Installation Instructions

OMNPMD75-EI00
PRINTED IN CANADA 06/2003
Installation
At the recommended height of 2.1m (7ft) ±10%, the OMN-PMD75 motion detectors
provide full coverage from 1.5m (5ft) to 11m (35ft). The installation height is measured
from the center of the detector as shown in figure 4.
Avoid bending, cutting or altering the antenna or mounting the detector near
or on metal as this may affect signal transmission.
Avoid placing the detector within proximity of the following sources of interference:
reflective surfaces, direct air flow from vents, fans, windows, sources of steam/oil
vapor, infrared light sources and objects causing temperature changes such as
heaters, refrigerators and ovens.
Do not touch the sensor surface as this could result in a detector
malfunction. If necessary, clean the sensor surface using a soft cloth with
pure alcohol.
PCB Height Adjustment
The OMN-PMD75 is designed for optimal performance at a height of 2.1m (7ft), but
can be installed lower or higher. After you have installed the detector, ensure that the
adjustable height markings on the right side of the PCB matches the tab inside the
back cover.
For example, if the detector is installed at a height of 2.1m (7ft), the PCB should then
be adjusted to 2.1m (7ft). Align the desired marking (height) with the back cover’s
plastic tab (figures 1 and 3).
If another installation height is called for, readjust the PCB accordingly. Any PCB
adjustments should be followed by a walk-test of the protected area. Walk-testing
verifies that the required coverage is in place.
LED Setting (J5)
This setting enables or disables the red LED. The red LED will illuminate for a period
of 4 seconds to indicate detected movement. The motion detector performs a battery
test every 12 hours. If the battery voltage is too low, the red LED will flash at 5-second
intervals. The red LED indicator light will blink rapidly when the motion detector
transmits a signal to the receiver. Refer to table 1.
Digital Shield™ Setting (J4)
In Normal Shield mode, the detector is set for normal environments. In High Shield
mode, the detector is set for high-risk environments (potential interferences) and
therefore provides greatly increased false alarm immunity. However, response time
and detector speed may be slower. Refer to table 1.
Single or Dual Edge Processing (J3)
This setting determines the DSP (Digital Signal Processing) operational mode of the
detector. Single Edge Processing mode should be used in normal environments with
minimal sources of interference. Dual Edge Processing Mode provides better false
alarm rejection in the case where the detector is placed near sources of interference
that can adversely affect the motion detector. Refer to table 1.
Check-in Supervision Timer (J1, J2)
These two jumpers set the time interval at which the motion detector will communicate
a check-in signal. Refer to table 1.
Powering the Detector
1. Insert three “AAA” batteries into battery holder while verifying polarity (figure 3).
2. Insert the battery holder into the back cover and connect the battery connector to
the PCB.
After connecting the battery connector, a power-up sequence will begin
(lasting 10 to 30 seconds). During this time, the red LED will flash and
the detector will not detect an open zone or tamper.
Replacing Batteries
1. Disconnect the battery connector from the PCB. Remove the battery holder and
remove the old batteries.
2. Press and release the anti-tamper switch to ensure that the unit has been powered
down.
3. Follow the steps outlined in “Powering the Detector”.
Walk-testing
At 20°C (68°F), in Normal Shield (J4 = ON) mode and Single Edge Processing mode
(J3 = ON), you should not be able to cross more than one complete zone (consisting
of 2 beams, left and right sensor detecting elements) in the coverage area with any
kind of movement; slow/fast walking or running. In High Shield mode, the amount of
movement required to generate an alarm is doubled. The approximate width of a full
beam at 11m (35ft) from the detector is 1.8m (6ft) (figure ). When walk-testing, always
move across the detection path and not toward the detector.
To Perform a Walk-Test
Open the cover in order to trigger the anti-tamper switch, then snap the cover
back into position. This will activate the motion detector’s walk-test mode for 3
minutes.
Walk-test mode is also activated for 3 minutes once the motion
detector is powered on.
Signal Strength Test
In order to verify the receiver's reception of the motion detector’s signal, perform a
signal strength test as described in the appropriate receiver’s Reference and
Installation Manual before finalizing the installation of the motion detector. Prior to
performing the test, make sure the batteries have been inserted into the battery holder
to power the detector. Also verify that the motion detector has been assigned to a zone
according to the instructions in the appropriate receiver’s Reference and Installation
Manual. If the transmission is weak, relocating the transmitter by a few inches can
greatly improve the reception.
Alive Software
If the motion detector transmits 2 alarm signals (LED on for 4 sec.) within a 5-minute
period, the detector will fall into Energy Save Mode where it will not transmit any alarm
signals for approximately 3 minutes. Due to the motion detector’s Alive Software, the
red LED will continue to flash to indicate a detection even when in Energy Save Mode.
Once the 3-minute Energy Save Mode ends, the motion detector returns to normal
operation.
If the detector’s cover is removed and then replaced while in Energy Save
Mode, the first detection will trigger an alarm signal.
Figure 1 : Back Cover
Figure 2 : Beam Dispersion
Figure 3 : Detector Overview
Figure 4 : PCB Settings
:
Table 1: Jumper Settings
U=default
After changing the jumper settings, snap the cover into place to close the
anti-tamper switch or press and release the anti-tamper switch in order to
save the changes.
868MHz (only) compliant to all EU and EFTA countries except Greece
according to RTT&E directives.
Changes or modifications on equipment not expressly approved by Paradox Security
Systems could void the user’s authority to operate the equipment.
© 2002-2003 Paradox Security Systems Ltd. All rights reserved. Specifications may change without prior notice. One or more of
the following US patents may apply: 6215399, 6111256, 5751803, 5721542, 5287111, 5119069, 5077549, 5920259, 5886632.
Canadian and international patents may also apply. LODIFF® lens: patent #4,787,722 (U.S.). Omnia and Shield are trademarks
or registered trademarks of Paradox Security Systems Ltd. or its affiliates in Canada, the United States and/or other countries.
LODIFF® is a registered trademark of Fresnel Technologies Inc.
Warranty
The Seller warrants its products to be free from defects in materials and workmanship under normal use for a period of one year.
Except as specifically stated herein, all express or implied warranties whatsoever, statutory or otherwise, including without
limitation, any implied warranty of merchantability and fitness for a particular purpose, are expressly excluded. Because Seller
does not install or connect the products and because the products may be used in conjunction with products not manufactured by
the Seller. Seller cannot guarantee the performance of the security system. Seller obligation and liability under this warranty is
expressly limited to repairing or replacing, at Seller’s option, any products not meeting the specifications. In no event shall the
Seller be liable to the buyer or any other person for any losses or damages whether direct or indirect or consequential or
incidental, including without limitation, any damages for lost profits stolen goods, or claims by any other party, caused by defective
goods or otherwise arising from the improper, incorrect or otherwise faulty installation or use of the merchandise sold.
Instructions
OMN-PMD75
A
-Corner mount
B
- Flat surface mount
C
-Plastic tab
A
A
A
A
B
B
B
B
C
- all measurements shown in
meters and (feet)
90°
3m
(10ft)
3m
(10ft)
1.5m
(5ft)
1.5m
(5ft)
0m
0m
2.1m
(7ft)
1.5m
(5ft)
3m
(10ft)
6m
(20ft)
9m
(30ft)
11m
(35ft)
A
B
C
D
F
J5
J4
J3
J2
J1
E
A
- Battery connector
B
- Anti-tamper switch
C
- PCB adjustment
D
- Antenna
E
-Sensors
F
-LED
G
- Jumpers
H
- Battery holder
I
-Plastic tab
Correct
Incorrect
G
A
H
I
- Optimum beam dispersion.
- Unit aims further, the gap
between beams is wider. Pet
immunity is compromised.
- Unit aims closer, the gap
between, beams is smaller. Pet
immunity is compromised.
Height = 2.1m (7ft)
PCB Adj. = 2.1m (7ft)
PCB Adj. = 1.1m (4ft)
PCB Adj. = 3.1m (10ft)
Height = 2.1m (7ft)
Height = 2.1m (7ft)
J5 LED Indicator
OFF = Disabled
ON = Enabled U
J4
Digital Shield (Sensitivity)
OFF = High Shield (low sensitivity)
ON = Normal Shield U (high sensitivity)
J3
Processing Type
OFF = Dual Edge
ON = Single Edge U
J2
Base Time
OFF = Minutes
ON = Hours U
J1
Time Value
OFF = 6
ON = 12 U
TECHNICAL SPECIFICATIONS
Number of Sensors Two
Sensor Type Dual Element Infrared
Sensor Geometry Rectangular
Coverage - 90° (standard) 11m x 11m (35ft x 35ft)
Pet Immunity Up to 40kg (90lbs)
Walk Speed 0.2m to 3.5m/sec. (0.6ft to 11.5ft/sec.)
Installation Height 2.1m to 2.7m (7ft to 9ft)
Operating Temperature +0°C to +50°C (32°F to 122°F)
RF Frequency
433 or 868MHz
Lens 2nd generation Fresnel lens, LODIFF®, segments
Power 3 X “AAA” alkaline batteries
Transmitter Range 150m (500ft)
Anti-Tamper Switch Yes
Battery Life
Check-in Setting
Lowest 3 years
Highest 1.5 years
6 min
12 min
6hr 12 hr