Network Turret Camera Quick Start Guide 0
Network Turret Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Turret Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Turret Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Network Turret Camera·Quick Start Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Network Turret Camera·Quick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
Network Turret Camera·Quick Start Guide ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket.
Network Turret Camera·Quick Start Guide ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. ● Do not place the camera in extremely hot, cold (the operating temperature shall be -30°C to +60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation.
Network Turret Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 10 1.1 Type I ............................................................................ 10 1.2 Type II ........................................................................... 11 1.3 Type III .......................................................................... 12 1.4 Type IV ..........................................................................
Network Turret Camera·Quick Start Guide 5.2 Hik-Connect Setup ........................................................ 51 5.3 Add Camera to Hik-Connect .......................................... 51 5.4 Initialize the Memory Card ............................................
Network Turret Camera·Quick Start Guide 1 Appearance Description This camera series of turret camera has four appearance types. 1.1 Type I 1 4 6 2 3 5 Figure 1-1 Overview of Type I Turret Camera Table 1-1 Description No. Description No.
Network Turret Camera·Quick Start Guide 1.2 Type II 1 4* 5 2 7 3 6 Figure 1-2 Overview of Type II Turret Camera Table 1-2 Description No. Description No. Description 1 Trim Ring 4* Photosensitive Resistance 2 Enclosure 5 Camera 3 Mounting Base 6 Power Cord 7 10M/100M self-adaptive Ethernet Interface Note: The item marked with the "*" is only supported by certain camera models.
Network Turret Camera·Quick Start Guide 1.3 Type III 1 4 2 5 6 3 10 11 7 8 9 Overview of Type III Turret Camera Table 1-3 Description No. Description No.
Network Turret Camera·Quick Start Guide No. Description No. Description 4 Camera 10 Memory Card Slot 5 Power Cord 11 MIC 6 10M/100M self-adaptive Ethernet Interface Note: Press Reset button about 10s when the camera is power on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 1.
Network Turret Camera·Quick Start Guide Table 1-4 Description No. Description No. Description 1 Trim Ring 5 Power Cord 2 Enclosure 6 10M/100M self-adaptive Ethernet Interface (PoE) 3 Mounting Base 7 RST (Reset) Button 4 Camera 8 Memory Card Slot Notes: ● For this type IV camera, the layout of memory card slot and reset button may be different from model to model.
Network Turret Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC or PoE (802.3af), please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Turret Camera·Quick Start Guide 2). Rotate the trim ring anticlockwise to take it off from the camera. 3). Separate the camera and the enclosure. ③ Trim Ring ② Camera Lock Screw ① Mounting Base Figure 2-1 Disassemble the Camera 2. Drill the screw holes and the cable hole on the ceiling according to the drill template.
Network Turret Camera·Quick Start Guide There are two cable outlet methods. One is to route the cables through the cable hole, and the other is to route the cables through the side outlet shown below. Figure 2-3 Side Outlet Notes: Three side outlets on the enclosure are selectable, which makes routing the cables easier instead of drilling a cable hole on the ceiling. Use a plier to remove the plastic and route the cables through the hole. 3.
Network Turret Camera·Quick Start Guide Ceiling Figure 2-4 Secure the Mounting to the Ceiling 4. Connect the corresponding power/network cable and then install the camera to the mounting base with the supplied screws. Rotate the camera to secure it. 5. Adjust the Lens. Figure 2-5 Secure the Camera to the Mounting Base 1). Loosen the lock screw.
Network Turret Camera·Quick Start Guide Lock Screw Figure 2-6 Loosen Lock Screw 2). Rotate the enclosure to adjust the pan angle; rotate the camera to adjust the tilt angle. P Direction 360o T Direction 0o to 75o R Direction 360o Figure 2-7 Adjust the Lens 3). Tighten the lock screw to fix the optimum surveillance angle. 6. Attach the trim ring to the camera and rotate the trim ring clockwise to get it secured.
Network Turret Camera·Quick Start Guide Trim Ring Figure 2-8 Install the Trim Ring 2.1.2 Type II Steps: 1. Disassemble the camera. 1). Rotate the enclosure anticlockwise to take it off from the camera. 2). Separate the camera, the mounting base, and the trim ring.
Network Turret Camera·Quick Start Guide ② Trim Ring ① Camera Mounting Base Figure 2-9 Disassemble the Camera 2. Drill the screw holes and the cable hole on the ceiling according to the drill template. Figure 2-10 The Drill Template There are two cable outlet methods. One is to route the cables through the cable hole, and the other is to route the cables through the side outlet shown below.
Network Turret Camera·Quick Start Guide Figure 2-11 Side Outlet Notes: Three side outlets on the enclosure are selectable, which makes routing the cables easier instead of drilling a cable hole on the ceiling. Use a plier to remove the plastic and route the cables through the hole. 3. Fix the mounting base to the ceiling with the supplied expansion screws. Ceiling Figure 2-12 Secure the Camera to the Ceiling 4. Connect the corresponding power/network cable.
Network Turret Camera·Quick Start Guide 5. 6. Install the camera along with the enclosure to the mounting base by anticlockwise rotating the camera. Rotate the enclosure to adjust the pan angle; rotate the camera to adjust the tilt angle. P Direction 360o T Direction 0o to 75o R Direction 360o Figure 2-13 Adjust the Lens 7. Attach the trim ring to the camera and rotate the trim ring clockwise to get it secured. Trim Ring Figure 2-14 Install the Trim Ring 2.1.
Network Turret Camera·Quick Start Guide Steps: 1. Disassemble the camera. 1). Rotate the trim ring anticlockwise to take it off from the camera. 2). Rotate the mounting base anticlockwise to take it off from the camera. 3). Separate the camera and the enclosure. Trim Ring ① ③ ② Enclosure Camera Mounting Base Figure 2-15 Disassemble the Camera 2. Install the memory card. 1). Find the Micro SD/RST cover on the side of the camera.
Network Turret Camera·Quick Start Guide 2). Take off the cover and insert the microSD card into the card slot. microSD Card Figure 2-17 Memory Card Slot 3). Place the cover back. 3. Stick the drill template on the installation place and drill the screw holes and the cable hole on the ceiling according to the drill template. Figure 2-18 The Drill Template 4. Fix the mounting base to the ceiling with two supplied expansion screws.
Network Turret Camera·Quick Start Guide Figure 2-19 Install the Mounting Base 5. 6. Connect the corresponding power/network cable. Refer to the section 2.3 for the waterproof accessory installation if the camera is installed in the outdoor. Install the camera along with the enclosure to the mounting base by anticlockwise rotating the camera. Figure 2-20 Install the Camera 7. Rotate the enclosure to adjust the pan angle; rotate the camera to adjust the tilt angle.
Network Turret Camera·Quick Start Guide 360° P Direction 0° to 75° T Direction 360° R Direction Figure 2-21 Adjust the Lens 8. Attach the trim ring to the camera and rotate the trim ring clockwise to get it secured. Trim Ring Figure 2-22 Install the Trim Ring 2.1.4 Type IV Steps: 1. Disassemble the camera. 1). Rotate the trim ring anticlockwise to take it off from the camera.
Network Turret Camera·Quick Start Guide 2). Loosen the fixing screw. Take the mounting base off from the camera and the enclosure. 3). Separate the camera and the enclosure. ① ③ Fixing Screw ② Figure 2-23 Disassemble the Camera 2. Install memory card. 1). Unscrew the memory card slot cover. 2). Insert the memory card. Memory Card Figure 2-24 Install Memory Card 3). (Optional) to unmount the memory card, push to get it ejected.
Network Turret Camera·Quick Start Guide 4). Screw the memory card slot cover back. 3. Paste the drill template to desired mounting place. 4. Drill the screw holes (for expansion screws) and the cable hole on the ceiling according to the drill template. Note: If the camera is installed to a wooden wall, use self-tapping screws instead of expansion screws. Figure 2-25 Drill Template 5. Fix the mounting base to the ceiling with two supplied screws.
Network Turret Camera·Quick Start Guide Drill Template Mounting Base Figure 2-26 Fix Mounting Base 6. 7. Connect the corresponding power/network cable. Refer to the section 2.3 for the waterproof accessory installation if the camera is installed in the outdoor. Install the camera along with the enclosure to the mounting base. Figure 2-27 Install the Camera 8. Adjust the surveillance angle of the camera. Secure the fixing screw after adjustment.
Network Turret Camera·Quick Start Guide Pan: 0° to 360° Rotate: 0° to 360° Tilt: 0° to 75° Figure 2-28 Adjust Surveillance Angle 9. Attach the trim ring to the camera and rotate the trim ring clockwise to get it secured. Figure 2-29 Install Trim Ring 2.2 Mounting with Brackets This camera series supports mounting with wall mounting bracket and pendant mounting bracket. We take Type IV camera as the demonstration example. 2.2.1 Wall Mounting The wall mount is not included in the package.
Network Turret Camera·Quick Start Guide Steps: 1. Mark the screw holes on desired mounting place. Figure 2-30 Dimension of Demonstrated Wall Mounting Bracket 2. Drill four screw holes with a Φ10 mm drill. 3. Route the cables and fix the bracket with four M6 expansion bolts. 4. Disassemble the camera. Refer to step 1 in ceiling mounting of each camera type. 5. Fix the mounting base to the cap of wall mount with 3 supplied self-tapping screws.
Network Turret Camera·Quick Start Guide Cap Mounting Base Figure 2-31 Fix Mounting Base 6. 7. Connect the corresponding power/network cable. Refer to the section 2.3 for the waterproof accessory installation if the camera is installed in the outdoor. Install the camera and the enclosure to the mounting base, adjust the surveillance angle, and fix the trim ring. Refer to corresponding steps in ceiling mounting of each camera type.
Network Turret Camera·Quick Start Guide 2.2.2 Pendant Mounting The pendant mounting bracket is not included in the package. You need to prepare one in advance, if you adopt this mounting type. Steps: 1. Mark the screw holes on desired mounting place. 2. Drill three screw holes for expansion bolts. 3. Route the cables and fix the pendant mounting bracket to ceiling. Cables Figure 2-33 Fix Pendant Mount 4. Disassemble the camera. Refer to step 1 in ceiling mounting of each camera type. 5.
Network Turret Camera·Quick Start Guide Mounting Base Cap Figure 2-34 Fix Mounting Base 6. Screw the cap to the pendant mount. Pendant Mount Cap Figure 2-35 Install the Cap 7. Connect the corresponding power/network cable. Refer to the section 2.3 for the waterproof accessory installation if the camera is installed in the outdoor.
Network Turret Camera·Quick Start Guide 8. Install the camera and the enclosure to the mounting base, adjust the surveillance angle, and fix the trim ring. Refer to corresponding steps in ceiling mounting of each camera type. Figure 2-36 Pendant Mounting 2.3 Network Cable Waterproof Accessory Installation Purpose: If the camera is installed outdoor, you can adapt the waterproof accessory for the network cable after the camera is secured on the installation surface.
Network Turret Camera·Quick Start Guide ① ② ③ ④ ⑤ ⑥ ⑦ Figure 2-37 Waterproof Accessory Components Table 2-1 Components No. Components 1 Camera’s Network Interface Socket 2 O-Type Gasket 3 Network Plug 4 Waterproof Endcap 5 Waterproof Rubber Gasket 6 Lock Nut 7 Network Cable from Router/Switch Steps: 1. Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof rubber gasket ⑤ (rubber gasket inset ridge must face waterproof endcap), and the waterproof endcap ④ in order. 2.
Network Turret Camera·Quick Start Guide 3. Place the O-type gasket ② onto the end of the camera’s network interface socket ①. 4. Insert the network plug ③ into the camera’s network interface socket ①. 5. Insert the waterproof rubber gasket ⑤ into the waterproof endcap ④, and secure lock nut ⑥ with the waterproof endcap ④. 6.
Network Turret Camera·Quick Start Guide 3 Set the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. 3.1 Wiring Connect the camera to network according to the following figures.
Network Turret Camera·Quick Start Guide 3.2 Activate the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Network Turret Camera·Quick Start Guide Figure 3-3 Activation Interface (Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Turret Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password. Figure 3-4 SADP Interface Note: The SADP software supports activating the camera in batch.
Network Turret Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
Network Turret Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking Enable DHCP.
Network Turret Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Network Turret Camera·Quick Start Guide 4 Access via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Turret Camera·Quick Start Guide Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Network Turret Camera·Quick Start Guide 5 Operate via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.
Network Turret Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
Network Turret Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access. Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera.
Network Turret Camera·Quick Start Guide 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Add Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1.
Network Turret Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Notes: ● The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Network Turret Camera·Quick Start Guide 5.4 Initialize the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
UD07707B 0
