All-In-One Wireless Security System V2.0 Model #: MG-6130 / MG-6160 Reference and Installation Manual We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www.paradox.com and send us your comments.
Table of Contents Introduction................................................... 3 About Magellan and this Manual............................. 3 Conventions ............................................................ 3 Specifications.......................................................... 3 Quick Setup................................................... 4 Installation..................................................... 7 AC Power................................................................
Wireless PGM Activation Event ............................. 35 Wireless PGM Deactivation Event......................... 35 Wireless PGM Delay.............................................. 35 System Settings .......................................... 36 Software Reset ...................................................... 36 Installer Lock.......................................................... 36 Console Tamper Supervision ................................ 36 Console Audible Trouble Warning ..............
Introduction About Magellan and this Manual Specifications Magellan is designed for fast and easy installation. Simply remove it from the box, mount the console and wireless transmitters, apply power, perform some basic programming and Magellan is ready to protect your home. Power input: AC*: 12Vac, 1A transformer or 16.
Quick Setup Follow these steps to quickly set up Magellan with the required settings for a basic security installation. Profile” menu or press the [6] key to immediately access the “Zone Profile” menu. For more in-depth programming of the console’s communication features, see Reporting and Dialer Settings on page 27. 1.Getting Started 1. After powering up for the first time, the language selection option will appear. Select the desired language. 2. Press [START] to access the Installer menu. 4.
WARNING! When testing the hardware, the speaker and sirens will also be tested. Avoid close proximity to the Magellan console when performing the hardware test to avoid any damage to your hearing. 8.Time and Date 1. Press the [MENU] key. When you are done the next menu option will appear. Press [NEXT] until you see the “Passwords” menu or press the [8] key to immediately access the “Passwords” menu. 2.
Adding Outputs 1. From the “Output Profile” menu, press [OK]. 2. Select which output you wish to add, modify or delete by pressing [NEXT] and then [OK] when the desired output number appears. 3. Select what type of output you wish to add. Press [YES] for a wireless output, or [NO] for a hardwired output. For hardwired, follow the menus to configure the output. 4. If you are adding a wireless output, press the tamper switch on the transmitter you wish to assign to the selected zone.
Installation AC Power Backup Battery Pack Magellan requires a 12Vac (1A) or 16.5Vac (1A) transformer (not included) to supply power to the console. Connect the transformer to the AC terminals as shown in Figure 1 on page 7. Magellan uses a backup battery pack to provide power during a power loss. A 7.2Vdc 1.8Ah NiMH (Nickel Metal Hydride) rechargeable battery pack is included with the Magellan console. Connect the battery pack as shown in Figure 3 on page 7.
Figure 4: Auxiliary Output Connection Devices such as a light, etc. Insert the device’s wires into the AUX AND C terminals. Telephone Line Connections The Magellan console can be connected to a telephone line by connecting the telephone company’s wires directly to Magellan’s dialer or by connecting a standard 4-pin RJ-11 cable between the LINE plug of the console to a standard telephone wall jack. Direct Connect Connect the telephone line through a RJ31X jack as shown in Figure 5 on page 8.
Normally Closed (N.C.) as detailed in PGM Normal State (Onboard Only) on page 35. Hardwire Zone Connections If the current draw on the PGMs is to exceed 100mA, we recommend using an external relay as shown in Method 2 in Figure 7 on page 9. For connecting PGM2, see Figure 8. Magellan comes with two on-board hardwire zones. You can connect hardwire detection devices such as door contacts to Magellan’s zone terminals. Connect the detection devices as shown in Figure 9 on page 9.
Figure 11: Connecting the UIP-256 WinLoad Connection The Magellan console can be programmed and monitored through the WinLoad Installer Upload/Download Software for Windows®. WinLoad allows for remote or on-site uploading and downloading using most standard modems. It also allows for advanced printing of reports and supports several languages simultaneously. Connect Magellan to a computer containing the WinLoad software as shown in Figure 10 on page 10.
apply power to the console. For more information, see Programming Using a Paradox Memory Key on page 13. Figure 14: Wall Plate B Figure 13: Connecting a Paradox Memory Key (PMC-3) A (x7) C Figure 15: Mounting Magellan onto the Wall Plate Jumper ON: Read from and/or write to memory key Jumper OFF: Write protected (read from memory key only) The installer should verify the proper installation of the memory key.
4. Slide the Magellan’s open slots labeled D (see Figure 16 on page 11) onto the wall plate’s tabs labeled B (see Figure 15 on page 11). 5. Gently apply downward pressure to insert the wall plate’s tabs into Magellan’s open slots. 6. Insert two screws through the wall plate’s screw holes labeled C and into holes labeled E (see Figure 15 on page 11 and Figure 16 on page 11) in the Magellan back plate. This will secure the console to the wall.
Programming Methods WinLoad Installer Upload/Download Software Program the Magellan console remotely or on-site using the WinLoad Installer Upload/Download Software for Windows®. For more information, contact your local Paradox Distributor or visit our Web site at paradox.com. If you are using the WinLoad software, you must program the features explained on page 38. Please refer to WinLoad’s Online Help for more information on using WinLoad.
User Codes A person must be assigned to a User code in order to have access to Magellan. A User code defines the extent of a user’s access to the system and consists of a code # (PIN) and user options. Magellan supports one Installer code, one Maintenance code and up to 16 User codes (one System Master code and 15 User codes). Installer Code Used to program all console settings except User codes and remote controls.
Zone Programming Magellan supports up to 32 wireless zones whereby each zone can be configured with a different zone definition and option. Each zone can also have a voice label recorded for it. Magellan’s zones can be programmed using section programming or through the Installer menu. See Quick Setup on page 4 for more information on zone programming using the Installer menu.
Follow/Stay Zones Figure 21: Delayed Fire Zone Sections [001] to [032]: Zones 1 to 32, 3-digit # = 004 Follow/Stay zones function as follows: • • All zones defined as Follow/Stay zones become Follow zones (refer to Follow Zones on page 15) when the Magellan system is Regular armed. All zones defined as Follow/Stay zones become Stay zones when the Magellan system is Stay or Instant armed.
24Hr. Gas Zones Bypass Option Sections [001] to [032]: Zones 1 to 32, 3-digit # = 012 Section [001] to [032]: Zones 1 to 32; Option [2] When a 24Hr. Gas zone opens, whether it is armed or disarmed, the console will immediately generate an alarm. The SIA FSK reporting format includes specific report codes to identify the alarm as a Gas alarm (see Appendix 1: Automatic Report Code List on page 39). Option [2] OFF = Bypass option disabled Option [2] ON = Selected zone is Bypass enabled (default) 24Hr.
• • • During the Intellizone Delay, a second zone has caused an alarm. During the Intellizone Delay, the zone in alarm has restored (closed) and re-occurred (opened). The zone in alarm is still open after the Intellizone Delay has elapsed. This feature is not for use in UL installations.
Table 3: Wireless Doorbell Tones Assigning Wireless Zone Transmitters Section [096] - Options [1] and [2] Sections [201] to [232]: Zones 1-32; Wireless Transmitters 1-32 Sections [201] to [232] represent zones 1 to 32. A wireless transmitter assigned to a section ([201] to [232]) will be assigned to the zone represented by the section. For example, a wireless transmitter assigned to section [205] will be assigned to zone 5.
The signal strength can also be verified by performing a system test. See Quick Setup on page 4 for more information. Although remote controls can be assigned by the System Master, the remote control’s buttons are programmed by the installer. Assigning Remote Controls The Magellan console accepts up to 16 fully programmable remote controls. Every User code can have one remote control assigned to it. To assign a remote control: Each remote control can be programmed to perform different actions.
Button Options Table MG-REM1 MG-REM2 0 - Button disabled 1 - Regular arming 2 - Stay arming 3 - Instant arming 4 - Force arming 5 - N/A 6 - N/A 7 - N/A 8 - Panic 1† 9 - Panic 2† A* - Panic 3† B* - PGM Activation (Event Group #7, see Appendix 1: PGM Event Table) C* - PGM Activation (Event Group #8, see Appendix 1: PGM Event Table) D* - Turn FM radio ON/OFF (MG-6160 only) E* - FM radio memory scan (MG-6160 only) F* - Non-medical alarm * = Hex values A to F are keys [1] to [6] from Magellan’s Center Keypad.
Arming and Disarming Regular Arming Switches to Stay Arming Section [092]: Option [4] Option [4] OFF = Regular arming switches to Stay arming disabled (default) Option [4] ON = Regular arming switches to Stay arming enabled If a user Regular arms the system, but does not exit through (open and close) an Entry Delay zone during the Exit Delay, the console can be programmed to switch from Regular arming to Stay arming. • • The console will enter a 60-second Exit Delay period before arming the system.
Auto-Arming Options Exit Delay Termination Section [092]: Option [3] Option [3] OFF = Auto-arm system using Regular arm (default) Option [3] ON = Auto-arm system using Stay arm Section [093]: Option [6] Option [6] OFF = Exit Delay Termination disabled Option [6] ON = Exit Delay Termination enabled (default) When using Timed Auto-arming (see page 22) or No Movement Auto-Arming (see page 22), the console can Regular or Stay arm the system.
Alarm Options Bell Cut-off Timer Section [063]: 001 to 255 minutes; 000 = Disabled; Default = 4 minutes After an audible alarm, the siren will stop upon the disarming of the system or when the Bell Cut-Off timer has elapsed, whichever comes first. • When option [8] is ON, the Wireless Transmitter Supervision Options (see page 24) will ignore the bypass definition.
Table 5: Tamper Recognition Options Options Description [3] [4] OFF OFF Tamper Recognition disabled (default) OFF ON Trouble only System armed or disarmed: If a tamper wiring failure occurs on a zone, the console will generate a trouble and send a report to the monitoring station (if programmed). ON OFF Audible alarm when armed System armed: If a tamper failure occurs on a zone, the console will follow the zone's Alarm Types setting (see page 17).
When the Magellan system is in entry delay, the console will send a message to the MG-2WPGM telling it that it is in entry delay. During the entry delay, the MG-2WPGM will check for communication with the Magellan console every 10 seconds and if there is no response from the console, the relay will activate. To enable the backup reporting option: 1. Press [MENU] + [4] + [INSTALLER CODE] + [7]. 2. Using the [NEXT] key, scroll to the [CONSOLE SUPERV?] option. 3. Press [OK]. section [139]).
Reporting and Dialer Settings Report Codes A report code is a 1- or 2-digit hexadecimal value consisting of digits from 1 to F. Each section from [120] to [156] represents a set of up to four specific events and each of these events can be programmed with a separate 1- or 2-digit report code. Only the Ademco Slow, Silent Knight, and Sescoa formats support 1-digit report codes. To program a 1-digit report code, press the [0] key followed by the desired hexadecimal digit or vice versa.
• • Fire Panic: Panic keys [7] and [9] (see page 26) or the appropriate button(s) on a remote control (see page 20) have been pressed. Recent Closing: Reports when an alarm is generated after arming the system within the period defined by the Recent Close Delay (see page 32). • Section [167] • Section [148] • • • Auto-zone Shutdown: A zone communicates more than the programmed number of transmissions in a single armed period (see page 17). Duress: A Duress code is keyed in (see page 14).
• • • • Keypad AC Failure: The AC voltage of a keypad has dropped below recommended limits. Repeater Supervision Loss: The console has lost communication with a wireless repeater. Repeater Battery Trouble: The battery voltage of a repeater has dropped below recommended limits. Repeater AC Failure: The AC voltage of a repeater has dropped below recommended limits.
• • • • The console will repeat the message a programmed amount of times (see Voice Message Repetitions on page 30) if no acknowledgement is immediately received. If no acknowledgement is received before the number of repetitions has elapsed, the console will then call the next programmed Voice Message telephone number and repeat the process.
005 SIA FSK 006 Ademco Express (DTMF 4+2) UL Note: The installer is required to verify the complete compatibility of the DAC Receiver and formats at least once per year. If you are using any report format other than SIA in sections [105] and [106] and you would like to transmit an “A”, press [0] on the main keypad; if you would like to enter a space (non-reportable digit), press the [1] key on the center keypad.
When option [6] is enabled, the Magellan console will dial a telephone number even if no dial tone is present after 3 seconds. Table 9: Telephone Line Monitoring Options Options [2] OFF OFF TLM disabled (default) OFF ON Trouble only: Upon a line test failure, a TLM trouble will appear in the console’s Trouble Display. ON OFF Alarm if System Armed: Upon a line test failure, a TLM trouble will appear in the console’s Trouble Display and if the system is armed, the console will generate an alarm.
Power Failure Report Delay Section [070]: 001 to 255 minutes; 000 = Disabled; Default = 15 minutes The Magellan console will transmit the AC Failure report code programmed in section [149] after the Power Failure Report Delay period has elapsed.
Programmable Outputs A PGM is a programmable output that toggles to its opposite state (i.e. a normally open PGM will close) when a specific event has occurred in the system. For example, a PGM can be used to activate bells or strobe lights, open/close garage doors and much more. When a PGM activates, the control panel triggers any device or relay connected to it. The Magellan console includes two onboard PGMs. It can support up to a total of four PGMs (e.g.
PGM Normal State (Onboard Only) Wireless PGM Deactivation Event Section [090]: Options [7] (PGM1) and [8] (PGM2) Option [7] OFF = PGM1 Normally Open (default) Option [7] ON = PGM1 Normally Closed Section [261] = Wireless PGM1 Deactivation Event Section [263] = Wireless PGM2 Deactivation Event Section [265] = Wireless PGM3 Deactivation Event Section [267] = Wireless PGM4 Deactivation Event Option [8] OFF = PGM2 Normally Open (default) Option [8] ON = PGM2 Normally Closed A PGM toggles to its opposite sta
System Settings Software Reset Section [199] With section [093] option [8] ON, the Magellan’s radio is turned ON automatically after the system is armed (after the Exit Delay Timer has elapsed). Performing a software reset will reset all programmed sections back to the factory defaults. To perform a software reset: 1. 2. Access the installer programming mode (see page 13). Enter section [199].
Trouble Description Clock Loss The time and date were reset to default. To reprogram: 1. Press the [12HRS] key to display the time using the 12-hour clock or the [24HRS] key to display the time using the 24-hour clock. 2. Enter the desired time and then press [OK]. 3. Enter the date and then press [OK]. AC Failure Power failure detected. The system is running on the backup battery pack.
WinLoad Software Settings Panel Answer Options The following two options define how Magellan answers an incoming call from a computer using the WinLoad Installer Upload/Download Software. Answering Machine Override Section [074]: 010 to 255 seconds; 000 = disabled; Default = disabled When using WinLoad to communicate remotely with an installation site that uses an answering machine or service, the answering machine override must be programmed. Using WinLoad, you will call Magellan, hang up, then call back.
Appendix 1: Automatic Report Code List System Event Default Contact ID Report Code when using sections [790] to [795] Default SIA Report Code when using sections [790] to [795] Arming with Master Code (##) 3 4A1 - Close by user CL - Closing Report Arming with User Code (##) 3 4A1 - Close by user CL - Closing Report Arming with Keyswitch (##) 3 4A9 - Keyswitch Close CS - Closing Keyswitch Auto Arming 3 4A3 - Automatic Close CA - Automatic Closing Arm with PC software 3 4A7 - Remote arm/disarm
System Event Default Contact ID Report Code when using sections [790] to [795] Default SIA Report Code when using sections [790] to [795] AC Failure 1 3A1 - AC loss AT - AC Trouble Battery Failure 1 3A9 - Battery test failure YT - System Battery Trouble Auxiliary supply trouble 1 3AA - System trouble YP - Power Supply Trouble Bell output current limit 1 321 - Bell 1 YA - Bell Fault Bell absent 1 321 - Bell 1 YA - Bell Fault Clock lost 1 626 - Time/Date inaccurate JT - Time Changed Fire
Appendix 2: Ademco Contact ID Report Code List CID# Reporting Code Programming Value Medical Alarms - 100 100 Medical alarm 01 101 Pendant transmitter 02 102 Fail to report in 03 Fire Alarms - 110 CID# Reporting Code Programming Value 154 Water leakage 29 155 Foil break 2A 156 Day trouble 2B 157 Low bottled gas level 2C 158 High temperature 2D 159 Low temperature 2E 110 Fire alarm 04 161 Loss of air flow 2F 111 Smoke 05 162 Carbon monoxide detected 30 112 Combu
CID# Reporting Code Programming Value 335 Local printer paper out 54 336 Local printer failure 55 337 Expansion module DC loss 56 338 Expansion module low battery 57 339 Expansion module reset 58 341 Expansion module tamper 59 342 Expansion module AC loss 5A 343 Expansion module self-test fail 5B 344 RF receiver jam detect 5C Communication Troubles - 350 and 360 Reporting Code Programming Value 408 Quick arm 81 409 Keyswitch open/close 82 Remote Access - 410 411 Call
CID# Reporting Code Programming Value 525 Reversing relay disabled AE 526 Notification appliance chk. #3 disabled AF 527 Notification appliance chk. #4 disabled B0 Modules - 530 531 Module added B1 532 Module removed B2 Communication Disables - 550 and 560 551 Dialer disabled B3 552 Radio transmitter disabled B4 Bypasses - 570 570 Zone bypass B5 571 Fire bypass B6 572 24Hr.
Index Numerics 001 to 016 .................................................................15–18 021 to 036 ...........................................................19, 21, 34 058 .................................................................................19 059 .................................................................................19 060 .................................................................................15 061 ..................................................................
A C AC failure report code .......................................................33 AC power ..........................................................................7 AC power failure warning ..................................................36 Account number ...............................................................30 Activation event (onboard) .................................................34 Activation event (wireless) .................................................35 Adding ...............
Deleting ............................................................................6 Deleting wireless zones ....................................................19 Dialer & Reporting Settings Alternate Dial Option ..................................................31 Auto-test report .........................................................32 Console account number ............................................30 Console telephone numbers .......................................
Normal state ..............................................................35 Onboard PGM delay ..................................................34 Setting PGM1 & PGM2 Function .................................34 Wireless PGM delay ...................................................35 X10 option ................................................................35 Programming methods Feature select programming .......................................13 Paradox Memory Key .......................................
Timers Alarm Transmission ...................................................18 Auto-arm ..................................................................22 Auto-zone Shutdown ..................................................17 Bell Cut-off ................................................................24 Check-in Supervision .................................................24 Closing Delinquency ..................................................23 Delay between dialing attempts .........................
WARRANTY EQUIPMENT MAINTENANCE FACILITY Paradox Security Systems Ltd. (“Seller”) warrants its products to be free from defects in materials and workmanship under normal use for a period of one year. Except as specifically stated herein, all express or implied warranties whatsoever, statutory or otherwise, including without limitation, any implied warranty of merchantability and fitness for a particular purpose, are expressly excluded.
For technical support in Canada or the U.S., call 1-800-7911919, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST. For technical support outside Canada and the U.S., call 00-1-450491-7444, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST. Please feel free to visit our website at www.paradox.com. paradox.
