SK800 Smart Kiosk Note: Product images shown may be different than actual product received PAX TECHNOLOGY LIMITED
1、ContentsChecklist Please check the components after unpacking. If any are missing, please contact the dealer.
Interface Diagram 3、Operating Instruction · Power on: Plug in the AC power cable and turn on the power button. · Contactless module indicator: Light indication when using the Contactless module. · LED working indicator: Light indication when the device is working at night. · Card Readers: Magnetic stripe card: Insert magnetic stripe card into card slot and push to the end with magnetic stripe facing down, then pull out the card at a constant speed to swipe card.
Micro SD card slot(Support maximum of 128GB) x 1 Peripheral Ports: RJ45 (LAN) x1 RS232 (DB9)x1 RS485 Half-duplex (RJ-11) x1 HDMIPort(1.4)x1 Power Port x1 Micro USB x1 Card Readers: 2-in-1 magnetic stripe card / IC card reader; Contactless card reader Magnetic Stripe Card Reader: Complied to the standards of ISO7811 and ISO7812 IC Card Reader:Complied to the standards of ISO7816, EMV2000 L1&L2, PBOC3.
4. Pull out the end of the paper so that itextends past the cutting blade, Make surethe paper roll is placed in the direction asshown in the figure below. 5.Close the printer cover, and pull outthe key. Printer will automatically cut offthe extra paper, the paper is changed successfully.
、Install introduction No. 1 2 3 4 Installation List Part SK800Kiosk Wall Bracket M6-50 Expansion Screw M4-12 Combination Screw Picture Qty/pcs 1 1 6 2 Installation Steps 1. Use 6pcs expansion screws to fix the bracket on the wall. • Use an 8.0 mm diameter drill bit to drill holes in the wall according to the position of the bracket fixing hole. The size is shown in the figurebelow: • Note: Hole diameter is 8.0mm, Hole depth is above 60.0mm.
2.Use the 4pcs hooks on the back of the device to hang the whole device on the wall bracket. 3. Use 2pcs M4-12 combination 3screws to attach the machine to the wall bracket at the bottom of the machine.
4. The device installation is completed. 7、Installation and Usage Tips 1) There is no built-in battery, and the device can only be powered by the power adapter. 2) Avoid exposing the device in overheated, humid, dusty, or strong electromagnetic environment. 3) Do not vibrate, shake, or drop the device. 4) Do not insert or unplug any part of the device while it is powered on. Otherwise, it may cause damage to the internal circuit.
Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
cm de distance entre la source de rayonnement et votre corps. The device for operation in the band 5150-5250 MHz is only for indoor use. les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur. Icon shows This symbol on power switch indicates "ON" (power) This symbol on power switch indicates "OFF" (power) This symbol indicates AC voltage This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE).
PAX TECHNOLOGY LIMITED reserves the right to change product technology specifications without notifying. PAX TECHNOLOGY LIMITED Manufacturer: PAX Computer Technology (Shenzhen) Co.,Ltd. Address:4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C. Tel: 0755-86169630 Fax: 0755-86169634 Website: http://www.pax.com.cn Responsible Party: PAX Technology, Inc.