ASSEMBLY INSTRUCTIONS RESIN GARDEN SHED SKU: T-PS23-0383A-DGY BE YOUR LIFE BUILDER www.patiowell.com Resin Garden House Installation Tutorial https://www.patiowell.com/ pages/video-t-ps23-0383a-dgy saleservice@patiowell.
SITE PREPARATION Level the ground surface. cem ent Recommendation: Construct a wooden or concrete base as a foundation. The external dimensions of the product : 76.6’’ 76.2’’ 48.
BEFORE STARTING ASSEMBLY Remove all of the pieces from the 1 package and spread them out on the ground. Before installation, please check the type and quantity of parts first. It is recommended to use a clean work surface to spread the parts out and for pre-assembly steps. Review all instructions before you begin, continue to refer to instructions during assembly. Be sure to follow all steps thoroughly. Please prepare these components in advance at the beginning of each stage.
FLOOR PARTS A1 X4 A2 X2 WALL PARTS B1 X2 B2 X4 B3 X1 B5 X2 B4 X2 B1-1 X1 B1-2 X1 B4-1 X2 04
WINDOW PARTS W1 X2 W2 X1 ROOF PARTS F1 X2 F2 X2 F3 X2 C7 X2 F4 X1 F5 X1 F6 X1 C1 X1 C2 X1 C3 X1 C4 X1 C5 X1 C6 X1 E2 X1 E3 X1 05
DOOR PARTS D1-2 X2 D1 X1 D1-4 X1 D1-1 X1 ACCESSORIES C7-1 X2 F4-1 X1 F4-2 X1 E1 X2 D1-3 X1 D1-1-2 X2 D1-2-1 X1 B1-2-1 X1 A1-1 X4 06
SCREW cm 131+2 pcs 1 inch 2 0.5 3 1 12+2 pcs inch 1 M5*14 2 0.5 SC4x30 44+2 pcs 1.5 SC5x14 cm cm 4 3 1 1 inch 2 0.5 3 1 1.5 SC5x30 cm 4 4+2 pcs 1.5 inch 1 SC5x12 M4*30 M5*30 2 0.5 4 3 1 4 1.5 M5*12 CHOOSE THE LOCATION OF THE WINDOW There are four ways to install wall panels with windows, and our instructions show the fourth way of installation.
CONTENTS Floor Part Instruction 09-12 (page) Wall Part Instruction 12-19 (page) Roof Part Instruction 20-26 (page) Door Part Instruction 27-30 (page) 08
STEP 1 A2 A1 STEP 2 A1 A2 A1 09
STEP 3 A1 A1 A2 A1 STEP 4 A1 A2 A1 A2 A1 10
STEP 5 A1 A2 A1 A1 A2 Insert A1 at an angle.
STEP 6 SC5x14 Screw position SC5x14 12 pcs STEP 7 ① ② W2 W1 W2 W1 W1 Textured side facing down.
STEP 8 B1 B1 STEP 9 B2 B1 13 B1
STEP 10 B4 STEP 11 B2 14
STEP 12 B5 B5 STEP 13 B2 15 B5
STEP 14 B5 B5 B5 STEP 15 B2 16
STEP 16 B4 STEP 17 B3 17
STEP 18 B1 STEP 19 Note: After installing B1-1, B1-2 in B1-1/B1-2 sequence, please measure whether the size is equal to 30mm (as shown in the picture).
STEP 20 Do not hit the screws here yet. B4-1 SC5x14 SC5x14 15 pcs STEP 21 Do not hit the screws here yet.
STEP 22 Note the snaps on C7-1. C7-1 C1 C7 SC5x14 C2 SC5x14 C3 For Front Door SC5x14 3 pcs STEP 23 Note the snaps on C7-1.
STEP 24 SC5x14 SC5x14 SC5x14 6 pcs STEP 25 SC5x14 SC5x14 21 SC5x14 7 pcs
STEP 26 E2 SC5x12 E3 SC5x12 4 pcs STEP 27 E1 SC5x14 22 SC5x14 4 pcs
STEP 28 SC5x30 SC5x30 4 pcs STEP 29 SC5x30 F3 F2 F1 23 x2 SC5x30 12 pcs
STEP 30 F3 F2 F1 F1 F2 F3 24 Adjusting roof and wall joints with a scraper.
STEP 31 F6 F5 F4-2 F4-2 F4 F4-1 F4-1 STEP 32 F4-1 CLICK 25
STEP 33 Note: Another person should be on the outside to hold down the roof while the screws are being driven.
STEP 34 D1-2 167.8mm √ D1-4 D1-1 D1 D1 × SC5x14 Note: After installing D1, D1-1, D1-4, D1-2 in sequence, please measure whether the size is equal to 167.8mm (as shown in the picture).
STEP 36 B1-2-1 SC4x30 SC4x30 SC4x30 6 pcs STEP 37 A1-1 28 x4
STEP 38 SC5x30 29 SC5x30 26 pcs
CARE & SAFETY • In case of fire, do not attempt to extinguish any burning polypropylene with water Unsuitable for storage of flammable or corrosive substances. • It is of utmost importance to assemble all of the parts according to the directions. Do not skip any step. • Please consult your local authorities if any permits are required to erect shed. • Periodically check shed to assure that it remains stable and that the site remains level.