Enter the “Menu” >”DEMO”> select the type (14443A/B or 15693) according to the label protocol. When placing the card near the battery cover of the device, the selected contactless card can be read correctly.
4) If the surface of screen is dirty, please use soft cloth to clean the screen with diluent screen cleanser. 5) Discard the used polymer battery according to regulations. Do not throw the terminal into fire. Otherwise there is a risk of explosion. 6) Before connecting the power supply to the AC socket, check whether the power supply of the socket is in accordance with the device specified operating voltage. 7) Please contact the special maintenance personnel when the device fails.
Icon shows Do not throw away, need professional recycling. FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.
Cetappareilestconforme aux limitesd'exposition DAS incontrôlée pour la populationgénérale de la norme CNR-102 science de l’innovation et le développementéconomiqueCanadaet a ététestéenconformitéaveclesméthodes de mesure et procéduresspécifiéesdans IEEE 1528 et IEC 62209.Cetappareil et saousesantennes ne doivent pas êtreco-localisésoufonctionnerenconjonction avec tout autreantenneoutransmetteur. The device is going on be operated in 5150~5250 frequency range.