759MG V2.
Table of Contents Introduction...................................................................... 1 Features.............................................................................................. 1 Specifications...................................................................................... 1 Installation........................................................................ 2 Location and Mounting ....................................................................... Earth Ground ......
Settings for WinLoad Software .................................... 40 Panel Answer Options ...................................................................... Panel Identifier.................................................................................. PC Password .................................................................................... PC Telephone Number ..................................................................... Call WinLoad Software ..........................................
Part 1: Introduction 1.1 Features • Up to 15 fully programmable zones • Two completely independent partitions. Many of the features and options in the Spectra System can be independently set for each partition such as Event Reporting, Entry/Exit Delay, Auto-arming and many more. All zones, the keyswitches and all user codes are assigned to specific partitions, which makes this a true partitioned system.
Part 2: Installation 2.1 Location and Mounting Before mounting the cabinet, push the five white nylon mounting studs into the back of the cabinet. Pull all cables into the cabinet and prepare them for connection before mounting the circuit board into the back of the cabinet. Select a centralized installation site on the main floor that isn't easily accessible to intruders and leave at least 5cm (2in) around the panel box to permit adequate ventilation and heat dissipation.
Figure 2: Spectra 1759MG Control Panel Overview “STATUS” LED: Flash once every second = normal ON 1 second and OFF 1 second = trouble Always ON = panel is using phone line Fast flash 4 seconds after power up = installer lock enabled “RX” LED: Flashes quickly when receiving signals from wireless devices. Antennae Paradox Memory Key (PMC-3) Warning: Do not cut, bend or alter the antennae & ensure that electrical wires do not cross over the antennae as these may affect the signal reception.
2.5 Auxiliary Power Terminals* The auxiliary power supply terminals can be used to power motion detectors, keypads and other modules or accessories in the security system. A fuseless circuit protects the power supply against current overload and automatically shuts down if the current exceeds 1.1A. If this occurs, the Maximum Auxiliary Current failure will appear in the keypad’s trouble display (see page 42).
Figure 3: Relay and PGM Connections Alarm Relay (5A) can be programmed to follow the BELL output or the Global PGM. AUX+ or External Power Supply. See Programmable Output Connections* on page 4. External Power Supply Any device such as a strobe light or siren 2.9 Single Zone Inputs Detection devices such as motion detectors and door contacts are connected to the control panel's zone input terminals. Figure 4 demonstrates single zone input terminal connections recognized by Spectra.
keypad can then communicate the status of the zone to the control panel. A maximum of two keypad zones can be used with each control panel. After connecting the device, the zone's parameters must be defined. For details on zone recognition and Zone Programming on page 12. Also, refer to the feature Reassign Keypad Zone 2 on page 12.
Part 3: Programming Methods 3.1 WinLoad Software for Windows* Program the Spectra Series control panels remotely or on-site using the Winload Software for Windows®. For more information, contact your local Paradox Distributor or visit our web site at www.paradox.ca. If you are using the WinLoad software, you must program the features explained on pages 40 and 41. * Not investigated by UL. 3.
Figure 8: Data Display Mode (LED Keypads Only) To access the Data Display Mode, press the [ENTER] key after entering a section and before entering any data. The three LEDs as indicated below will begin to flash indicating that you are in the Data Display Mode. 1686H 1686V 1689 Each time the [ENTER] key is pressed, the keypad will display the next digit in the current section and will continue through all the following sections one digit at a time without changing the programmed values.
NOTE: The keypad can be ordered with or without an anti-tamper switch. If the keypad has no antitamper switch, key [3] will be OFF by default. If the keypad has an anti-tamper switch, key [3] will be ON by default. 3.4 Programming Using A Paradox Memory Key* Copy the sections of one Spectra control panel into the Paradox Memory Key (PMC-3). Then copy the contents of the Memory Key into as many Spectra control panels as needed. Each panel is programmed in less than 3 seconds.
Part 4: Access Codes The Spectra 1759MG control panel supports the following access codes: 4.1 Installer Code: Used to program all control panel settings except user access codes. System Master Code (001): Provides full access. Arm and disarm using any method described in the User Code Options on page 10 as well as program the user access codes. Master Code 1 (002): Permanently assigned to partition 1.
4.4.2 Partition 2 Assignment Sections [302] to [348]: User Codes 002 to 048 Option [2] OFF = Deny access to partition 2 (default) Option [2] ON = User code has access to partition 2 If the system is partitioned (see Partitioning on page 36), user codes with this option enabled can arm and disarm partition 2. If the system is not partitioned, the control panel ignores this option. 4.4.
Part 5: Zone Programming When programming zones, the zone assignments are dependent on where the detection devices are connected to in the system (see Table 4). In installations that require using mostly the expansion inputs (see section 5.1), refer to Reassign Keypad Zone 2 on page 12 and Reassign Zones to Expansion Inputs on page 13.
5.3 Reassign Zones to Expansion Inputs Section [126]: General Options Option [8] OFF = Reassign Zones to Expansion Inputs Disabled (default) Option [8] ON = Reassign Zones to Expansion Inputs Enabled In installations that require using mostly the expansion inputs, such as using wireless zones, 10-Zone LED keypads may be unable to display some of the zones.
5.5.1 Entry Delay 1 Sections [001] to [015]: Zones 1 to 15, First Digit = 1 When the system is armed and a zone defined with Entry Delay 1 opens, the control panel will generate an alarm after the programmed Entry Delay 1 Timer elapses. This is to provide users with enough time to enter the protected area and disarm the system. To program the Entry Delay 1 Timer, key in the desired 3-digit delay value (000 to 255 seconds, Default = 45 seconds) into section [069].
5.6.2 Standard 24Hr Fire Zone Sections [001] to [005]: Zones 1 to 5, First Digit = 8 Whenever a Standard 24Hr Fire Zone opens, whether it is armed or disarmed, the control panel will generate the following: • The control panel can send the corresponding Alarm report code from sections [187] to [190]. • If a tamper/wiring fault occurs on a fire zone, the control panel can send a Fire Loop Trouble report code programmed in section [206] to the monitoring station.
5.9 Zone Options As demonstrated in Figure 10 on page 13, sections [001] to [015] represent zones 1 through 15 respectively. After entering the first two digits, select one or more of the following Zone Options by using the Multiple Feature Select Programming Method (see page 7): 5.9.
5.9.6 Delay Before Alarm Report Code Transmission Sections [001] to [015]: Zones 1 to 15 Option [7] OFF = Delay Alarm Transmission Disabled (default) Option [7] ON = Delay Alarm Transmission Enabled for Selected Zone When an alarm condition occurs on a zone with this option enabled, the control panel enables the bell/siren output, but does not report the alarm to the monitoring station until the end of the Alarm Before Transmission Delay.
Part 6: Wireless Features The Spectra 1759MG allows for the addition of up to eight fully supervised Magellan wireless transmitters, and up to eight programmable remote controls. To program a wireless fire zone, refer to Programming a Wireless Fire Zone on page 15. 6.1 Wireless Transmitter Programming The programming of the wireless transmitters (detectors and door contacts) is accomplished in two steps: 1. Assign the wireless transmitter to the Spectra 1759MG. 2. Program the zones. 6.1.
6.2 Viewing the Wireless Transmitter Signal Strength Sections [631] to [638] Once wireless transmitters have been installed and assigned to the Spectra 1759MG, the signal strength of each transmitter can be verified in sections [631] to [638]. Each section represents the signal strength viewer for a specific device. For example, section [631] is the viewer for the device in section [601] and section [638] is the viewer for the device in section [608].
Option [1] enables the Check-in Supervision feature. The Spectra 1759MG waits for each of its assigned wireless transmitters to send a status signal within a specified time period (as programmed in Check-in Supervision Timer Settings on page 20) to confirm their presence and functionality.
6.5.3 Assigning Remote Controls to User Access Codes Sections [701] to [708]: Remote Controls 1 to 8 respectively Each remote control must be assigned to a user access code. All user access codes are given a user number from 001 to 048. Enter the desired user number in a section from [701] to [708] that represent the remote control assigned in sections [731] to [738] (refer to Assigning a Remote Control to the Spectra 1759MG on page 20).
Figure 13: Remote Control Button Identification Four button Remote Control Table 7: Button Options [FORCE] = Button Disabled [7] = Regular Arm and Disarm [1] = Regular Arm [8] = Generate a Panic 1† Alarm (Police) [2] = Stay Arm [9] = Generate a Panic 2† Alarm (Medical) [3] = Instant Arm [A] = Generate a Panic 3† Alarm (Fire) [4] = Force Arm [B] = Activates any PGMs that have Event Group #07* as their Activation Event [5] = Disarm [C] = Activates any PGMs that have Event Group #08* as their Acti
7.3 Regular Arming Switches to Force Arming (Not to be used with UL Installations) Section [131]: Arming/Disarming Options Option [2] OFF = Regular Arming Switches to Force Arming Disabled (default) Option [2] ON = Regular Arming Switches to Force Arming Enabled With this feature enabled, the control panel will always Force arm instead of Regular arm when a valid user access code with the Force Arming Option is entered.
7.7.1 No Movement Timer Section [075] = Partition 1, [076] = Partition 2 001 to 255 x15min, Default = Disabled Select the section corresponding to the desired partition and program the interval of time without movement you wish the control panel to wait before arming and/or sending the No Movement report code. If No Movement Auto-arming is disabled, the control panel can still send the No Movement report code when no movement has been detected for the period specified by the No Movement Timer. 7.
7.14 No Exit Delay Beeps and No Bell Squawk When Stay Arming Section [131]: Arming/Disarming Options Option [5] OFF = No Exit Delay Beeps and No Bell Squawk When Stay Arming Disabled (default) Option [5] ON = No Exit Delay Beeps and No Bell Squawk When Stay Arming Enabled With this feature enabled, the control panel will prevent the bell or siren from squawking and the keypads from beeping during the exit delay, whenever a partition is Stay armed. Part 8: Alarm Options 8.
8.3.1 Tamper Bypass Options Section [132]: Zone Options Option [3] OFF = Will generate a tamper if detected on a bypassed zone (default) Option [3] ON = Tampers on bypassed zones will be ignored With option [3] on, the Tamper Recognition feature follows the zone bypass definition. This means the control panel will ignore any tampers detected on a bypassed zone. With option [3] off, Tamper Recognition ignores the bypass definition.
Part 9: Reporting and Dialer settings The following section explains all the features and options that must be programmed in order for your security system to properly report system events to a monitoring station. When an event (e.g. zone in alarm) occurs in the system, the control panel verifies if a report code was programmed in the section corresponding to the event (except Ademco Contact ID “All Codes”).
9.1 Reporting/Dialer (Enable/Disable) Section [135]: Dialer Options Option [3] OFF = Reporting/Dialer Disabled (default) Option [3] ON = Reporting/Dialer Enabled 9.2 Report Codes A report code is a 1- or 2-digit hexadecimal value consisting of digits from 1 to F. Each section from [160] to [213] represents a set of up to four specific events and each of these events can be programmed with a separate 1- or 2-digit report code.
9.2.6 Zone Alarm Restore Report Codes Sections [191] to [194] A report code can be programmed for each of the 15 available zones. The control panel can transmit these report codes to the monitoring station identifying which zone was restored. A zone is restored when it closes after generating an alarm or once the bell has cut-off after alarm generation. Please refer to Zone Restore Report Options on page 34. 9.2.
9.2.11 System Trouble Restore Codes Sections [208] to [210] Whenever the system restores one of the troubles listed in System Trouble Report Codes on page 29, the control panel can send the appropriate report code to the monitoring station identifying the type of system trouble restore. If Telephone Line Monitoring is enabled (see page 34), the control panel can also transmit a TLM Restore report code. 9.2.
Table 9: Reporting Formats Value Entered Reporting Format 1 Ademco Slow (1400Hz, 1900Hz, 10BPS) 2 Silent Knight Fast (1400Hz, 1900Hz, 10BPS) 3 SESCOA (2300Hz, 1800Hz, 20BPS) 4 5 (Default) 6 Ademco Express (DTMF 4+2) Ademco Contact ID Pager Format If Hexadecimals (0 to FF) are used to program the report codes, verify that the pager also supports Hexadecimals. If the pager does not support Hexadecimals, use only the digits 0 to 9.
9.6 Pager Delay Section [083] 001 to 255 seconds, default = 5 seconds When using the Pager Reporting Format (see page 31), the control panel will wait for the Pager Delay period before transmitting the report codes. This is to allow time for the pager system to provide a dial tone or to bypass the “welcome” message before sending data. 9.
9.12 Maximum Dialing Attempts Section [081] 001 to 016 attempts, Default = 8 attempts The value programmed in section [081] determines how many times the control panel will re-dial the same monitoring station telephone number before proceeding to the next number. 9.13 Delay Between Dialing Attempts Section [082] 000 to 255 seconds, Default = 20 seconds This delay determines the amount of time the control panel will wait between each dialing attempt. 9.
With option [1] OFF, the control panel will send the Disarming report codes (see page 28) to the monitoring station every time the system is disarmed. With option [1] ON, the control panel will send the Disarming report codes to the monitoring station when the system is disarmed following an alarm. 9.
1) 2) 3) 4) Enter section that represents the desired PGM. PGM1 = [120], PGM2 = [122], Global PGM = [124] Enter the Event Group #. Enter the Sub-Group #. Enter the Partition # (01 = Partition 1 02 = Partition 2 99 = Both Partitions) The “AC Loss” PGM Event will only occur after the Power Failure Report Delay elapses (see page 33). 10.
Part 11: System Settings 11.1 Hardware Reset Performing a hardware reset will set all control panel settings to factory default except for the Panel ID and PC Password. Also, the event buffer will not be erased. To perform a power down reset: 1) Make sure the Installer Lock is disabled (see below) 2) Remove battery and AC power from the control panel. 3) Set the RESET jumper to on by placing a jumper on the RESET pins of the control panel. 4) Re-connect AC and battery power to the control panel.
If you notice a gain or loss in control panel time, calculate the average gain or loss per day and program the opposite amount in order to automatically correct the time setting every 24 hours. Example: If a control panel loses 4 minutes per month, this represents an average loss of 8 seconds per day. Therefore, programming 008 (plus 8 seconds) into section [088] would compensate for the 8-second loss. 11.
11.11 Installer Quick Functions Keys After entering the Installer Code, you can press a key to perform specific actions as described below. 11.11.1 Installer Test Mode [ENTER] + [INSTALLER CODE] + [TBL] / [TRBL] The Installer Test Mode allows you to perform walk tests where the bell or siren will squawk and the keypad will emit a confirmation beep to indicate opened zones. To enter this mode, simply enter the Installer Code then press the [TBL] or [TRBL] key. The keypad will emit a confirmation beep.
11.
Part 12: Settings for WinLoad Software WinLoad has not been verified by UL 12.1 Panel Answer Options The following two options define how the control panel answers an incoming call from a computer using the WinLoad Software for Windows®. 12.1.
12.6 Answer WinLoad Software [ENTER] + [INSTALLER CODE] + [FORCE] In order to perform on-site upload/download connect your computer directly to the control panel using an ADP-1 line adapter. In the WinLoad software set Dialing Method to Blind Dial. Program the panel telephone number in WinLoad software and follow the instructions on the ADP-1 adapter.
Part 13: User Operation 13.1 Trouble Display The Spectra system continuously monitors fourteen possible trouble conditions. When a trouble condition occurs, the [TBL] key or [TRBL] indicator will illuminate on the LED keypads or “Trouble” will appear on the LCD keypad’s screen. Press the [TBL] or [TRBL] key to switch to the trouble display.
Table 11: Trouble List LED # 13.2 Description Details [FORCE] or [16] Keypad Fault If the keypad is no longer communicating with the control panel, the [TBL] or [TRBL] will flash, the [FORCE] key will illuminate (the LCD keypad displays “Keypad Fault”) and the keypad will emit four consecutive beeps at 5-second intervals. Press any key on the keypad to terminate the “beeping” sequence. When communication has been restored, the system will revert to previous status.
13.4 Regular Arming This method, commonly used for day-to-day arming, will arm all the zones in the selected partition. If you make a mistake, the keypad will emit a rejection beep. When you have correctly armed the system, the appropriate ARM indication will turn on and the exit delay will be initiated. Please note that Regular arming can also be activated through Auto-arming, Keyswitch arming or Onetouch arming. How Do I Regular Arm? 1) Green “READY” indicator must be illuminated.
How do I Program Bypass Entries? 1) Press the [BYP] key. 2) Key in a valid [ACCESS CODE]*. 3) Select one or more [ZONES] you wish to bypass. 4) Once you have entered the desired bypass entries, press the [ENTER] key to accept these entries. *IF YOU HAVE ACCESS TO BOTH PARTITIONS: Press the key corresponding to the desired partition. 13.8.1 Bypass Recall Feature After disarming the system, the control panel will erase the bypass entries.
Code 2. Please note that the control panel will enter a 60-second exit delay period before arming the system. At this point, Autoarming can be cancelled by entering a valid access code. 13.13 Alarm Memory Display A record of all alarm situations that occur will be stored in memory. After disarming the system, pressing the [MEM] key will display which zones were in alarm during the alarm period. To exit the Alarm Memory Display, press the [CLEAR] key.
FCC Warnings IMPORTANT INFORMATION This equipment complies with Part 68 of the FCC rules subpart D and CS03. Inside the cover of this equipment is a label that contains, among other information, the FCC registration number of this equipment. NOTIFICATION TO TELEPHONE COMPANY Upon request, customer shall notify telephone company of particular line to which the connection will be made, and provide the FCC registration number and the ringer equivalence of the protective circuit.
CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority, or electrician, as appropriate. The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading.
INDEX Numerics 24Hr. Buzzer Zone ...........................................................14 24Hr. Delayed Fire Zone .................................................15 24Hr. Standard Fire Zone ................................................15 A AC Failure Report Code ..................................................29 AC Power ...........................................................................2 Access Codes ..................................................................10 Length ...........
E Zone Connection ........................................................... 5 Emergency Panic Report Code ....................................... 29 Entry Delay ...................................................................... 14 EOL Zones ...................................................................... 17 Event Buffer Transmission .............................................. 41 Event Call Direction .........................................................
Partial Arming Report Code .............................................28 Partition Account Numbers ..............................................30 Partition Assignment, Zone ..............................................15 Partitioning .......................................................................36 PC Exit Report Code .......................................................30 PC Password ...................................................................40 PC Telephone Number ...................
Trouble Restore Codes ................................................. 30 T Tamper Bypass Options .................................................. 26 Tamper Recognition ........................................................ 25 Telephone Line Connection ............................................... 4 Telephone Line Monitoring (TLM) ................................... 34 Telephone Number, PC ................................................... 40 Telephone Numbers ......................................
Notes
For technical support in Canada or the U.S., call 1-800-791-1919 for English or 1-866-912-0600 for French, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST. For technical support outside Canada and the U.S. call 00-1-450-491-7444, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST. Please feel free to visit our website at www.paradox.ca. 780 Industriel Blvd., Saint-Eustache (Quebec) J7R 5V3 CANADA Tel.: (450) 491-7444 Fax: (450) 491-2313 www.paradox.
