User's Manual
Table Of Contents
- 1)Magnetic Stripe Card
- Put magnetic stripe side of magnetic card towards device interior, swipe the card with a steady speed during through magnetic reader slot. (Support bi-directional swiping)
- 2)IC Card
- Put IC card chip side upward, push-in IC card slot and to bottom.
- Put the contactless card into the sensing areaat the top of LCD
- 2. Installation and Usage Tips
- 1)Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment.
- 2)Forbid non-professional to repair the terminal.
- 3)Before insert the card, please check internal and around of IC card slot. when you foundsome suspicious objects , must reportto related administrator.
- It is highly recommended to enter password as following ways:
- 1)Set up peep shields.Enter password with shield by the structures of cashierdesk;
- 2)Place the POS terminal at an appropriate angle and make sure it is difficult to peer the password. For example, the POSwas installed above the movable bracket.
- 3)In enter password perspective, avoid surrounding video surveillance;
- 4)Pastetext instructions to remind the customers to shelter with body or palm when enter password.
- 5)Merchants can also choose other ways to protect the customer input password.
- The devicesupports 1/2/5.5/11/6/9/12/18/24/36/48/54 Mbps for WIFI2.4GHz b/g
- and MCS0~MCS7 for WIFI n-20MHz of transmitting speed and operating frequency is 2412MHz~2462MHz with 11 channels.The device of RF carrier is DSSS (DBPSK / DQPSK / CCK) and OFDM (BPSK / QPSK / 16QAM / 64QAM)
- Bluetooth, frequency: 2402-2480MHz, transmitting power: 9.0dBm
- WIFI, frequency: 2412-2462MHz, transmitting power: 15.0dBm
- The CLRC663is a highly integrated transceiver IC for contact|ess communication at 13.56MHz.This transceiverIC utillzes an outstanding moduation and demodulation conoept completely integrated for different kinds of contactless comFnunication methodsand...
- The CLRC663 suppors MIFARE1K,MIFARE4K,MIFARE UlraIight,MIFARE UltaIoht C,MlFARE PLUS and MIFARE DESFire products.The CLRC663 supports contactless con1munication and uses the MlFARE highertransfer speeds of up to 848 kbiVs in both directions.
- 4. Icon shows
- Do not throw away, need professional recycling.
- Class II Equipment
- For indoor use only
- Energy Efficiency Marking
- The MAINS plug is used as the disconnected device.
- FCC Regulations:
- Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la s...
Q30 POS Terminal Instruction Manual
Contents Checklist
Please check the components after unpacking. If any one of them is missing, or if thereis a page
missing from the product manual,ect.,please contact the dealer.
Q30 POS Terminal
1
Adapter cable 1
Product Manual 1
1.Instructions
Q30 POSterminals that include a default communication module come standard with one
Ethernet port and RS232, USB.However, if the default communication module is replaced with an
optional communication module. You can chose these additional network capabilities, such as wifi,
BT and Wireless module. In order to correct using, you should refer to following instructions.
1)Magnetic Stripe Card
Put magnetic stripe side of magnetic card towards device interior, swipe the card with a steady
speed during through magnetic reader slot. (Support bi-directional swiping)
2)IC Card
Put IC card chip side upward, push-in IC card slot and to bottom.
3)Tap contactless card (optional).
Put the contactless card into the sensing areaat the top of LCD
4)SAM/SIM Card
① RemovetheSAM/SIM card cover (At the bottom of the terminal).
②Insert the SAM/SIM card tothe correspondingcard slot.
2. Installation and Usage Tips
1)Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment.
2)Forbid non-professional to repair the terminal.
3)Before insert the card, please check internal and around of IC card slot. when you foundsome
suspicious objects , must reportto related administrator.
3. Password Entering Tips:
It is highly recommended to enter password as following ways:
1)Set up peep shields.Enter password with shield by the structures of cashierdesk;
2)Place the POS terminal at an appropriate angle and make sure it is difficult to peer the password.
For example, the POSwas installed above the movable bracket.
3)In enter password perspective, avoid surrounding video surveillance;
4)Pastetext instructions to remind the customers to shelter with body or palm when enter
password.
5)Merchants can also choose other ways to protect the customer input password.