MG5000 V4.7 MG5050 V4.7 MG5050 EN V4.
Table of Contents Introduction...................................................................... 1 Features.............................................................................................. System Overview ................................................................................ Modules Current Consumption List .................................................... Specifications......................................................................................
Maximum Dialing Attempts ............................................................... Maximum Dialing Attempts - VDMP3 ............................................... Delay Between Dialing Attempts ...................................................... Switch to Pulse on 5th Attempt......................................................... Alternate Dial Option......................................................................... Force Dial Option........................................................
Part 1: Introduction 1.1 Features • 32 zones (any of which can be wireless or keypad zones). • 32 users and 32 remote controls (one per user). • In-field upgrades: Update the panel’s firmware by connecting it to a PC via a 307USB Interface and then using the Winload software (V2.80 or higher). • Menu-driven programming for the Installer, Master, and Maintenance codes. This enables you to program the panel through a simple and easy to use interface, without the use of section numbers.
1.4 Specifications MG5000 / MG5050 Power rating 16.5 VAC (50 or 60Hz) minimum 20 VA (40 VA recommended) Power consumption MG5000: 1.2A(Max.), 85mA (Idle) MG5050: 1.2A(Max.), 95mA (Idle) Aux. BUS * 600 mA typical, 700 mA maximum, fuseless shutdown at 1.
Part 2: Installation 2.1 Location and Mounting Before mounting the cabinet, push the five white nylon mounting studs into the back of the cabinet. Pull all cables into the cabinet and prepare them for connection before mounting the circuit board into the back of the cabinet. Select a centralized installation site on the main floor that isn't easily accessible to intruders and leave at least 5cm (2in) around the panel box to permit adequate ventilation and heat dissipation.
2.6 MG5050 / MG5050 EN PCB Layout MG5050 EN 50131 Immunity to Attenuation Test Charge LED: Charging and battery test LED Status LED: • Flash once every second = Normal • Flashes ON 1 second and OFF 1 second = Any trouble • Always ON = Panel is using phone line • Fast flash 6 seconds after power up = Installer lock enabled When performing the attenuation test, replace antenna A with the following: • For a 433 MHz panel, use an antenna with a length of 10.2 cm (4 in.
2.7 Metal Box Installation The crosses and dotted line represent the mounting location. If you need specific dimensions, contact Paradox Distributor Support. For UL recommended installation for the MG5000 only, place the PCB one notch lower than the mounting location. MG5050 / MG5050 (11x11”) 2.
2.10 Single Zone Inputs Detection devices such as motion detectors and door contacts are connected to the control panel's zone input terminals. Figure 3 demonstrates single zone input terminal connections recognized by the panel. Once connected, the associated zone's parameters must be defined.
2.11 Advanced Technology Zone (ATZ) Connections The ATZ feature is a software oriented feature that enables two detection devices to be installed per hardwired input terminal. Each detection device has its own zone, displays its zone status on the keypad and sends its own alarm codes. Fire zones cannot be doubled.
Part 3: Programming Methods 3.1 WinLoad Software for Windows Program the control panels remotely or on-site using the WinLoad Software (V2.80 or higher) for Windows®. For more information, contact your local Paradox Distributor or visit our web site at paradox.com. If you are using the WinLoad software, you must program the features (see Settings for WinLoad Software on page 51). Update the panel’s firmware by connecting it to a PC via a 307 Direct Connect Interface and then using the Winload software.
3.2.3 Data Display Mode (except K32LCD and K32LCD+) In the Data Display Mode you can view the programmed contents of each section one digit at a time. Figure 5: Data Display Mode To access the Data Display Mode, press the [ENTER] key after entering a section and before entering any data. The four LEDs as indicated below will begin to flash indicating that you are in the Data Display Mode.
Figure 6: Paradox Memory Key Blue LED flashes only during transfer between the key and the PC. Prevents overwriting content of key. Connection to USB Com Port. Connection to module or panel. Copy and download content of the key. Lock Switch Insert Paradox Memory Key onto the ‘MEMKEY’ connector.
Part 4: LCD Keypad Labels 4.1 Input Keys Key [STAY] [SLEEP] [ARM] [OFF] [BYP] [MEM] 4.
Hebrew Keypad Letter Assignment Hebrew Special Characters Catalogue Greek Keypad Letter Assignment Key [1] [2] [3] [4] [5] [6] [7] [8] Press key once A D H K N P T C Press key twice B E Q L R U Y 032 048 064 080 096 112 160 176 192 208 224 240 033 049 065 081 097 113 161 177 193 209 225 241 034 050 066 082 098 114 162 178 194 210 226 242 035 051 067 083 099 115 163 179 195 211 227 243 036 052 068 084 100 116 164 180 196 212 228 244 037 053 0
Russian Keypad Letter Assignment Russian Special Characters Catalogue Magellan 13
Part 5: Access Codes The control panel supports the following access codes: Installer Code [397]: Used to program all control panel settings except user access codes. Maintenance Code [398]: The Maintenance code is similar to the Installer code. It can be used to enter programming mode, which allows you to program all the features, options and commands except for the panel’s communication settings. The maintenance code is empty by default. System Master Code [399]: Provides full access.
If the system is partitioned (see Partitioning on page 48), user codes with this option enabled can arm and disarm partition 1. If the system is not partitioned, you must assign partition 1 to the user access code. Otherwise, the user access code will be considered disabled. 5.5.
Part 6: StayD Mode 6.1 Overview • NOTE: StayD is automatically enabled when a path is programmed to a keypad. When deleting a wireless keypad (K32RF) from the system, the corresponding path zones will also be deleted. StayD simplifies your life and makes it safer by protecting you 24 hours a day, 7 days a week without ever having to disarm the system - even when entering an armed area.
Part 7: Zone Programming When programming zones, the zone assignments are dependent on the designation of the wireless transmitters, assignment of keypad zones, and the detection devices that are connected to the panel. For wireless assignment, see Wireless Transmitter Programming on page 25 or the Installer Quick Menu of the programming guide. For keypad assignment, see Configuring the Keypad Zone Number on page 9.
7.1.3 Entry Delay 1 (Full Arm) Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 03 Upon regular arming, the zone is Entry Delay 1 (see Entry Delay 1 Zones on page 17). Upon Stay/Sleep arming, the zone is bypassed by the system. See Zone Definition Status on page 21 for any exceptions. 7.1.4 Entry Delay 2 (Full Arm) Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 04 Upon regular arming, the zone is Entry Delay 2 (see Entry Delay 2 Zones on page 17).
7.1.11 Instant Fire Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 11 when a Instant Fire zone opens, whether it is armed or disarmed, the control panel will send the corresponding Alarm Report Code and the alarm is always audible regardless of other settings. Fire alarms generate an intermittent (pulsed) bell/siren output signal as shown in Figure 8 on page 19. Figure 8: Bell/Siren Output during a Fire Alarm 7.1.
7.1.17 24 Hr. Hold-up Zones Sections [001] to [032]: Zones 1 to 32, First Digits = 17 When a 24Hr. Hold-up zone opens, whether it is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 22. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Hold-up alarm. 7.1.18 24 Hr.
7.2 Zone Definition Status There are eight zone definitions that are affected by the Flex-Instant delay (section [720]). The following table shows how the zone definition changes depending on the arm status and if the Flex-Instant delay is enabled. see Zone Definition Status on page 21.
7.4.3 RF Zone Supervision Sections [001] to [032]: Zones 1 to 32 Option [3] OFF = RF Zone Supervision Disabled Option [3] ON = RF Zone Supervision Enabled (default) The panel waits for each of its assigned wireless transmitters to send a status signal within a specified time period (section [706], option [1]) to confirm their presence and functionality.
7.5 EOL Zones Section [706]: Zone Options Option [2] OFF = Zones do not use EOL resistors (default) Option [2] ON = Zones require EOL resistors If all detection devices connected to the control panel have input terminals that require 1K end of line resistors, enable option [2] in section [706]. For details on using EOL resistors, see Single Zone Inputs on page 6. 7.
Part 8: Keyswitch Programming 8.1 Keyswitch Numbering On-board hardwire control panel zones only. Keyswitch Numbering allows you to assign any hardwired input in the system to any of the 32 keyswitch zones in the control panel. UL Note: Do not use keyswitches in UL Listed systems. 8.2 Keyswitch Definitions Keyswitch Definitions determine how a keyswitch is used. 8.2.1 Maintained Keyswitch On-board hardwire control panel zones only.
Part 9: Wireless Features The control panel(s) allows for the addition of up to thirty-two fully supervised wireless transmitters, and up to thirty-two programmable remote controls. 9.1 Wireless Transmitter Programming The programming of the wireless transmitters (detectors and door contacts) is accomplished in two steps: 1. Assign the wireless transmitter to the control panel. 2. Program the zones. Wireless Transmitter Programming can be executed through the Installer Quick Menu in the programming guide.
9.3.2 RF Module Supervision Timer Settings Section [706]: Supervision Options Option [1] OFF = Check-in supervision interval is every 24 hours (default) Option [1] ON = Check-in supervision interval is every 80 minutes Option [1] defines the time period that the control panel will expect a check-in status signal from its assigned wireless transmitters.
Warning: When section [610] is accessed, the panel will copy the saved value of that section to all remotes.
9.10 Option [7] OFF Option [7] ON = Keypad 2 Supervision Disabled = Keypad 2 Supervision Enabled (default) Option [8] OFF Option [8] ON = Keypad 2 Supervision Disabled = Keypad 2 Supervision Enabled (default) Wireless Keypad Live Display Mode Section [587]: Wireless Keypad Options Option [8] OFF Option [8] ON = Live Display Mode Disabled = Live Display Mode Enabled (default) The K32RF has two display modes. By default, the keypad will show all events (e.g. zones in alarm, bypassed zones, etc.
9.14 Wireless Options Section [551] (Repeater 1) and Section [561] (Repeater 2): Wireless Repeater Options Enable or disable the repetition of wireless keypads in this section. Enabling these options for keypads means that the repeater will retransmit any signals relevant to them.
Option [6] OFF Option [6] ON = Repeat Wireless Zone 14 Signals (default) = Repeat Wireless Zone 14 Signals Option [7] OFF Option [7] ON = Repeat Wireless Zone 15 Signals (default) = Repeat Wireless Zone 15 Signals Option [8] OFF Option [8] ON = Repeat Wireless Zone 16 Signals (default) = Repeat Wireless Zone 16 Signals Section [554] (Repeater 1) and Section [564] (Repeater 2): Wireless Repeater Options Enable or disable the repetition of zone signals in these sections.
Section [556] (Repeater 1) and Section [566] (Repeater 2): Wireless Repeater Options Enable or disable the repetition of 2WPGM signals in these sections. Enabling these options for 2WPGMs means that the repeater will retransmit any signals relevant to them.
Part 10: Arming and Disarming Options 10.1 Switch to Stay Arming if no Entry Delay is opened Section [741]: Partition 1, Section [742] = Partition 2 Option [5] OFF = Switch to Stay Arming Disabled (default) Option [5] ON = Switch to Stay Arming Enabled If a user Regular arms a partition, but does not exit through (open and close) an entry delay zone during the exit delay, the control panel can be programmed to switch from Regular arming to Stay arming. 10.
10.8 Restrict Arming on Wireless Supervision Trouble Section [703]: Arming/Disarming Options Option [7] OFF = Permit arming on wireless supervision failure (default) Option [7] ON = Restrict arming on wireless supervision failure If this option is enabled, the control panel will not arm the system if the control panel detects a wireless supervision trouble on one or more zones. The control panel will not arm the system until all wireless supervision trouble conditions are rectified.
10.12 Auto-Arming Options (Not to be used with UL installations) Section [741] = Partition 1, [742] = Partition 2 [3] [4] OFF OFF Regular OFF ON Sleep ON OFF Stay When using Timed Auto-arming or No Movement Auto-arming, the control panel can Regular, Sleep or Stay arm the selected partition. 10.13 One-Touch Arming (Not to be used with UL installations) Section [703]: Options [1] to [3] Option [1] ON = Press & hold the [ARM] key for One-touch Regular Arming.
10.19 No Exit Delay Beeps and No Bell Squawk When Stay/Sleep Arming Section [704]: Arming/Disarming Options Option [7] OFF = No Exit Delay Beeps and No Bell Squawk When Stay/Sleep Arming Disabled Option [7] ON = No Exit Delay Beeps and No Bell Squawk When Stay/Sleep Arming Enabled (default) With this feature enabled, the control panel will prevent the bell or siren from squawking and the keypads from beeping during the exit delay, whenever a partition is Stay/Sleep armed. 10.
Part 11: Alarm Options 11.1 Bell Cut-Off Timer Section [747] = Partition 1, [748] = Partition 2 000 = Disabled, 001 to 255 minutes, Default = 4 minutes, 5 minutes minimum for ULC installations After an audible alarm, the bell or siren will stop upon disarming of the partition or when the Bell Cut-Off Timer has elapsed, whichever comes first. 11.2 Recycle Alarm After the Bell Cut-Off Timer and the Recycle Delay have elapsed, the control panel will re-verify the zone status.
11.5 Tamper Bypass Options Section [705]: Zone Options Option [5] OFF = Tampers on bypassed zones will be ignored Option [5] ON = Will generate a tamper if detected on a bypassed zone (default) With option [5] off, the Tamper Recognition feature follows the zone bypass definition. This means the control panel will ignore any tampers detected on a bypassed zone. With option [5] on, Tamper Recognition ignores the bypass definition.
Part 12: Reporting and Dialer settings The following section explains all the features and options that must be programmed in order for your security system to properly report system events to a monitoring station. When an event (e.g. zone in alarm) occurs in the system, the control panel verifies if a report code was programmed in the section corresponding to the event (except Ademco Contact ID “All Codes”).
12.6 System Trouble Report Codes Section [865] to [869] When the system generates one of the instances listed below, the control panel can send the appropriate report code to the monitoring station identifying the type of system trouble. Section [865] • N/A • AC Failure: The control panel has detected a loss of AC power. Transmission of this report code can be delayed. • Battery Failure: Backup battery is disconnected or battery voltage is low. • Auxiliary Supply: Auxiliary power supply has overloaded.
Option [3] ON = Clear arm/disarm/alarm reporting codes (default) Option [4] OFF = Clear trouble reporting codes Option [4] ON = Clear trouble reporting codes (default) Enable all options you want to clear. The respective sets of reporting codes will be cleared after exiting the section. 12.
Table 6: Reporting Formats Value Entered Reporting Format 0 Ademco Slow (1400Hz, 1900Hz, 10BPS) 1 Silent Knight Fast (1400Hz, 1900Hz, 10BPS) 2 SESCOA (2300Hz, 1800Hz, 20BPS) 3 Ademco Express (DTMF 4+2) 4 Ademco Contact ID 5 SIA If Hexadecimals (0 to FF) are used to program the report codes, verify that the pager also supports Hexadecimals. If the pager does not support Hexadecimals, use only the digits 0 to 9.
When a reportable event occurs in the system, the panel will begin dialing the numbers sequentially starting from MSTN 1 (if enabled), skipping any disabled numbers and stopping once all selected telephone numbers have been called. After a certain amount of failed attempts (section [831]) at trying to call the monitoring station, the control panel will then dial the selected backup telephone number (if enabled; see Programming Guide).
12.21 Force Dial Option Section [800]: Dialer Options Option [5] OFF = Force Dial Disabled Option [5] ON = Force Dial Enabled (default) With option [5] is enabled, the panel will dial a telephone number even if no dial tone is present after 4 seconds. 12.
12.25 Power Failure Report Delay Section [839] 001 to 255 minutes, Default = 15 minutes The control panel will transmit the AC Failure report code programmed in section [865] after the Power Failure Report Delay period has elapsed. 12.
12.31 Personal Reporting Delay Section [836]: Communication Timers 000 to 255 times, Max. 127, Default = 5 When using the Personal Reporting Format, the control panel will wait for the Personal Delay period before transmitting the report codes. This is to allow time for the system to provide a dial tone or to bypass the “welcome” message before sending data. This section applies to the Plug-in Voice Dialer when using a VDMP3. 12.
Part 13: Programmable Outputs A PGM is a programmable output that toggles to its opposite state (i.e. a normally open PGM will close) when a specific event has occurred in the system. For example, a PGM can be used to activate bells or strobe lights, open/close garage doors and much more. When a PGM activates, the control panel triggers any device or relay connected to it. The control panel includes two/four onboard PGMs. It can support up to a total of 16 PGMs.
When armed, the PGM will pulse once every 30 seconds. Option [6] OFF = PGM Pulse on any alarm disabled (default) Option [6] ON = PGM Pulse on any alarm enabled This option sets the PGMs to pulse on any alarm. Option [7] OFF Option [7] ON = PGM Pulse on any alarm Partition 1(default) = PGM Pulse on any alarm Partition 2 Program PGMs to pulse during an alarm for either partition. With this feature enabled, and in combination with the Follow Arm/ Stay Arm/Sleep Arm PGM type, the PGM will mimic the Arm LED.
Part 14: System Settings 14.1 Version Number Display Enter section [980] to view the version number of the panel. The first digit will appear. Press [ENTER] to scroll through each consecutive digit (the keypad will beep twice after every digit in the version number). Once the version number has been fully displayed, an acknowledgment beep (3 beeps) will sound and the first digit will be displayed again. 14.
Timer, all the keypad’s LEDs will be off until either a key is pressed or an access code is entered. When the system exits Confidential Mode, the keypads will display the system’s status. Confidential Mode is activated by enabling option [3]. Option [4] regulates whether the keypads will be activated at the touch of a key or only when an access code is entered. Option [5] determines the amount of time without action before the system enters Confidential Mode (5 seconds or 2 minutes). 14.
14.11 Audible Trouble Warning Except AC Failure Section [700]: General System Options Option [3] OFF = Audible trouble warning except AC failure (default) Option [3] ON = Audible trouble warning except AC failure When this option is enabled the panel will generate an audible trouble warning on all troubles except AC failure. 14.
Part 15: Settings for WinLoad Software WinLoad has not been verified by UL. 15.1 Panel Answer Options The following two options define how the control panel answers an incoming call from a computer using the WinLoad Software for Windows®. 15.1.
15.6 Answer WinLoad Software [ENTER] + [INSTALLER CODE] + [SLEEP] In order to perform on-site upload/download connect your computer directly to the control panel using an ADP-1 line adapter. In the WinLoad software set Dialing Method to Blind Dial. Program the panel telephone number in WinLoad software and follow the instructions on the ADP-1 adapter.
Part 16: User Operation 16.1 Alarm Display If an alarm has occurred on a zone, the respective zone LED will flash, the [MEM] key will light up, and the zones will be stored in memory. These respective LEDs will continue to flash until disarming even if the zones are restored. To exit this mode and switch to live display mode before disarming, press the [CLEAR] key. Once the system is disarmed, the zones’ LEDs will turn off, while the [MEM] key remains lit.
The whole Paradox team wishes you a successful and easy installation. We hope this product performs to your complete satisfaction. Should you have any questions or comments, please contact us. For support, please contact your local distributor or contact Paradox at +1-450-491-7444 Monday to Friday, from 8:00 a.m. to 5:00 p.m. EST. You may also e-mail us at support@paradox.com. Additional information can be found on our website www.paradox.com/support Printed in Canada - 03/2019 PARADOX.
