Instruction Manual

ManualsBrandsPATLITE ManualsAudioBD

●Make sure that there is no misalignment with the sound group

selection switch when selecting.

If there is misalignment as shown in the figure on the right, the

sound group selected may not play.

6-2. Selecting a Sound Group

Use the sound group selection switch to select a group from the 16 types

from A to P. Use a flat-blade screwdriver with the blade thickness of 1.0mm or

thinner for turning the switch. (Factory default setting: Sound group A)

When the sound group P is selected, any sound may be combined freely

using an SD card. (Factory default setting: See the table below)

Refer to the section 6-3. How to Combine Sounds for details.

Author 13:BEETHOVEN VAN LUDWIG 14:BADARZEWSKA BARANOWSKA TEKLA 15:BACH JOHANN SEBASTIAN

　　　 16:SCOTT LADY JOHN DOUGLAS 17･18･21･25･28･29:TRADITIONAL 19･27:PD

20:FOSTER STEPHEN COLLINS 22:Song authorized by the Ministry of Education

23:WERNER HEINRICH (DE 2) 24:STEWART JOHN C

:MOZART WOLFGANG AMADEUS 30:BLANTER MATVEJ ISAAKOVICH

31:WORK HENRY CLAY 32:SCHUBERT FRANZ　　

Author 13:CREWE BOB 14:CARPENTER RICHARD LYNN 15:JOPLIN SCOTT 16:CARRELL JAMES P

17:

Kouichi Sugiyama

18:WILSHAW MICHAEL 19:PACHELBEL JOHANN 20:Ijichi Hiromasa

21:Hiroshi Miyagawa 22:Takeo Watanabe 23,30:Tetsuro Oda 24:CONTI BILL 25:WARREN DIANE EVE

26:

Yuka Kawamura

27:KAN 28:

Masahiro Andoh

29:

Totasu Matsumoto

31:

Tatsuya Hirakawa

32:

Yumi Matsutoya

Beep (slow intermittent horn)

Rapid Hi-Lo

ＣＨ１

Stutter (rapid intermittent horn)

ＣＨ２

Bell (clear highpitched bell)

ＣＨ３

Yelp (rapid siren)

ＣＨ４

Ａ

Group

Stutter(rapid intermittent horn)

Bell(clear highpitched bell)

Synthesized Melody Chime

Melody Chime

Chime

Synthesized Piano

Call Sign

Synthesized Bell

Ｃ

Ｂ

Minuet

London Bridge is falling down

Fur Elise

Annie Laurie

Maiden's Prayer

Chime

Call Sign

Ｅ

Ｄ

Mary had a little lamb The Camptown Races

Holdiridia

Chime

Call Sign

Ｇ

Ｆ

Amaryllis

Silent Lakeside

Romance De Amour

On the Avignon bridge

Symphony No. 40

Daydream Believer

Chime

Call Sign

Ｊ

Ｉ

Cuckoo Blacksmith in the village Chime Call Sign

Ｈ

Mountain musician

Petrouchka Chime

Chime

Call Sign

Ｌ

Ｋ

Holdiridia

Mary had a little lamb

Grandfather's Clock

Mountain musician

Ave Maria

Stutter(rapid intermittent horn)

Bell(clear highpitched bell)

Chime

Synthesized Melody Chime

Call Sign

Ｎ

Ｍ

Romace De Amour

Stutter(rapid intermittent horn)

Bell(clear highpitched bell)

Synthesized Melody Chime

The Camptown Races Cuckoo Petrouchka Grandfather's Clock

Ｐ

Ｏ

ＣＨ１ＣＨ２ＣＨ３ＣＨ４

Ａ

Group

Can't Take My Eyes off of You

Top of the World

Ｃ

Ｂ

Amairono Kamino Otome

Canon

The Entertainer

Les Champs-Elysees

Amazing Grace

Ｅ

Ｄ

Uchuusenkan Yamato Oshiete

Rara Sanshain

Ｇ

Ｆ

Aiwa Katsu

Gattsudaze

I Don't Want to Miss a Thing

Truth

Yozorano Mukou

Ｊ

Ｉ

Makenaide

Gonna Fly Now (Theme for "Rocky")

14 Top of the World

Can't Take My Eyes off of You

16 Amazing Grace

15 The Entertainer

Les Champs-Elysees

Amairono Kamino Otome

Rara Sanshain

Canon

Oshiete

Uchuusenkan Yamato

Gonna Fly Now (Theme for "Rocky")

Makenaide

Yozorano Mukou

I Don't Want to Miss a Thing

Truth

Aiwa Katsu

Odoru Ponpokorin

Gattsudaze

Haruyo Koi

Imasugu Kisu Mi

Ｈ

Imasugu Kisu Mi Haruyo Koi

Odoru Ponpokorin

Ｌ

Ｋ

Les Champs-Elysees

Canon

TruthＮ

Ｍ

Gattsudaze

Rara Sanshain

Uchuusenkan Yamato Odoru Ponpokorin Imasugu Kisu Mi

Ｐ

Ｏ

Stutter (rapid intermittent horn)

Beep (slow intermittent horn)

Yelp (rapid siren)

Bell (clear highpitched bell)

Melody Chime

Rapid Hi-Lo

Synthesized Bell

Synthesized Piano

Synthesized Melody Chime

Call Sign

Chime

Stutter(rapid intermittent horn)

Bell(clear highpitched bell)

Maiden's Prayer

Fur Elise

Annie Laurie

Minuet

Holdiridia

London Bridge is Falling Down

The Camptown Races

Mary Had a Little Lamb

Blacksmith in the village

Cuckoo

Daydream Believer

On the Avignon bridge

Symphony No. 40

Amaryllis

Mountain musician

Silent Lakeside

Petrouchka

Romance De Amour

Ave Maria

Grandfather's Clock

Sound groups

Stutter (rapid intermittent horn)

Beep (slow intermittent horn)

Yelp (rapid siren)

Bell (clear highpitched bell)

Melody Chime

Rapid Hi-Lo

Synthesized Bell

Synthesized Piano

Synthesized Melody Chime

Call Sign

Chime

Stutter(rapid intermittent horn)

Bell(clear highpitched bell)

Beep (slow intermittent horn)

Rapid Hi-Lo

Stutter (rapid intermittent horn)

Bell (clear highpitched bell) Yelp (rapid siren)

Stutter(rapid intermittent horn)

Bell(clear highpitched bell)

Synthesized Melody Chime

Melody Chime

Chime

Synthesized Piano

Call Sign

Synthesized Bell

Chime

Call Sign

Chime

Call Sign

Chime

Call Sign

Chime Call Sign

Chime

Call Sign

Stutter(rapid intermittent horn)

Bell(clear highpitched bell)

Chime

Synthesized Melody Chime

Call Sign

Stutter(rapid intermittent horn)

Bell(clear highpitched bell)

Synthesized Melody Chime

We thank you for purchasing PATLITE Audible Alarm. Before you start using the product,

please read this instruction manual carefully to use the product correctly. Please store

this document in a safe place. Be sure to read this document again when you are about

to perform tasks such as maintenance and repair.

And if you have any questions, contact a branch office or the technical support printed on

the last page.

Instruction Manual

Audible Alarm

TYPE : BD

Front panel

The precautions which must be observed to prevent damage to the person using the

product, to people around it, or to property are described in a manner shown below

■The seriousness of injury or damage caused by ignoring the indication and using the

product in a wrong way is categorized with the indications below and descriptions are

added to each of them

Warning

The sections with this indication contain "items which could

cause death or serious injury" if ignored.

The sections with this indication contain "items which could

cause injury or property damage only" if ignored.

Caution

Safety Precautions

●Be sure to turn the power off before wiring or installing the product. Failure to do

so may cause electric shock.

●Take care to perform wiring correctly. If the wiring in incorrect, internal circuit may

be damaged by fire, and it may also be a cause of fire.

●As for the power source, be sure to use this product within the allowable range

of voltage. Failure to do so may be a cause of fire or damage to the product.

●When the product is used for security purposes in which safety is emphasized,

be sure to perform daily maintenance, and design a system which is capable

of tackling the occurrence of unlikely event such as malfunctioning or failure.

●Be sure to let specialists perform installation task which requires construction work.

Failure to do so may cause electric shock, fire, or falling.

●Before you start working on the product, discharge static electricity

from your body. By touching another grounded metal part with bare hand,

the static electricity can be discharged.

●To protect power source circuit and internal circuit of the product,

be sure to install external fuse.

Failures caused by using the product in ways not observing the Warnings and Cautions,

by disassembling or converting the product, or by natural disaster are not covered under

warranty. And do not use the product in ways other than the ways described in this

document.

●Use the product in an environment where there is no electromagnetic or inductive

noise. Speakers are known to generate noise.

●Use the product in an environment where there is no corrosive gas.

Failure to do so may cause malfunction.

●Do not use the product as fire alarm.

1. Cautions Which Must Be Observed for Safety Use

2. Model Indicating Format

3. Part Names

Case

Install the product according to the procedure below.

① Create mounting holes on a mounting surface (board thickness: 1mm - 10mm)

where there is enough space for the mounting hardware. (See the mounting dimensions diagram)

② (a) Insert the product from the front of the mounting surface.

(b) Attach the mounting hardware which comes with the product to the holes on the side of the product.

(c)

Then fasten the screws of the mounting hardware. (Recommended fastening torque: 0.7±0.1N・m)

③ Confirm that the product and the mounting hardware are installed properly.

4. How to Install

Sound group

Selection switch

Mounting screw for front

cover (M3X6)

Waterproofing rubber

for the slot

Card slot

Mounting hardware

(attachments)

Terminal cover

(b)

(c)

(a)

Mounting surface

(board thickness: 1mm - 10mm)

SD card

(Model: SDV-2GP Sold separately)

* PATLITE Corporation is a member of

the SD Card Association

Front cover

Volume control

Air duct

□68 mm

Mounting dimensions diagram

* Dimensions of the mounting holes

conform to IEC-61554 (DIN-43700)

Terminal block

(screw M3X6)

■Normal-rated voltage

24 : 12-24V DC

100：100/220Ｖ AC

■Sound Chart type

A：Type A

C：Type C

D：Type D

E：Type E

■Color of body front

J : Light gray

K : Dark gray

+0.7

(104mm)

●Be sure to turn the power off before installing the product. Failure to do so may cause electric shock.

●Secure a enough space in which the mounting hardware can also be installed when choosing a mounting surface.

●

Install the product on a flat surface without bumps and dips. Failure to do so may weaken its resistance to water and dust.

To prevent the product from falling in places where vibration may be generated, apply thread locking adhesive or the like,

and perform periodic checking of the tightness of the mounting hardware.

●Install the product in a way the air ducts are not blocked.

●Keep a space more than 6.3mm between the terminal block and the metal surface.

●Choose a location for the mounting surface where it has enough strength to support the weight of the product, and where

there is less vibration. Failure to do so may be the cause of injury or damage to the product.

●Be sure to use both pieces of mounting hardware, and fasten them with the recommended fastening torque. Failure to do

so may be the cause of injury or damage to the product.

Before wiring the product, remove the terminal cover. And after the completion of the

wiring attach the terminal cover.

For the external contact of signal line, use no-voltage contact circuit such as relay switch

or open collector circuit (NPN type). As for the contact capacity, see the table below.

5. How to Perform Wiring

Wiring examples

●BD-100

●Be careful not to lose the terminal cover.

●The use of M3 ring terminals with insulating coating is recommended for the wiring of terminal block to prevent

disconnection of wires.Recommended product: N1.25-3 produced by JST Mfg. Co., Ltd.

(Product confirming to RoHS)

●When the product is to be used in a condition in which it is connected to power source, install a switch near the

main body to be able to turn off the power easily for safety reasons.

●Confirm that the wiring has been performed correctly before turning on the power.

●Be sure to turn the power off before you start wiring. Failure to do so may cause electric shock.

●Be careful not to make a mistake in wiring. Moreever wire for neither 100V nor 220V at the same time

in the case of BD-100.

Failure to do so may cause damage to the internal circuit by fire, and it

may cause fire.

●The terminal screws should be fastened with the recommended fastening torque (0.3N・m). Failure to do so may

cause short circuit due to disconnection of wire, and damage to the product.

●When the product is used in places where vibration occurs, perform periodical checking of the tightness of the

terminal screws to prevent letting go of the wires.

●To protect the power source circuit and the internal circuit of the product, be sure to install an external fuse.

No Use

●Sound Chart type A (BD-□A)

Sound List

1mm

12-24V DC

6-1 Opening and Closing the Front Cover

Open or close the front cover according to the procedure shown below when

performing tasks such as adjusting the volume of the sound or selecting the tone color

group.

①

Loosen the mounting screw (M3X6) for the front cover.

(An screw does not fall out.)

② Push the lower front cover section (part A in the figure on the right)

lightly with finger to slide it downward.

③ When a SD card is to be used, remove the waterproofing rubber for the slot.

④ After completing tasks, attach the parts removed in the procedure from ① to ③

in the opposite order.

(Recommended fastening torque for the mounting screw: 0.3N・m)

●Be careful not to lose the waterproofing rubber for the slot.

●Do not try too hard to slide down the front cover. To do so may cause the front cover to disassemble.

●Attach the waterproofing rubber for the slot securely. Failure to do so may weaken the product's resistance

to water and dust.

● Fasten the mounting screw for front cover with the recommended fastening torque. In places where

vibrations occur, the front cover may fall or the product may be damaged.

Ａ

6. How to Use the Product

Waterproofing

rubber for the slot

Volume control

Mounting screw

for front cover

(M3X6)

Front cover

Card slot

Sound group

selection switch

Sound groups

●Sound Chart type C (BD-□C)

Sound List

BD - 24 A - J

Mounting

hardware

Withstand voltage

Current capacity

Leakage current

ON voltage (Vsat)

DC12V or higher

7mA or higher

0.1mA or lower

1V or lower

(0.5V or lower in case of DC12V)

●Contact capacity

BD-24

BD-100

5.5A/6ms at maximum

None

●Inrush current

Warning

Caution

Warning

Caution

When circuit is opened: DC12V

When circuit is closed: 7mA

COM

CH1

CH2

CH3

CH4

Wiring when

NPN transistor is used

CH sideCOM side

Fuse

125V 0.5A

Warning

Caution

Other Precautions

External

point of

contact

Sound

Signal line

COM

7mA

←

12V

NPN Open Collector Curcuit

When circuit is opened: DC12V

When circuit is closed: 7mA

COM

* Do not connect the power

sources of 100V and 220V

simultaneously.

CH1

CH2

CH3

CH4

Fuse

250V 0.5A

Fuse

125V 0.5A

220V AC

100V AC

Wiring when

NPN transistor is used

CH sideCOM side

●BD-24

Do not supply a voltage for the signal line.

Failure to do so may be damaged to the product.

C95100106 E