User guide

C95100113
4232-A
【Front side】【Rear side】
BK
Outside contact Outside contact
BK-24 Max 20A/ 5ms
BK-100 None
6mA
←
12V
(15V)
Each CH
No-voltage contact circuit
■Wiring example
( ) : BK-24
COM
BK
6mA
←
12V
(15V)
Each CH
NPN open collector circuit
Current capacity
Table2.Inrush current and Fuse
Table1.CH circuit
Table3.Contact capacity of CH
Apply a voltage displayed below
‘POWER SUPPLY’.And, in case of
Type BK-24, connect - terminal of
power supply to 0V
Power supply
Fuse
See Table2
T-06B0152
T-0710139
T-0710140
Withstand voltage
Leakage current
ON voltage(Vsat)
10mA or higher
DC20V or higher
0.1mA or lower
1V or lower
( ) : BK-24
COM
BK - 24 A P - J
Model Inrush current Fuse
125V 1A
125V 0.5A
250V 0.5A
BK-220 None
(b)
(c)
(a)
□110 mm
+1.0
-0
(148mm)
COM
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
Wiring when NPN
transistor is used
Waterproofing rubber for
the slot
Card slot
Front cover
Terminal screw
M3X6
Case
Apply a voltage for the signal line.Failure
to do so may be damaged to the product.
We thank you for purchasing PATLITE Audible Alarm. Before you start using the product,
please read this instruction manual carefully to use the product correctly. Please store this
document in a safe place. Be sure to read this document again when you are about to
perform tasks such as maintenance and repair.
And if you have any questions, contact a branch office or the technical support printed on
the last page.
Instruction Manual
Audible Alarm
TYPE : BK
The precautions which must be observed to prevent damage to the person using the
product, to people around it, or to property are described in a manner shown below
■The seriousness of injury or damage caused by ignoring the indication and using the
product in a wrong way is categorized with the indications below and descriptions are
added to each of them
Warning
The sections with this indication contain "items which could
cause death or serious injury" if ignored.
The sections with this indication contain "items which could
cause injury or property damage only" if ignored.
Caution
Safety Precautions
●Be sure to turn the power off before wiring or installing the product. Failure to do
so may cause electric shock.
●Do not disassemble or modify the product.There is a risk of fire,electrical shock
etc.For repair, check etc of inside the product, please inquire to each sales office
or technical consultation service written in the last page.
●Take care to perform wiring correctly. If the wiring in incorrect, internal circuit may
be damaged by fire, and it may also be a cause of fire.
●As for the power source, be sure to use this product within the allowable range
of voltage. Failure to do so may be a cause of fire or damage to the product.
●Be sure to let specialists perform installation task which requires construction work.
Failure to do so may cause electric shock, fire, or falling.
●To protect power source circuit and internal circuit of the product,
be sure to install external fuse.
Failures caused by using the product in ways not observing the Warnings and Cautions,
by disassembling or converting the product, or by natural disaster are not covered under
warranty. And do not use the product in ways other than the ways described in this
document.
●Use the product in an environment where there is no electromagnetic or inductive
noise. Speakers are known to generate noise.
●Use the product in an environment where there is no corrosive gas.
Failure to do so may cause malfunction.
●Before you start working on the product, discharge static electricity
from your body. By touching another grounded metal part with bare hand,
the static electricity can be discharged.
●Perform fitting of each part at a recommended torque value.
●Pay attention not to lose the parts such as the front cover, Terminal cover etc.
which are to be detached at performing work.
●When the product is used for security purposes in which safety is emphasized,
be sure to perform daily maintenance, and design a system which is capable
of tackling the occurrence of unlikely event such as malfunctioning or failure.
●Do not use it at the place where vibration exists that is exceeding
the specification.There is a risk of damage and/or falling of the main body.
●Do not use the product as fire alarm.
1. Cautions Which Must Be Observed for Safety Use
2. Model Indicating Format
■Normal-rated voltage
24 : 12-24V DC
100：100Ｖ AC
220：220V AC
■Sound Chart type
A：Type A
C：Type C
D：Type D
E：Type E
■Connectable
Transistor
None：NPN type
P：PNP type
(*P is custom made)
■Body color
J : Light gray
K : Dark gray
Warning
Caution
Other Precautions
Mounting screw for front
cover (M3X6)
Sound group
Selection switch
Terminal cover
SD card
(Model: SDV-128P Sold separately)
* PATLITE Corporation is a member of
the SD Card Association
Mounting hardware
(attachments)
4. How to Install
Mounting surface
(board thickness: 1mm - 10mm)
Before wiring the product, remove the terminal cover. And after the completion of the wiring
attach the terminal cover.
●For the external contact of CH, use no-voltage contact circuit such as relay switch
or open collector circuit (NPN type). As for the contact capacity, see the table 1 to 3.
●The terminal screws should be fastened with the recommended fastening
torque (0.3N・m).
5. How to Perform Wiring
●Before switching on the power supply, confirm that the wiring is correctly performed.
●For countermeasure of noise, it is recommended to perform wiring as short as possible, and to use
shielded wires. In addition, if a signal line is passing along high voltage cables or its wiring is located
at the place likely to receive induction noise, there is a risk of malfunction by the effort of noise.
●If a no-voltage contact such as a relay or a switch etc. is used for power supply line, select the
contact for which rush current is considered.If capacity is insufficient, it will become a cause of
welding(deposition) of the contact and/or malfunction.
●The use of M3 ring terminals with insulating coating is recommended for the wiring of terminal block
to prevent disconnection of wires.
●Be sure to turn the power off before you start wiring. Failure to do so may cause electric shock.
●Be careful not to make a mistake in wiring. Failure to do so may cause damage to the internal
circuit by fire, and it may cause fire.
●To protect the power source circuit and the internal circuit of the product, be sure to install an
external fuse.
●The terminal screws should be fastened with the recommended fastening torque (0.3N・m).
Failure to do so may cause short circuit due to disconnection of wire, and damage to the product.
Warning
Other Precautions
Caution
6-1 Opening and Closing the Front Cover
Open or close the front cover according to the procedure shown below
when performing tasks such as adjusting the volume of the sound or selecting
the sound group.
① Remove the mounting screw (M3X6) for the front cover.
② Push the lower front cover section (part A in the figure on the right)
lightly with finger to slide it downward.
③ When a SD card is to be used, remove the waterproofing rubber
for the slot.
④ After completing tasks, attach the parts removed in the procedure
from ① to ③ in the opposite order.
(Recommended fastening torque for the mounting screw: 0.3N・m)
6. How to Use the Product
Waterproofing
rubber for the slot
Volume control
Mounting screw
for front cover
(M3X6)
Front cover
Card slot
Sound group
selection switch
●Make sure that there is no misalignment with the sound group
selection switch when selecting.
If there is misalignment as shown in the figure on the right, the
sound group selected may not play.
6-2. Selecting a Sound Group
Use the sound group selection switch to select a group from the 16
types from A to P. Use a flat-blade screwdriver with the blade thickness
of 1.0mm or thinner for turning the switch. (Factory default setting:
Sound group A)
●Sound group A to H
By bit input, a sound is played which corresponds to each Sound Group.Regarding the operation,
refer to “6-5-1.Bit input”. In addition, Sounds can be freely combined by utilizing a SD card
in the case of the group H.Refer to “6-3.How to Combine Sounds”.
●Sound group I to O
A sound “5.Rapid Hi-Lo” is played.So, use it for confirming operation and at sound volume adjustment.
●Sound group P
By binary input, a sound is played which corresponds to Sound list.Regarding the operation,
refer to “6-5-2.Binary input”.
1mm
●Attach the waterproofing rubber for the slot securely. Failure to do so may weaken
the product's resistance to water and dust.
●Fasten the mounting screw for front cover with the recommended fastening torque.
In places where vibrations occur, the front cover may fall or the product may be damaged.
Other Precautions
Other Precautions
●The vibration sound may occur when a mounting surface resonates depending on
the material, thickness of a mounting surface or the volume of products.
Information
Author 13:BEETHOVEN VAN LUDWIG 14:BADARZEWSKA BARANOWSKA TEKLA 15:BACH JOHANN SEBASTIAN
16:SCOTT LADY JOHN DOUGLAS 17･18･21･25･28･29:TRADITIONAL 19･27:PD
20:FOSTER STEPHEN COLLINS 22:Song authorized by the Ministry of Education
23:WERNER HEINRICH (DE 2) 24:STEWART JOHN C 26 :MOZART WOLFGANG AMADEUS 30:BLANTER MATVEJ ISAAKOVICH
31:WORK HENRY CLAY 32:SCHUBERT FRANZ
Author 13:CREWE BOB 14:CARPENTER RICHARD LYNN 15:JOPLIN SCOTT 16:CARRELL JAMES P
17:
Kouichi Sugiyama 18:WILSHAW MICHAEL 19:PACHELBEL JOHANN 20:Ijichi Hiromasa
21:Hiroshi Miyagawa 22:Takeo Watanabe 23,30:Tetsuro Oda 24:CONTI BILL 25:WARREN DIANE EVE
26: Yuka Kawamura 27:KAN 28: Masahiro Andoh 29: Totasu Matsumoto 31: Tatsuya Hirakawa
32: Yumi Matsutoya
Sound groups
●Sound Chart type A (BK-□A)
Sound List
Sound groups
●Sound Chart type C (BK-□C)
Sound List
Author 11:New Funky Sueyoshi 12･17:Yumi Matsutoya 13:Ami Ozaki 14:Tetsuji Hayashi 15:Tatsuro Yamashita
16:Kazumasa Oda 18:Maria Takeuchi 19:HILL MILDRED J 20:CHURCHILL FRANK E
21･22･27･29･30･31･32:TRADITIONAL 23:
Nobuyoshi Koshibe 24: Takeshi Shibuya 25:SCHUBERT FRANZ
26:MARKS JOHN D 28:
American folk song
Sound groups
●Sound Chart type D (BK-□D)
Sound List
CH 4
CH 3
Silent Lakeside
Grandfathers ClockYelp (rapid siren)Daydream Believer
Rapid Hi-Lo Rapid Hi-Lo
CH 6
CH 5
Ｈ
Mary had a little Lamb
Beep (slow intermittent horn)
The camptown Races
CH 2
Stutter (rapid intermittent horn)
Symphony No.40
CH 8
CH 7
CH 3
CH 4
CH 1
CH 8
CH 5
CH 6
CH 2
ＤＣＢＡＥ
CH 7
Holdiridia
Chime
Daydream Believer
Ave Maria
Mary had a little Lamb
The camptown Races
Cuckoo
Blacksmith in the village
Silent Lakeside Daydream Believer Minuet
Amaryllis Grandfathers Clock Romance De Amour
Symphony No.40 Ave Maria
The camptown Races
Call sign
Mountain musician
London bridge is falling down
Romance De Amour
Bell (clear highpitched bell)
Chime Synthesized PianoChime
On the Avignon bridge
Ｉ∼O P
Stutter + Bell
Petrouchka Yelp (rapid siren) Synthesized Melody
Synthesized Piano
Call sign Synthesized Bell Synthesized Bell
London bridge is falling down
The sound 5."Rapid
Hi-Lo"
32 sounds of the
Sound 01∼32 are
playable by using
CH
1∼CH 6.
(Binary input)
Mary had a little Lamb
Petrouchka
Mountain musicianSynthesized Bell
Synthesized Piano
Melody Chime
Cuckoo
CH 1
Group
Holdiridia
Bell (clear highpitched bell)
Group
Melody Chime
Synthesized Piano
Call sign
Minuet
Annie Laurie
London bridge is falling down
Maiden's Prayer
Fur Elise
ＦＧ
Synthesized Bell
ＦＧ
Call sign
Group
Synthesized Bell
Chime
Call sign
The Entertainer
Amazing Grace
Amairono Kamino Otome
Top of the World
Can't Take My Eyes off of You
TruthCall sign
Chime
Yozorano Mukou
Uchuusenkan Yamato
CH 1
Group
Stutter + Bell Truth
Amairono Kamino Otome
The sound 5."Rapid
Hi-Lo"
32 sounds of the
Sound 01∼32 are
playable by using
CH
1∼CH 6.
(Binary input)
Les Champs-Elysees
Odoru Ponpokorin
Ｉ∼O P
Canon
Odoru Ponpokorin
Gonna Fly Now(Theme for "Rocky")
Haruyo Koi
Chime
Call sign Call sign Call signCall sign
Truth Rara Sanshain
Gattsudaze
Can't Take My Eyes off of You
Chime ChimeChime
Makenaide
I Don't Want to Miss a Thing
Imasugu Kisu Mi Amairono Kamino Otome
Yozorano Mukou Haruyo Koi
Makenaide
Aiwa Katsu
Uchuusenkan Yamato
Gattsudaze
Canon
Rara Sanshain
Uchuusenkan Yamato
Oshiete Top of the World
CH 7
Les Champs-Elysees
Chime
Gonna Fly Now(Theme for "Rocky")
ＡＥＤＣＢ
CH 1
CH 8
CH 5
CH 6
CH 2
CH 8
CH 7
CH 3
CH 4
Ｈ
Beep (slow intermittent horn)
Odoru Ponpokorin Rara Sanshain
CH 2
Aiwa Katsu
Stutter (rapid intermittent horn)
CH 4
CH 3
Aiwa Katsu
Imasugu Kisu MiLes Champs-ElyseesSynthesized Melody
Synthesized Piano Amazing Grace
CH 6
CH 5
She Wore a Yellow Ribbon
When the Saints Go Marching In
Yankee DoodleIro Howaitoburendo
Rapid Hi-Lo Synthesized Piano
Ｈ
Saafu Tengoku Sukii Tengoku
Doyoubino Koibito Hi Ho
CH 2
I've been working on the Railroad
Konnako Irukana
CH 8
CH 7
CH 3
CH 4
CH 4
CH 3
CH 6
CH 5
CH 1
CH 8
CH 5
CH 6
CH 2
ＤＣＢＡＥ
CH 7
Akino Kehai
Saafu Tengoku Sukii Tengoku
Konnako Irukana
Hi Ho
Happy Birthday
Hi Ho
I've been working on the Railroad
Bear Song
Yellow Rose of Texas
When the Saints Go Marching In
Wiegenlied
She Wore a Yellow Ribbon
Yellow Rose of Texas
Runner
Oh My Darling Clementine
Yankee Doodle Iro Howaitoburendo
Rudolph the Red-nosed Reindeer
Yankee Doodle Londonderry Air
When the Saints Go Marching In
Beep (slow intermittent horn)
Runner ChimeWiegenlied
Toys Go Cha Cha Cha
Ｉ∼O P
Bell (clear highpitched bell)
Londonderry Air
Stutter (rapid intermittent horn)
Yelp (rapid siren)
Chime
Mamotte Agetai Call sign Call sign
Saafu Tengoku Sukii Tengoku
The sound 5."Rapid
Hi-Lo"
32 sounds of the
Sound 01∼32 are
playable by using
CH
1∼CH 6.
(Binary input)
Iro Howaitoburendo
Yankee Doodle
Oh My Darling Clementine
Call sign
Chime
Synthesized Bell
I've been working on the Railroad
CH 1
Group
Oribiao Kikinagara
She Wore a Yellow Ribbon
Group
Melody Chime
Chime
Iro Howaitoburendo
Oribiao Kikinagara
A September
Doyoubino Koibito
Mamotte Agetai
Runner
ＦＧ
Call sign
Install the product according to the procedure below.
① Create mounting holes on a mounting surface (board thickness: 1mm - 10mm)
where there is enough space for the mounting hardware. (See the mounting dimensions diagram)
② (a) Insert the product from the front of the mounting surface.
(b) Attach the mounting hardware which comes with the product to the holes on the side of the product.
(c) Then fasten the screws of the mounting hardware. (Recommended fastening torque: 0.7±0.1N・m)
③ Confirm that the product and the mounting hardware are installed properly.
17
Amairono Kamino Otome
25
I Don't Want to Miss a Thing
18
Les Champs-Elysees
01
Beep (slow intermittent horn)
09
Stutter + Bell
02
Stutter (rapid intermittent horn)
10
Synthesized Melody
26
Yozorano Mukou
03
Bell (clear highpitched bell)
11
Chime
19
Canon
27
Aiwa Katsu
04
Yelp (rapid siren)
12
Call sign
20
Rara Sanshain
28
Truth
07
Synthesized Piano
15
The Entertainer
08
Synthesized Bell
16
Amazing Grace
22
Oshiete
30
14
Top of the World
21
Uchuusenkan Yamato
24
Gonna Fly Now(Theme for "Rocky")
Odoru Ponpokorin
23
Makenaide
32
Haruyo Koi
31
Imasugu Kisu Mi
05
Rapid Hi-Lo
13
Can't Take My Eyes off of You
06
Melody Chime
29
Gattsudaze
06
Melody Chime
29
Yellow Rose of Texas
05
Rapid Hi-Lo
13
Oribiao Kikinagara
Yankee Doodle
23
Toys Go Cha Cha Cha
32
Londonderry Air
31
When the Saints Go Marching In
22
Bear Song
30
14
A September
21
I've been working on the Railroad
24
Konnako Irukana
08
Synthesized Bell
16
Akino Kehai
07
Synthesized Piano
15
Doyoubino Koibito
20
Hi Ho
28
Oh My Darling Clementine
04
Yelp (rapid siren)
12
Mamotte Agetai
26
Rudolph the Red-nosed Reindeer
03
Bell (clear highpitched bell)
11
Runner
19
Happy Birthday
27
She Wore a Yellow Ribbon
02
Stutter (rapid intermittent horn)
10
Call sign
01
Beep (slow intermittent horn)
09
Chime
17
Saafu Tengoku Sukii Tengoku
25
Wiegenlied
18
Iro Howaitoburendo
3. Part Names
Mounting dimensions diagram
●Be sure to turn the power off before installing the product.
Failure to do so may cause electric shock.
●Be sure to let specialists perform installation task which requires construction work.
Failure to do so may cause electric shock, fire, or falling.
●Secure a enough space in which the mounting hardware can also be installed when choosing
a mounting surface.
●Install the product on a flat surface without bumps and dips. Failure to do so may weaken its
resistance to water and dust.
●To prevent the product from falling in places where vibration may be generated, apply thread
locking adhesive or the like, and perform periodic checking of the tightness of the mounting hardware.
●When mounting it at a high place, choose the place where a foothold exists for facilitating repair work.
●If it used under the connected state to the power supply, then provide a switch which can easily
cut off power supply in proximity to the main body, for the safety purpose.
●Choose a location for the mounting surface where it has enough strength to support
the weight of the product, and where there is less vibration. Failure to do so may be
the cause of injury or damage to the product.
●Be sure to use both pieces of mounting hardware, and fasten them with the
recommended fastening torque. Failure to do so may be the cause of injury
or damage to the product.
Mounting
hardware
Warning
Caution
Other Precautions
Volume control
06
Melody Chime
29
Romance De Amour
05
Rapid Hi-Lo
13
For Elise
Petrouchka
23
On the Avignon bridge
32
Ave Maria
31
Grandfathers Clock
22
Blacksmith in the village
30
14
Maiden's Prayer
21
Cuckoo
24
Daydream Believer
08
Synthesized Bell
16
Annie Laurie
07
Synthesized Piano
15
Minuet
20
The camptown Races
28
Mountain musician
04
Yelp (rapid siren)
12
Call sign
26
Symphony No.40
03
Bell (clear highpitched bell)
11
Chime
19
Mary had a little Lamb
27
Silent Lakeside
02
Stutter (rapid intermittent horn)
10
Synthesized Melody
01
Beep (slow intermittent horn)
09
Stutter + Bell
17
London bridge is falling down
25
Amaryllis
18
Holdiridia
A