User's Manual

ManualsBrandsPAX Technology ManualsElectronicsPX Communication Module

User Manual

1. Introduction

AMPAK Technology would like to announce a low-cost and low-power

consumption module which has all of the WiFi and Bluetooth functionalities.

The highly integrated module makes the possibilities of web browsing, VoIP,

Bluetooth headsets functional applications and other applications.

With seamless roaming capabilities and advanced security, also could

interact with different vendors’ 802.11b/g/n Access Points in the wireless LAN.

The wireless module complies with IEEE 802.11 b/g/n standard and it can

achieve up to a speed of 72.2Mbps with single stream in 802.11n draft,

54Mbps as specified in IEEE 802.11g, or 11Mbps for IEEE 802.11b to connect

to the wireless LAN. The integrated module provides SDIO interface for WiFi

and UART / I2S / PCM interface for Bluetooth.

This compact module is a total solution for a combination of WiFi + BT

technologies. The module is specifically developed for Smart phones and

Portable devices

2. Features

802.11b/g/n single-band radio

Bluetooth V4.0(HS) with integrated Class 1.5 PA and Low Energy (BLE)

support

Concurrent Bluetooth, and WLAN operation

Simultaneous BT/WLAN receive with single antenna

WLAN host interface options:

- SDIO v2.0 — up to 50 MHz clock rate

BT host digital interface:

- UART (up to 4 Mbps)

Summary of content (6 pages)

PAGE 1
User Manual 1. Introduction AMPAK Technology would like to announce a low-cost and low-power consumption module which has all of the WiFi and Bluetooth functionalities. The highly integrated module makes the possibilities of web browsing, VoIP, Bluetooth headsets functional applications and other applications. With seamless roaming capabilities and advanced security, also could interact with different vendors’ 802.11b/g/n Access Points in the wireless LAN. The wireless module complies with IEEE 802.
PAGE 2
IEEE Co-existence technologies are integrated die solution ECI — enhanced coexistence support, ability to coordinate BT SCO transmissions around WLAN receives 3. PCB Layout 4. Deliverables The following products and software will be part of the product.
PAGE 3
Evaluation Kits Software utility for integration, performance test. Product Datasheet. Agency certified pre-tested report with the adapter board. 5. General Specification 5.1 General Specification Product Description: Support WiFi/Bluetooth Dimension : L x W x H: 12 x 12 x 1.5 (typical) mm WiFi Interface : SDIOV2.0 BT Interface : UART / PCM Operating temperature : -30°C to 85°C Storage temperature : -40°C to 85°C Humidity : Operating Humidity 10% to 95% Non-Condensing 5.2 Voltages 5.2.
PAGE 4
exposure limits set forth for an population/uncontrolled environment can be satisfied. The antenna is integrated into module, and the antenna type is monopole with antenna gain: 1.2 dBi. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated.
PAGE 5
-Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
PAGE 6
Cet appareil est conforme aux limites d'exposition aux rayonnements de la CNR-102 définies pour un environnement non contrôlé. Afin d'éviter la possibilité de dépasser les limites d'exposition aux fréquences radio de la CNR-102, la proximité humaine à l'antenne ne doit pas être inférieure à 20 cm (8 pouces) pendant le fonctionnement normal.